Having problems with your Vacuums ?

Roller is not going around. Is there a way to get it out?


Answers :

What kind of vacuum do you own?
\015\012Usually there will be 2-5 screws on the bottom holding the plate around the spinner to the base. Use the appropriate screw driver and remove those screws. Next remove that face plate.
\015\012Once open you most like see that your belt broken. If that is the case, you can either take the belt it's self to a vacume shop; or get the information off of the belt and pick up a replacement at most retail super stores.
\015\012Once you have the belt, slip one end around the dowl looking thing. This is located under the roller area. Then, insert the roller in the end opposite the belt.
\015\012Now's the difficult part; you must stretch that tiny belt around the roller and click the roller in place.
\015\012Please update me once you have gotten that far, or if you have any other issues. :-)
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!


First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

Roller is not going around. Is there a way to get it out?


What kind of vacuum do you own? \015\012Usually there will be 2-5 screws on the bottom holding the plate around the spinner to the base. Use the appropriate screw driver and remove those screws. Next remove that face plate.\015\012Once op ... Vacuums

I can't turn the belt off of my Kirby vacuum. I had the front off of it earlier to attach the hose, but now when I put the front back on, I can't get the belt to turn off. The lever twists about 3/4 of the way around, but will not go the rest of the way.


Turn the front part to the green so it is level and then twist the front to the red make sure the belt catch the hook as you twist it then if the belt is hooked just put it back on the vac like normal and lock it in place then twist it back to the gr ... Kirby Ultimate G Bagged Upright Vacuum

I have an old Royal upright & can't get the roller off. It was not going around & I was trying to see what was going on. The belt still seems OK.


The belt may seem okay, but if it has stretched too much to get a good grip, it will slip around the shaft and/or brush. Replace it and see if that helps. ... Royal Vacuums

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

I have a sta rite (pentair) cristal high rate sand filter model T-200-BP-1....its leaking water thru the top of the valve, where the valve cover screws on the valve body assembly. it leaks water out where they go together around the screws. Also when i vacuum it, everything that i vacuum gets washed back in the pool when its on the filter position. Also the backwash leaks when its turned 2 the filter position, does it supposed to do that?...the only way i have gotten it to stop is to put a seper


... Vacuums

My belt broke...I bought a new belt..but I do not know how to put the new on on. I took out the brush roller and put the belt around it but I have no idea how to get it to go on the part that makes it move.


Hello,\015\012Here is a link to my free online guide...\015\012\015\012http://reviews ... Kirby Ultimate G Bagged Upright Vacuum

THE ROLLER WON'T GO AROUND. THE EXTRA ATTACHMENT WORK WELL, BUT THE ROLLER STOPPED GOING AROUND.


HI There,This is definitely a problem with your belts. This Hoover Windtunnel Self-Propelled models has a poorly designed belt system that frequently goes bad. Most customers will have to replace the belt once every 8-12 months, some ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?


I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Cant seem to get the green light going on vacuum head,hook seems to be wrong way when its should be hooking the band off its doing the opposite


1)First, you turn the square belt lifter on the front of the power nozzle until the red arrows line up (belt off)2)Remove the power head from the front of the machine. Now turn the belt lifter the other way and line the green arrows up ag ... Kirby Ultimate G Bagged Upright Vacuum

How do I replace the belt on a Bissel Powerlifter rug shampooer? I have removed the door that is marked "access belts". The problem is that I don't see how to get the belt around the lower roller. There is no problem getting the belt around the upper prong. Please advise.


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Hi There I have got a Kirby 2 HG vaccum cleaner which is around 20 years old now. It was going really well until last week when one of the capacitors which are connected to the brushes blew up. There is two capacitors one for each brush. One of them completely blew to bits and the other one is still intact. My question is are they the same size and where do I get a new one from. I know it is an old machine, but I would like to fix it and get it going again. Any tips???


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=541405\015\012Generic problem for all Vacuums\015\012Hi There I have got a\015\012Posted by opfinder on Apr 24, ... Vacuums

Cord rewind The power cord is jammed and won't go in or out. I can't find a way to get the cover off to have a look at it. Any suggestions please? Power cord jammed won't go in or out. Can comeone tell me how to undo the casing to get to the power cord?


Which model do you have.. ... Vacuums

My Janome Harmony 8100 will occasionally stop and give me a System Error #1 - I cannot find anything about this error. It is a computerized machine with 70 stiches and attachable embroidery hoop. I first started getting this error with the hoop and now get it when I am just sewing. As soon as the needle goes down to the bobbin, I get the error. The machine freezes and the only way to get rid of the error is to turn the machine off. Sometimes I can get the machine going again, but now it wil


... Vacuums

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?


If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums

I need to put my kenmore vaccum back together I took apart the lower unit to get the roller it got gunky and all around the roller got gunky, Now it;s a bear to put back together


Remember the last thing you took off and start there,work your way in reverse towards the first thing you took off ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a bissell bagless easy vac. When I vacuum the debris keeps getting stuck in the hose (also going into the filter area and the apparatus above the cannister with none of it going into the cannister. I have made sure the cannister is properly placed and the lock is pushed in all the way.


... Bissell 3102-0 EasyVac Upright Vacuum

Hello! I have a problem with my Tefal Sensio scales. They are now probably around four years' old and have been in perfect working order up to now. Well, I had some problems before - the moment I'd step on them, instead of going into "calculating mode" as they usually do, they would show the number 92 straight away and then the display would change into some strange symbols (please don't laugh here :-) - my weight in kg is 55, my husband's around 80 and each of us gets 92 reading). Previo


... Vacuums

I can not get the water, normal heavy traffic selector reinstalled after taking unit apart, i replaced the pump, and now i cannot get it back together, there seems to be a special way it goes together, and i'm not finding it. Are there any videos, or pictures that show how it should go back together?


... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

No suction Just received my refurb. dyson animal bagless. Finally figured out how to get it all together, turned it on and there is no suction coming up thru the beater bar. The hair is just collecting around the bar and not going up into the canister. It appears all the suction is going thru the open red end of the attachment hose, which has a vented cover piece. Am I missing a piece or is there a switch to turn of the attachment suction?


So the red hose isn't connected to a part on the vaccum so like it is connected to the connester but not to an opening just above the beater bar, this is the only idea i can supply you with. good luck, maybe i got lucky and helped you out. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Is the roller suppose to continously go around when running? Doesn't seem to change mat in carpet when going over it. Doesn't seem to be much suction..


The roller should be rolling whenever the vacuum is running unless you have a fancy vacuum that has a switch for bare floor that stops the roller.if your roller is not running then most likely the belt is broken (does it turn very easily ... Vacuums

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Shampoo-er This seems to be a common problem, the shampooer is putting out alot of water and hardly any suds. I read through the posts about the little filter that sometimes gets out of place and I think I found it in the box - is it about 1" diameter hard plastic ring around very fine mesh? If so where exactly does it go? Some posts say in the hose, and others say in the opening of the tank. Or does it go in the place where the hose attaches to the tray? I also found a round sponge in the box o


It goes on the small hole on the tank where the hose attaches to it. The sponge goes in the hole directly under the on/off valve. Here is a link to my online shampooer instructions.\015\012 \015\012 ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0740 seconds