Having problems with your Vacuums ?

Aquavac runs for short time then cuts out blowing the RCD . Have rewired mains cable thinking a broken or loose wire... still same problem. Have also noticed that a lot of sparks etc coming from the motor brushes. Vac approx 10-15yrs old.Aquavac is model 6310B


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Aquavac runs for short time then cuts out blowing the RCD . Have rewired mains cable thinking a broken or loose wire... still same problem. Have also noticed that a lot of sparks etc coming from the motor brushes. Vac approx 10-15yrs old.Aquavac is model 6310B


... Vacuums

We own a dirt devil model 088600, and are experiencing a problem with the belt wearing away a section between where the belt connects to the brushes and the motor. There is a lot of plastic/rubber residue coming out from the vacuum. We have tried new belts only to find the same problem occurs. I noticed that the source of the dust is coming from the section between the brushes and motor, where there appears to be a section that is misshapen and melted. I looked up the schematic online and can't


If you are certain that the belt is seated correctly and the beater bar is nested in its holder and the cover of the assembly has been properly installed and you still see a contact area between the belt and cover, you should either: return the vac ... Dirt Devil Vacuums

I have a Hoover, Steam spin scrub, Model F5897-900. Only used it a couple times and the motor gave out. First started being noisy then a bad smell. It did seem noisier that what I would expect from the start but I didn't realize it was a problem with the shaft of the motor. I took it apart and found the motor shaft wasn't true and causing sparks. The motor looks like it can not be taken apart and repaired. This seems like a default from the beginning but it is past warranty. Also noti


You will have to replace the motor and the hose asm. thehooverstore.com may be able to help, or you should be able to find a repair shop that can order them for you. ... Vacuums

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on


... Miele Blue Moon Bagged Canister Vacuum

After using switch to go from floor to carpet, noticed the roller brush not working, and therefore the self-propelled feature also not working. Replaced what I thought was the problem, a loose belt, but still does not work. Motor runs and there is suction...???


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I HAD MY DC17 VAC FOR 3 YRS NOW NO PROBLEMS AT ALL, I REGULARLY CLEAN THE FILTER LIKE IT SAYS BUT LATELY I'VE NOTICE THAT THERE SEEMS TO BE A LOT MORE COLLECTION ON THE TOP OF THE FILTER WHEN I'M DONE VACUUMING. IT HAS ALSO STARTED THIS WEEK TO MAKE A VERY LOUD HUMMING TYPE NOISE WHILE RUNNING, I HAVE CHECKED FOR ALL POINTS FOR ANY BLOCK AND NOTHING AND NOW TODAY IT RUN A FEW MINUTES AND STOPS AUTOMATICALLY,IT WILL RESTART AFTER I LET IT SIT UNPLUGGED.WHATS UP WITH THIS THING, IT HAS BEEN GR


The vac is over heating. First, you should try a new filter. Also, keep in mind that after cleaning the filter, make sure that it fully dries. Using a wet or damp filter clogs it quickly. Second, turn the vac upside down and make sure that the roller ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Kirby G 2001 upright vacuum wont turn on. I tried another outlet and still nothing. I don't see a breaker switch anywhere. If you know of any common problems I would love to hear them. I am very mechanically inclined, I just was wondering if there are any common issues with the motors or power switches etc. so I don't waste a lot of time troubleshooting. Thanks


This might sound a bit silly but check to see if the cord is plugged into the machine correctly if it is check to see if the safety interlocks are all engaged. ... Vacuums

A problem. There is this littille mechanism on the top of my rainbow E vacume motor it is making a lot of sparks when it spins and there are two peices that have springs in them that are pushing like two flints i think. that are tuching the spinning thing. as you can tell i dont know what any af this stuff is called so please work with me.


Sounds like the carbon brushes. If they are sparkng, then either they are bad or the armature is bad, possibly both. ... Rainbow E series Canister Wet/Dry Vacuum

My vacuum motor started to smell "hot" and sound like it was struggling. Also not a lot of suction. Could there be an obstruction? The bag is new and the performance light isn't coming on.


Hi,Here is a tip that I wrote about my Bissel but I bet you have the same problem and the hose is clogged...Bissell Bagless Upright Vacuum not ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Low suction Have a Powr-Flite PF 18, suction is good at motor, but low at where hose comes out of top of vacuum. Could new lid seals help the problem? Where can I get new seals for this model. Also my zip is 98801 and my shop is not listed, could you add it please? Sew Creative 1139 N. Princeton Wenatchee, Wa 98801 509-663-5516 Thanks, Lauren-Sew Creative


Replacing the motor cover solved the problem, it must have been warped and was letting suction out thru it. ... Vacuums

Belt drive Not only do I need a PN for the drive belt on the Panasonic MC-V7395 Vacuum Cleaner, I've noticed that there are problems with the belt breaking. Can someone also explain the proper way to install the belt over and around the motor spindles and any other information that may help. Thank you.


Http://www.partstore.com/Model/Matsushita/Panasonic/MCV7395.aspx?SearchTerm=True ... Panasonic MC-V7395 Vacuum

Burned out The best way for me to describe the problem is to post reviews I made on Amazon.com, which is where I purchased them. ________________ Based on my past experience, I bought another 6 months ago. I live in a very tiny 2 room apartment and do not vacuum lots of dirt. I noticed this new vac getting very hot to the touch where the motor is located with only a few minutes of use. Today it just STOPPED. When I felt the canister, it was HOT. It obviously has burned out. Upon closer inspect


... Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

I have a Nutone CV-450. When the unit is turned on the motor makes a high pitched whining sound. The suction seems like it is reduced and there is a burning rubber smell coming from the unit. Suction at the unit itself is also reduced. Any ideas about the cause of the problem and the solution?


... Broan-NuTone CV450 Central Bagged Central System Vacuum

Electrical problem The light comes on but the motor will not come on when the on button is pressed. Is there a reset button? I thought it was because the bag was full but I just changed the bag and the motor still will not come on.


The light is separate from motor. No reset switch. Check for a fuse but i suspect it may be brushes are worn out and not making contact.Sometimes that starts as an intermittent.Hopefully one of the coils isn't open circuited. ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Sparks from the Kirby Motor


1. Do you think this may be the problem?YES\015\0122. How come it continues to rotate? ... Kirby Ultimate G Bagged Upright Vacuum

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.


... Bissell Vacuums

Hello can you help me please? I have a Kirby G4 vacuum cleaner, It did work ok until it started to give off burning smell and lots of sparks from the brushes. I have changed these brushes, the motor still rotates but it still gives off sparks and burning smell. Do i have to change the motor as well? Can you help please? Thankyou Martin


Some debris, even sand or dirt, probably got into the motor, causing damage to the armature. If this is the case, you will need to replace the motor. The burning smell from the motor is generally a sure sign of a bad motor. ... Kirby G4 Bagged Upright Vacuum

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current


I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum

Sparks coming from under oreck vacuum. looks like its coming from motor brushes.


Probably need to have that serviced at a repair shop. They can tell you whether or not you need a new motor or a fan blade kit. ... Oreck XL Ultra Bagged Upright Vacuum

Recently my central vac system started making a louder than usual and laboured sound when in uise, enough so that I took note and inspected the canister and motor while running. The motor was trowing off blue sparks and looked like it could 'POP' at any moment. I will not risk using it until I know what the problem is and how to repair it. My assumption is the motor needs to be replaced. The system came with the resale house I bought 3 yrs ago but I do not know the age of the system itself.


... Vacuums

Dead motor? My 8 year old Miele S251i has worked fine, until I was recently vacuuming and moved the plug from one outlet to another. When I restarted the vacuum, it made rrrrr.....rrrrrr....rrrrr noises and smelled like something was burning. I turned it off, and it's shown no signs of life since. Sound like a motor problem? I've taken the cover off and looked at the cord and seen the motor, nothing looks obviously wrong, but I'm also not mechanical.


... Miele S251 Flamenco II Bagged Canister Vacuum

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t


... Vacuums

Motor problem When i plug my steam vac in the motor sparks and smokes. It smells as if the motor is burning out. I've tried different outlets through out the house and get the same outcome, what can i do to solve this?


Nothing you can do im affraid its the motor armature so unless it can be stripped down then you will need to replace the motor i would get a price for the motor to decide if it is worth doin sorry. ... Vacuums

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther


... Clarke Vacuums

We bought a Philips Intellicare 8030 ironinng system in 2005. Two days ago water from the plastic water container does not go inside bigger water tank where we think the water gets heated up. When the heating tank is empty there is no steam that comes out of the iron. Also, there is water dripping off profusely from under the iron where the steam normally comes out. Can you please advise how we should remedy this problem Please advise which service centre in Sydney, Australia would we be able to


... Philips Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0698 seconds