Having problems with your Vacuums ?

My bissell worked well cleaning my carpets it's only 1 year old when i stop'd it to refill water it would turn on put not spray what can ido to fix this problem


Answers :

TAKE OFF THE CLEAN WATER TUB IF IT COMES OFF TO FILL AND LOOK FOR SCREENS OR FILTERS THAT COULD BE PLUGGED OR AT LEAST LOOK FOR THE LINE THAT CARRYS THE WATER TO THE PUMP AND AGAIN CHECK FOR LIKE HARD SOAP AND STICK LIKE A NEEDLE IN IT BUT CARFUL NOT PUNCTURE ANY TUBES THE WORST CASE IS THAT THE PUMP THAT MAKES THE WATER SQUIRT OUT IS BAD SAME AS IT BE IF YOURE CAR STOPPED HAVING WINDOW WASHER FLUID SQUIRT OUT
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My bissell worked well cleaning my carpets it's only 1 year old when i stop'd it to refill water it would turn on put not spray what can ido to fix this problem


TAKE OFF THE CLEAN WATER TUB IF IT COMES OFF TO FILL AND LOOK FOR SCREENS OR FILTERS THAT COULD BE PLUGGED OR AT LEAST LOOK FOR THE LINE THAT CARRYS THE WATER TO THE PUMP AND AGAIN CHECK FOR LIKE HARD SOAP AND STICK LIKE A NEEDLE IN IT BUT CARFUL NOT ... Vacuums

I have a proheat 2x, and the pump will only spray water for a few seconds when unit is turned on, then nothing. The attachment is the same way. I think this is the pump failing, and the unit is only over a year old. How much would a pump cost? If this is the problem.


I just had my pump replaced for $66 and the repairman said this unit is notorious for this problem. He had 6 other units in his shop when we came in. Make sure you keep your clean water tank FULL, as he said the pump fails as soon as it runs dry. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell ProHeat 2x is pouring water out of the bottom anytime it's turned on. I had it in the shop for no water, took it back again for the same problem, took it back again because it had no suction, finally took it apart and found the problem with the suction and fixed it myself. Worked fine for a day and now it is constantly leaking water, if it's turned on, and is useless for anything except for making a mess.


Took the unit apart and discovered my heater had small pinholes in the metal and they had put in silicone, instead of a gasket, which didn't seal. So much for the place I took it to "saving" my heater for me. I repaired it myself by getting a few o ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hoover upright 2000w, HL2005 001 problems:the hoover made a pop sound & turned off. Tried leaving it for 30 mins as suggested in the manual but it still won turn on. Really cannot afford to buy a new 1 & would like to fix it. partner is an electrician so if we have some guidance as to what the problem may be i am confident we can fix it. the hoover is only 18 months old so not very old at all.


... Vacuums

Bissell will spray water when set to water rinse, but as soon as it is set to light, normal, or heavy cleaning, there is no spray. I have tried priming but to no avail. I put plain water in the solution tank to test without ay success. It is like it loses it's prime whenever you try to use a solution mix. Once you set it back to water rinse only and go through the priming steps, it is OK. Any help would be appreciated. Thanks.


Please check the following with liquid in both tanks.\012 \012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\012- Check for ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.


When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Shark s3325 stopped working while steaming; thinking the unit had ran out of water I allowed unit to cool before refilling, however unit over flowed with only 700ml water added. When I plugged unit back into outlet it would not turn on (red light was not on) but I hear a click upon plugging in unit, when turning unit power button on and when turning on the handle switch. Please advise how to resolve this problem.


... Euro-Pro S3325 Handheld Steam Vacuum

Bissell 7700 series, pro heat all rounder. Won't spray water. Have checked the line from the unit to the spray nozzel and all seems clear. Water doesn't seem to be flowing from the tank to the end of the unit where the hose connects into. What could be the problem? Any assistance would be greatly appreciated. Thank You. Steve


HelloGrasp the cleaning solution tank, and remove it from the machine. Reinsert the tank into the machine, making sure it fits snugly in the machine. If the tank is even slightly dislodged, water cannot get into the machine. Visually insp ... Vacuums

My Bissell carpet cleaner will not spray water out the bottom but will spray water out of the hand held thing. What could be the problem and how do I fix it


Hey here is a guide on how to fix your problem.\015\012http://newzealand.bissell.com/images/In ... Vacuums

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate


Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like i ... Vacuums

I posted my problem earlier today that I was having with my Bissell Little Green Machine not dispensing solution, but sucked up no problem. Someone said that the most common problem was a blockage. We put hot water in the reservoir for 15 minutes as advised and it still will not dispense. The fluid is now ''dribbling''so it is better. It is just not spraying. We are able to blow from the end and make bubbles in the reservoir which shows us it is not blocked. Any other suggestions?


Okay. I fixed this on mine. Undo the screws on the handle, right by the trigger. You pull the tubes off the little valve. Push on the button and see if you can blow through the valve. If not, push a pin around in the valve (with it pushed into the ... Bissell 1720-1 Little Green Wet/Dry Vacuum

I have a Hoover SteamVac Carpet Cleaner with Clean Surge. I lent it to my mother who used it without the brush attached underneath. Now it doesn?t **** up water and the brushes don?t turn. Any idea what would?ve broken? Is there a belt that would have burned out? The motor? Anthing I could fix myself, or would I need service for this?


If you go to this URL:\015\012\015\012http://www.vacpartswarehouse.com/Hoover-F7452-s/811.htm\015\012\015\012you will an exploded view of your Hoover. By going down the pictures you will be able to see the internal parts of the unit and ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.


You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums

Again, I have a Bissel Model 3760-4. The same problem as everyone else. The beater bar will not turn. Took apart, nothing. Took to vacuum repair shop and they said it is not getting power to the motor to the beater bar. Seems like a fair number of folks are having this same issue. You would think Bissell would come up with a fix, if nothing else to save their reputation. Thanks Diane


... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Hello good afternoon, i have a Royal Sovereign water dispenser with a little fridge on the bottom part and the problem i am having is that the dispenser wont release cold water and the fridge wont cool either. i would like to know is there any thing i can buy to fix it or do i have to buy a brand new dispenser! Thank you for your time!!


... Vacuums

Suction Problem I just borrowed the Hoover Steam Vac Deluxe w/ 5 brush agitator from my neighbor and it worked ok for the first few minutes, although the suction would stop and go. When I had enough water to dump I did it and when I put it back on it no longer sucked the water up from the carpet. She admits to having it for 15 years, but why did it have to break on me. Makes me look as though I did it!


Check and make sure the dirt water tank is properly on if it it is chech inside the lide to make sure the red stopper is not stuck to the top this will cut off the suction ... Hoover F7431-900 SteamVac Vacuum

BISSELL HELP Have bissell pro heater it would put out water but it will put out soap. How CAN I FIX IT ?


Usually when you can't put out soap, there is a problem with the vale at the bottom of the dispenser, or the seal is not on it and gone or sitting in the hole, needs to be on the dispenser. Same is true for the wter tank valve and seal. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

After two years, my Euro-Pro Shark Steam Mop, Model S3101, no longer ejects steam. I have used tap water. I think the line is clogged with mineral deposits. The light is on when plugged in, and the unit heats up. I even put in vinegar for about an hour to break up the calcium deposits, but it did not correct the problem. How do I fix it, or, where can I take it locally to be fixed (Orange County, CA)?


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have Bex Bissell Proheat. It is one problem requiring fixing each time I use it. Just had a new pump fitted as water not spraying out. Now the water is not being sucked up. For the money this has not been a good product. When it works it is good. But the constant issues each time it is used is frustrating.


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

After fixing rollers not turning the water will not dispense out


Ensure you have water in tank and solution (or water in solution tank). When you start the vacuum up, the pump starts to prime itself. If you have air in the system, it takes a little longer to prime. Allow the vacuum to run for 1 minute before attem ... Bissell 9200 Upright Vacuum

My vacuum makes a wierd sucking and blocking sound when turned on and when you put the extension tube on the suction decreases...but when just the wand handloe is on the suction is excellent...we replaced the barrel thinking it was broken but that hasnt fixed the problem


You did not list the make and model of your unit, so it is difficult to hunt for problems.\015\012\015\012Check to see if any of the tube vents might be open. They should be closed when in use.\015\012Also check to see there are no holes in th ... Vacuums

I have a bissell proheat carpet cleaner that is not spraying water or chemical. Can this be fixed? What is the problem? Thanks for the time and help.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

My Hoover steam vac is not spraying the water. Instead it is ejecting 5 streams. This is a new probolem and in the several years I have used it I haven't had this problem before. I can find nothing in the manual that explains it or "fixes" it;


There is a filter screen under the plastic cover below the brush indicator. If it is dirty clean it. The solution pump works off of vacuum. If this screen is dirty then the pump does not work correctly. Funny, the manual says nothing about this, only ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0853 seconds