Having problems with your Vacuums ?

Shop-vac model 90L550A motor wont run

\015 I have a shop-vac model 90L550A shop vac. The motor no longer runs when I plug the cord into the outlet. I removed the motor from the vac itself and took notice to a yellow plastic piece that had a wire going into it and one coming off it. Inside I found a melted metal piece. I am assuming this is a fusible link that obviously melted and broke the circuit. I was wondering if there was something I could do to make this work again, maybe placing another fusible link in?\015

Answers :

Yes replacing the link would work, but that would not fix the cause. You have either pulled the wiring to the point of pulling apart the connection or there is a short. Which would be in the way of a grounding effect causing the link to heat and melt. A safty issue to be sure. Check all contact with housing and motor to make sure there is not an underlying problem to start with. Unpluged of course
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Shop-vac model 90L550A motor wont run


Yes replacing the link would work, but that would not fix the cause. You have either pulled the wiring to the point of pulling apart the connection or there is a short. Which would be in the way of a grounding effect causing the link to heat and melt ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

I have a ten year old M+S central vac. it shuts off after about 5 min of use. They came out and took the unit to their shop. I dont have the model #.repair shop says I need a new motor but it runs. what can I tell them?


... M&S Systems FX-3000 Bagged Central System Vacuum

Need a manual for the shop vac model # 2E200 - Shop Vac Shop-Vac& Mini Hang Up Wet/Dry Vac Vacuum


... Shop Vac Shop-Vac& Mini Hang Up Wet/Dry Vac Vacuum

Shop vac model 3331.5 H owner manual - Shop Vac 333-32-08 Blower Vac Wet/Dry Vacuum


... Shop Vac 333-32-08 Blower Vac Wet/Dry Vacuum

Switch for Shop-Vac model QPL650 - Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

Manual Shop Vac Shop-Vac& Mini Hang Up Wet/Dry...Model 2015A


... Shop Vac Shop-Vac& Mini Hang Up Wet/Dry Vac Vacuum

Shop vac mini model #2010A - Shop Vac 584-06-00 Canister Wet/Dry Vacuum


... Shop Vac 584-06-00 Canister Wet/Dry Vacuum

My shop vac will not turn on. model 87L400 - Shop Vac Vacuums


... Shop Vac Vacuums

Bought a shop vac about 3-4 mos ago and while i was using it, it cut off and wont cut back on. This is the second shop vac that done this and I took the first one back and got this one and it did the same thing. It is a 12 gal. 4.5 peak hp.


... Shop Vac 401-12-00 Wet/Dry Vacuum

Need user's manual for Shop-Vac model QS 30 - Shop Vac Vacuums


... Shop Vac Vacuums

Attach hose to shop vac model j150a - Shop Vac 201-13 Wet/Dry Vacuum


... Shop Vac 201-13 Wet/Dry Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

I have a Shop Vac (Wet/Dry) Model 5275 (120V 60Hz 6.4A), Peak HP of 2.75 While vacuuming the Shop Vac fell over, stopped working, and would not come back on again. Tried plugging into another outlet, etc., but nothing works. Is there some internal problem that I can fix myself?


... Shop Vac Vacuums

Shop-vac model 500A 52713-75 - Shop Vac Vacuums


What is the problem ?God bless youif if suction, test the hose blockage 2) belt drive is worn 3) power brush dirty, clean or replace, 4) test the motor for repair, clean, and lube.see the diagram ... Shop Vac Vacuums

I have an old Shop Vac model 3331.5. This is a 12 gallon 1.5 hight peak shop vac with a detachable blower. After many years I decided to use the blower feature, but have lost the lost the manual. Question; how do I attach the hoses to the blower? The motor has that cap on it the direct the flow of air in one direction and the wide hoses do not fit over it. I may be missing a part, but I would think the directional cap would have to come off anyway.


Remove the cap that directs the air and insert the hose in there. ... Vacuums

Shop vac model 800m manual - Shop Vac 925-09-62 QSP Plus Wet/Dry Vacuum


... Shop Vac 925-09-62 QSP Plus Wet/Dry Vacuum

I have a craftman shop vac model 500A , 5GAL.,1.25hp. why does Sears say that's not the model num. IT'S THE ONLY MODEL NUM. ON IT!!! IF IT'S AN OLD MODEL,WHY DONT THEY SAY IT IS THE SAME AS MODEL#***** AND WHY DOESEN'T THE FILTER,BAG'S ect.SAY, WILL ALSO FIT MODEL 500A


... Craftsman 17765 Canister Wet/Dry Vacuum

Wet/Dry Shop vac Model BMB200 manual


... Shop Vac 584-06-00 Canister Wet/Dry Vacuum

SHOP VAC MODEL 84L850


... Shop Vac 201-13 Wet/Dry Vacuum

Shop-vac model 90m300 switch bad


... Vacuums

Vacuuming up water with Shop Vac model 84M200


When picking up dry materials use the foam sleeve that slips on and the blue cloth (assuming there all blue) over it, there should be a ring that slides over blue cloth to hold it in place over the foam sleeve, for wet pick up u can use the foam slee ... Shop Vac 84M200 Wet/Dry Vacuum

Owners manual for a Shop-vac model QUMP600


... Shop Vac Vacuums

I need a user's manual for Shop-Vac model 90L650A


... Vacuums

Change shop Vac Model LM500 from dry to wet pick


To change from dry to wet, remove the paper filter and install ball float if not already attatched ... Shop Vac 925-13 Canister Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0925 seconds