Having problems with your Vacuums ?

Eureka the Boss Power Plus belt problem

\015 I have a Eureka the Boss Power Plus and I'm having belt trouble with it. I have replaced belts on it before with no problem, but for some reason now it immediately burns through the new belts I am placing on it. Is this because the roller is broken possibly?\015

Answers :

It could be the beater bar (brush) has bad bearings at the ends or burs on the beater bar section the belt rides on,my money is on the bearings.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka the Boss Power Plus belt problem


It could be the beater bar (brush) has bad bearings at the ends or burs on the beater bar section the belt rides on,my money is on the bearings. ... Vacuums

How do you change the belt in a Eureka Bagless The Boss Power Plus vacuum cleaner


... Eureka 4700A Maxima Bagless Upright Vacuum

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being


Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

Roller brush will not turn on Eureka "The Boss Power Plus" 12 amp


Depending on the model there will be a couple of screws on the top plastic cover. The cover lifts off and the belt is then serviceable. On some models you will need to remove some parts on the bottom too to get the roller out.In any case just l ... Eureka Boss SuperLite Bagless Upright Vacuum, 405AVacuum

Eureka the boss power plus manual - Eureka Power Plus 4703D Bagless Upright Vacuum


... Eureka Power Plus 4703D Bagless Upright Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?


First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.


The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile


... Eureka Smartvac 4870 Bagged Upright Vacuum

How to change a belt on eureka vacuum 4903 f - Eureka Power Plus 4703D Bagless Upright Vacuum


... Eureka Power Plus 4703D Bagless Upright Vacuum

INSTRUCTION MANUAL FOR EUREKA LIGHTSPEED 100 - Eureka 2 Type Dcf4-Dcf18 Upright Vacuum Cleaner Hepa Pleated Washable Filter W/activated Charcoal Whirlwind Mighty Mite Maxima Boss Power Plus Pet Pal Lightforce 300 Lightspeed 100 General Electric Ge 63073 4700 5500


... Eureka 2 Type Dcf4-Dcf18 Upright Vacuum Cleaner Hepa Pleated Washable Filter W/activated Charcoal Whirlwind Mighty Mite Maxima Boss Power Plus Pet Pal Lightforce 300 Lightspeed 100 General Electric Ge 63073 4700 5500

Eureka Boss Model 4703 Type Belt Problem


Belt can be purchased from amazon, click here and take a look: Amazon com eureka boss vacuum belt. I hope this was helpful. Cheers ... Vacuums

Problem getting belt around motor shaft... Eureka The BOSS


Make sure the vacuum is in the upright (locked position) - when you lower the handle, this puts tention on the belt. If it is in the upright and locked position, there is plenty of clearance (unless you have the wrong belt. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have an eureka power plus vacuum floor cleaner and i have no way of opening the botton to the brush to change my belt for the brush since the brush will not turn.


Look for two screws at the edge of the brush housing. You may see these ones on top. They will be black and recessed ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I need to know how to change the belt on my Eureka The Boss Power Light (green and white). Not the mini bagless


... Eureka Vacuums

Vac motor runs but belt wont turn - Eureka Power Plus 4703D Bagless Upright Vacuum


Its time to check and/or change your belt. to do this you want to remove the two screws on the top casing and remove the cover. There are detailed belt change instructions on a sticker under the top casing on how to remove the brush and b ... Eureka Power Plus 4703D Bagless Upright Vacuum

I have the Eureka The Boss Power PLus Model # 4703 Type A. When using the detached hose and wand it works OK; however, when using the Vacuum with the hose attached it doesn't work well at all.


... Vacuums

My eureka boss power plus upright vacuum is making a terribly loud and has a burning odor. This vacuum has only been used a handful of times. Anything I can do?


The belt is slipping because something is binding up the brushes. ... Eureka 402A Bagless Upright Vacuum

I have the eureka boss smart vac upright and was cleaning a very dirty room and the power went off...the bag was full ...is this common or a big problem


Could be a automatic shut off to avoid damage..\015\012\015\012Change the bag and be sure there is no clogs..\015\012\015\012Have a great day ! ... Eureka Vacuums

Smell/suction I have a Eureka Altima Model 2991 Type AVZ. I have suction when I use the power paw and attachments. I have all hoses clear. My brush is spinning and belt is not broken (I opened it up and checked), but I have no suction when I turn it on to vacuum my living room carpet. I also have a burning smell to go with it after about 30 seconds. I've never had a problem with this vacuum cleaner before.


Ours started smelling too, and it seems that the plastic end on the roller brush was melting. In process of finding rollerbrush for it now ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

I have a Eureka The Boss Mini (Model # 442) vacuum cleaner. It is not working properly sometimes Today I did a cleaned the roller brush thoroughly and powered it on to see if it spins at all. It spins only in Carpet model, but stops sometimes. Please can you tell me what could be the problem?


... Electrolux Vacuums

Changing belt for a eureka power plus 4703D - Vacuums


I have listed below a link to the owners manual which has instructions on how to change the belt and a link to the belts you need. Hope it helps! ... Vacuums

Eureka boss power plus


I had this same problem. The brush roll wouldn't spin, smoke came out, and it smelled like burning rubber. I changed the belt thinking that would fix the problem but it didn't, so I took the belt back off and checked the motor shaft in the back and ... Eureka Boss SuperLite Bagless Upright Vacuum, 405AVacuum

Eureka The Boss Power PLus Model # 4703 Type A Ser #: 0728007324 Adapter that goes between the hose and the vacuum body is held on two tabs (screws). The screw tabs have broken off. Where can one obtain a replacement adapter?


... Eureka Power Plus 4703D Bagless Upright Vacuum

How to clean filter on eureka the boss power plus


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0830 seconds