Having problems with your Vacuums ?

I have an older craftsman garage door opener and replacing the keypad. do i have to do anything special


Answers :

No they all work the same once the password is entered it allows the voltage to pass.just install it and program the password that's it.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an older craftsman garage door opener and replacing the keypad. do i have to do anything special


No they all work the same once the password is entered it allows the voltage to pass.just install it and program the password that's it. ... Vacuums

I have a craftsman garage door opener remote control model TX2028 139.18191. The remote stopped opening or closing the garage door. I replaced the battery and tried to re-program it through the LEARN button as per the manual of the Garage 1/2 HP opener. The process has failed after several trials and the remote is still not working. Is there anything else that I can try or should I get a new remote. Thank you


... Vacuums

My craftsman 1/2 hp garage door opener opened but wont close and clinks and lights flash


... Craftsman Vacuums

Have a Genie 2020L garage door opener. Door start to go down then stop and return. Tried cleaner old sensors. Same. Noticed red light on sensor 3blinks then off....repeat constantly. Replaced sensors - same issue. Reset unit...checked all wiring...no jams anywhere.... HELP PLEASE L:-)


... Vacuums

I have a Liftmaster garage door opener and the garage door faces south. Normally the opener works great except at certain times on a sunny day.The sunlight is not directly hitting one of the sensors but the door will comedown as far as half way and then it will go back up and the lights will flash. If I go inside and use the button I can hold it down until the door is fully closed. However, sure is a pain to have to take the car out, go back into the garage, shut the door and then leave the h


Sounds like a problem with a limit switch or something getting in the way of the electric eye that interrupts for safety reasons. \015\012Clean the electric eye transmitter and sensor of debris and cobwebs and make sure the wires are attached properl ... Vacuums

I have an older Blue Max screwdrive. No safety beam on this model. The door will not close with the remote or wired switch. Press = door opens. press = nothing. press = door opens. press = nothing. With latch lever pulled door will open and close easily.


... Genie Company Vacuums

I have a Chamberlain Liftmaster Professional 1/3 hp garage door opener. I'm unable to find the model number, but it was made in April 2004 and has an orange learn button. It has been working fine since it was new, but now will not open or close when the code is entered on the touch pad. When the problem first started the door would close, but not open. I have tried to reprogram a new digital code, but it does not work at all. There are no problems when opening or closing the door with the re


... Vacuums

Matching or changing codes for a stanley garage door opener. I have a mod. 3100.14 opener and am trying to get it to work with a remote that works on my other stanley door. I changed the codes on the remote to match the opener but nothing happens.


... Stanley Vacuums

My garage door opener will start to close then stop and go back to the open position. If I put pressure on the door as it is closing sometimes it will close all the way and sometimes it will return to the open position. Can you help me. Thanks


Sounds like the pressure sensor is being tripped - this is a safety feature on most makes in the last 10 years.Find the make/model of your device and it probably has some knobs on the main unit to adjust. For example, on the ... Vacuums

I have a genie screw type garage-door opener. the fuse blew on the moter drive board , now the door only opens when you push the light button on the wall console ,will not go closed.green light blinks continually. when I power it up it jumps closed then nothing. It seems like the motor is not reversing.


... Genie Company Vacuums

I own a stanley model 7100 garage door and the light does not come on or off when the garage door is open or closing


Hello. Begin by changing the bulb. Get a new bulb which is vibration proof. J. ... Vacuums

I hit the button and just the light comes on,then i hit the button again and the door closes almost all the way but opens and light keeps flashing . the sensors are on and clear of obstructions . it is a wayne dalton quantum 3212 garage door opener.


Hello ccap..... It sounds like one of those sensors has gotten out of alignment with the other. check to see if there is a steady green light on each sensor. If not, adjust until the light is a steady green. Joe\015\012\015\012Thanks ... Vacuums

T.he light on the garage door opener does not come on when the garage door goes up or down. Why?


Either the bulb blown or not wired right when installed. should have one red wire, one black wire and a ground wire, green or copper. ... Craftsman Vacuums

As a new owner to a previously owned home there is a craftsman keypad on the outside of the garage of which we do not know the access code. the home has been through several owners and the folks we purchased the house from did not know the password in order to pass it on to us. we would like to use the keypad but don't know how to change it. can you help? the mode # is 139.53684, thanks for any assistance you may be able to give. PS: there was also another model # on the keypad it is 139.1


... Vacuums

After a brief power outage my Marantec 4700 garage door opener has problems opening/closing. When opening it stops at the fully open position and the lights blink, when closing it automatically reverses just as it fully closes and then the lights start to blink again. I checked for obstructions and tried to reset the limits of travel per the manual, it still does the same thing. Any ideas on what to try next?


This is not a sensor issue, I have a similar problem, sensors work fine, garage door is still fully functional, all operations, including safety sensors work properly, just the overhead lights flash. I suspect there was damage to the power board due ... Vacuums

Dust....dust....dust Hello, I recently bought a house with an older Electrolux Central Vac system. I'm unfamiliar with them, so I'm not sure how to deal with this: I cleaned up some mortar dust with it, and noticed not too long after that when I went into the garage, there was a fog of dust. The hose from the unit is venting into the garage. Is this normal? I have since used it for everyday household cleaning and each time I go back to the garage to a cloud of dust. Is there anything I can


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=113662&thid=662824\015\012Dust....dust....dust\015\012Posted by Kitkatman on Jun 11, 2008\015\012Hello,I re ... Electrolux Central Vacuum

Have 556 Overhead Door Garage door opener with a 109130-390 2 button remote. Lost programming instructions. How do I program??


... Vacuums

I shorted out the light socket on my Chamberlain Professional Garage Door opener. Now it wont open, I am looking for a fuse or reset button, but cant find one. Is there a way to reset it or did I fry the solinoid


First check your house fuse. ... Vacuums

I have a 41a5021-18 chamberlain security+ 1/2 hp garage opener that requires constant pressure on the down position of the wall switch in order to close. If I release the switch the door reverses direction and completely opens.


... Vacuums

I have a genie garage door opener. The unit is 2 weks old. The light comes on but the openere does not open and makes no sound. Help!!


Did it ever work the way it's supposed? ... Vacuums

All lights work opener operates from head, but will not operate from wall control or remote the wall control does turn on the lights like it is suppose to on genie garage door opener model 2022


... Genie Company Vacuums

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

Guardian 2211-L Garage Door opener. Hand Unit worls but unit in garage is clicking and seems not to respond to RF signal but lights up and can manually close


... Vacuums

Looking for a repair manual/parts list/schematic for a Moore-O-Matic Garage Door Opener Model No.XX133.


... Vacuums

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current


I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0756 seconds