Having problems with your Vacuums ?

How do I replace or repair my tristar power nozzle cordI don't know how to get to or how difficult it will be. there is a short in wire because it is separating from the power nozzle.

Answers :

Dear kerri_clark,

Can't you take a picture of tristar power nozzle cord that you mean.
I need to take a look at this to assist you further more.

Hi, Can you provide me with the model number or type of vacuum? Is it a canister,Prostar, Mini or Pure Vacuum? How old is the vacuum?
\015\012Thanks in advance. No need to rate the solution until I have tried to resolve. Thanks in advance.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I replace or repair my tristar power nozzle cordI don't know how to get to or how difficult it will be. there is a short in wire because it is separating from the power nozzle.

Dear kerri_clark,Can't you take a picture of tristar power nozzle cord that you mean.I need to take a look at this to assist you further more.regards,dm ... Vacuums

My electrolux Epic 6500 power nozzle Model N109J will not work. It had an intermittent short which I thought I fixed (some of the insulation on the wires were pinched). I fixed the wires and it worked intermittently for an hour then shut down completely. Could the reset switch have a short? When I press the switch nothing happens.

The switch is definitely a possibility, but other problems can also cause this.\015\012Bad switch, needs replaced.\015\012Broken wiring in power nozzle, wands, hose, or canister.\015\012Bad PN motor.\015\012\015\012I str ... Electrolux Epic 6500 Vacuum

Power Nozzle Model No. N137A (for Electrolux Epic Serial 6500 SR) has a broken wire. Can I get a replacement power nozzle or find a repair place in the Everett, Washington vicinity?

... Electrolux Epic 6500 Vacuum

Power Nozzle reset

If you mean the reset breaker that just has two wires on it, then you can place them back in any order, there is no polarity ... Electrolux Epic 6500 Vacuum

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.

... Kenmore Vacuums

We have a Kenmore canister vacuum cleaner 25614504. It has in intermittant light and power flicker in the power mate unit as it is moving over the floor. This behavior can be simulated by jiggling the power cord where it eners the power mate. I do not know how to enter the power mate to see if there is a loose wire.

... Kenmore 28614 Canister Vacuum

Power nozzle of my S3670 does not work (vacuum itself does work), the headlight bulb in the nozzle is broken. This happened in the past several times - we would bring the vacuum to service center - I don't know what they did other than replacing the bulb. I decided to go to ACE and buy replacement bulb myself, replaced the one in the nozzle - this did not fix the problem. I don't see any fuzes or anything in the nozzle. However, the manuals says to "Use only HOOVER part no. 27317307, which is a

... Hoover S3670 Bagged Canister Vacuum

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks

... Kenmore 23313 Whispertone Bagged Canister Vacuum

Wiring diagram for a rainbow vacumn cleaner power nozzle

... Vacuums

Electrolux 2100 power nozzle motor doesn't run

... Vacuums

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!

... Kenmore Vacuums

I have been trying to register on line and can't get in. I am having problems with my WindTunnel powered nozzle it doesn't want to run and I just got this as a gift May 1st. The power hand tool works but not the other one and I know all the connectins are good

It will have a years warranty on it. Take it in to a warranty repair shop and tell them that yo got it as a gift and when. ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

I have a Husqvarna Embroidery Card reader/writer for a Viking Rose sewing machine, and I want to know if I can plug a 8-volt power supply into it. During our move the power attachment go separated and I don't want to risk the wrong voltage. The unit is for an older machine, not the USB version that is now in use, Thank you in advance.

The Reader/Writer's power cord is a transformer, with input 120VAC 60Hz, 9 Watt. Output is 12VAC 500mA. The connector is a standard small round plug-in. The one we have appeard to be generic and is labeled only " ... Vacuums

The battery will not charge in the sweeper. I can remove the battery and wire it to the power supply for charging and it will charge up and run the sweeper. So the power supply and the battery are both good. Obviously there is a circuit failure in the on board charging control. Anyone know a fix or a likely faulty component? I had a shark handheld about 8 years ago and it developed the same problem. I examined the little circuit board inside but saw no visible indications that would isolate t

... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

Seems to be a short in the power nozzle (light and beater bar sporadically work) while suction is just fine. How to fix the short?

I am having the same problem...great suction but unit on the floor won't vaccuum. I hit the reset button and the rollar still won't work! ... Electrolux Central Vacuum

I only know this model as the Classic, but the colour of the canister in the photo is the same. The machine will not turn on, but when I retract and pull on the cord, the power light comes on briefly. Is there a short? I lent the vacuum to my daughter and perhaps she was rough with the cord.

... Miele S758 Bagged Canister Vacuum

I have an Electrolux Epic 6500 SR vacuum and the hose end with the handle is separating. Power nozzle losing contact intermittently. Is this piece replaceable or repairable?

It is replaceable. Just take it to the nearest Aerus Electrolux store and the service tech will take care of it for you.\015\012Go to the following site and follow instructions to find the stores nearest you. ... Electrolux Epic 6500 Vacuum

Lux 7000 power nozzle

... Electrolux Vacuums

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.

Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

The power nozzle on my c141b model aerus electrolux canister vaccum no longer turns on. It was working when a large stringy object was sucked in. When hitting the red reset button, nothing happens. Is it likely that it is the fuse that needs to be replaced? All wires appear intact (I replaced the elbow assembly a few months ago.), and the sweeper moves freely.

It's not a fuse.\015\012Turn the power nozzle on it's top. Try to rotate the brush. If it won't spin, there's till something holding it. Remove all strings, threads, and whatnot from the roller. Try to rotate it again. If it still won't sp ... Vacuums

When turned on caused, caused a pop at the outlet and don't know if the if the power cord went bad or short somewhere else in the sustem. what do i do and how

Hi, that pop sound you heard at the outlet simply implies that the fuse blew off. What you just need to do is too replace the fuse and if the power cord is having a burn smell, then i will also advise you to change the power cord..Take ca ... Kenmore 23313 Whispertone Bagged Canister Vacuum

The belt in our power nozzle is snapped in half. And were going to buy a replacement, but we don't know how to install it. How do you?

The best thing to do is take the machine to an authorized Rainbow dealer and let them replace it.\015\012If your rainbow is still under warranty, replacing th belt yourself will void any warranty there may be. ... Rainbow E series Canister Wet/Dry Vacuum

When using the vacuum cleaner,the whisper belt floor cleaner acts as if it is being robbed of power when it is being pulled towards the operator. It is almost as if it has a short in the wiring harness. Can anyone help me with this?

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Dyson DC05 It is a vaccum cleaner in a perfect condition but recently developed a problem. It sparks and sometimes power goes off while operating. It is clear that the wire is loose but do not know how to open the bracket of the main button on the machine. [email protected]

Hi \015\012try this site http://dysonmanuals.llc.nu/\015\012\015\012It has service manuals for the DC05. ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0922 seconds