Having problems with your Vacuums ?

I have a light ballast that stopped working. The lights around this one bulb still work but changing the light bulb did not fix the problem. Any idea what is going on here?

Answers :

The ballast is like a fuse and the ballast is blown .
\015\012you will need to replace the ballast as it will let current thru for some bulbs but not enough to light them all up.
\015\012also if you use old bulbs that are alomst blown and new ones it puts ware on the ballast and it wont last as long.
\015\012if you do not know how to change the ballast you should get an electrician in to do it for you. he could also look for other problems and better detect the issue you are having.
\015\012however i find that replacing the ballast is usulally the easiest fix.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a light ballast that stopped working. The lights around this one bulb still work but changing the light bulb did not fix the problem. Any idea what is going on here?

The ballast is like a fuse and the ballast is blown .\015\012you will need to replace the ballast as it will let current thru for some bulbs but not enough to light them all up.\015\012also if you use old bulbs that are alomst blown and n ... Vacuums

Power nozzle of my S3670 does not work (vacuum itself does work), the headlight bulb in the nozzle is broken. This happened in the past several times - we would bring the vacuum to service center - I don't know what they did other than replacing the bulb. I decided to go to ACE and buy replacement bulb myself, replaced the one in the nozzle - this did not fix the problem. I don't see any fuzes or anything in the nozzle. However, the manuals says to "Use only HOOVER part no. 27317307, which is a

... Hoover S3670 Bagged Canister Vacuum

I have a ge light switch receiver rf1023, with incandescent bulbs, and when I try to switch it on it just blinks once and goes out. if I hold the switch on the battery-operated wall remote, the lights keep blinking until I let go. It used to work fine, and now it doesn't. I've lost the intallation instructions, so I don't know if there was a trouble-shooting section that covered the problem.

... GE Vacuums

I have 2 mood lights (90843C - 925600010602) within 2 weeks of each other, when switched on they light up for under a minute and then go off. I have tried them in various sockets around the house to ensure it isn't a problem with the socket. Any ideas ? Thanks, Jan

... Vacuums

Hello. My scooba 5800 had a check tank light on. I used a straw on the valve and that fixed the problem. Now the scooba runs like nothing is wrong, but there is no actual cleaning going on! It goes the full cycle, but no liquid comes out. The vac part seems to be working b/c there is fluff in the vac when it's done. Please help!

Hello, Take the battery out and hold the switch down for 30 seconds, to reset the curcuit board, then charge back up for 12 hours. this should take care of it. If I can help future please call @ 1561-848-3387 Thank you, Teresa. Clean Sweep Vacuums ... iRobot 5800 Scooba Vacuum

HI, I have a Kenmore 25813 and it seems like there is an intermittent short. When I have the extension wand on and the power floor attachment on, when it rotate the wand the light cuts out and so does the power floor attachment, when I twist it back it comes on again. I don't have this problem if I remove the wand and just use the crevice tool with the hose. Any idea where the short might be and can I fix it myself? Thanks. Gary

This is common you may have a short in the contacts from the handle to the wand or a break in the cord that goes into the powerhead ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum

I have a Dirt Devil Vision and when I put a clean canister back in place the suction at the bottom of the filter clogs up and very rarely go into the canister. Also where the air blows out of the motor, I will get particals that will blow out. I have checked where the belt is and also the suction tube. Do you have any ideas how to fix this problem?

Yes your intake hose is clogged thats the clear hose you can see it on the bottom from the back.disconnect the upper hose from your intake hose and try to push a coat hanger through with the end of the coat hangers end bent till its rounded so you do ... Dirt Devil M086700 Vision Bagless Upright Vacuum

I was changing a light bulb with one of those metal extension rods that unscrew and screw back in the replacement bulbs. It evidently didn't seat correctly and pulled off the bulb and created a quick "poof" type electrical short. I have switched out that bad bulb with a new one and can't get either the fan or lights to work. There doesn't appear to be a reset switch. I also swirched out the wall switch to see if that would make a difference and it does not. Any thoughts or ideas would be appreci

If you have not already done so, I would check at the fuse or circuit breaker panel to see if you have blown a fuse or tripped a breaker. ... Vacuums

Eureka Model C2094-Type GW Vacuum 1 Bags-Belt- Beater Roller or bristles that go on roller-light bulb Vacuum 2 Bags-Belt-Beater Roller-Bulb-Plastic frame the motor bolts on-Metal holder the handle go in that lets the handle move up and down

... Eureka Vacuums

I have a ceiling light with a holgen bulb that I cannot figure out how to change. The fixture has an outer ring against the ceiling and an inner ring that has the light. The inner ring tilts. I have not idea how to get into it to change the light!

From what I know you are suppose to change the whole thing. ... Alto 302000414 Attix 8 AS/E Canister Wet/Dry Vacuum

I have a coralife aqualight model 53008. It uses two 65watt compact bulbs. The whole light quit working one day. I tested the bulbs in another aqualight I have and the bulbs were fine. I want to know where the ballast is. I opened up the ends and the wires are so secure I cannot pull on them to locate a ballast. Please advise if this is a ballast problem and how do I replace it. Thanks Linda

... Vacuums

Euro-pro iron. red light on. green light blinks on but iron will not heat up. lights do not progress through yellow (does not go past green) purchased from walmart with warranty extention on 12/08. Never had a problem before--what is wrong.

The inner grid that heats up the iron has an open which will not give continuity to heat the iron up. These grids are not serviced so more than likely a replacement iron will be on your list to purchase ... Vacuums

Over heating Light Comes on as soon as I try to turn the unit on. I have a Miele S558 Silver Moon vacuum that has only been used once and it shut off and will not come back on. The overheating light comes on as soon as I try to switch speeds on the handle or turn the unit on at the canister, and the vacuum will not run. Do you have any idea what the problem is?

... Miele s558 Silver Moon Vacuum

After a brief power outage my Marantec 4700 garage door opener has problems opening/closing. When opening it stops at the fully open position and the lights blink, when closing it automatically reverses just as it fully closes and then the lights start to blink again. I checked for obstructions and tried to reset the limits of travel per the manual, it still does the same thing. Any ideas on what to try next?

This is not a sensor issue, I have a similar problem, sensors work fine, garage door is still fully functional, all operations, including safety sensors work properly, just the overhead lights flash. I suspect there was damage to the power board due ... Vacuums

After two years, my Euro-Pro Shark Steam Mop, Model S3101, no longer ejects steam. I have used tap water. I think the line is clogged with mineral deposits. The light is on when plugged in, and the unit heats up. I even put in vinegar for about an hour to break up the calcium deposits, but it did not correct the problem. How do I fix it, or, where can I take it locally to be fixed (Orange County, CA)?

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Have an lg Hoover and the red light on the handle keeps flashing and the blue light on the Hoover is also flashing and then it cuts out. Has little suction with the head on it but better when you take it off. How do I fix the problem?

... Vacuums

I have a FoodSaver 3840 and have been happy with it for some time now. I clean it frequently and have had no problems. The Tray Full light came on after sealing some Christmas ham. I cleaned the trays, as I had done many times before, but now the Tray Full light will not go off and my FoodSavor does not work. Any suggestions?

... Vacuums

My Miele vacuum cleaner has the red triangle light on and keeps switching on and off. Is it broken? have been hoovering upstairs and I noticed the hoover had the red triangle light on. I changed the hoover bag but it still kept going on and off. Is this an overheating problem or is the hoover on the way out?

... Miele Vacuums

Hoover bagless cannister 3765 - belt on power head slips off spindle. bought new belts - same problem. is this a design problem or can it be fixed? I don't want to take it to a repair shop 100 miles away and have them just put on a new belt. saw idea of smaller belt - what number? couldn't find suggested royal 104425001 belt.

I would not recommend a smaller belt. You will only wear the motor. This model series power nozzle needs to have a metal clip installed near the belt on the brush roller housing. I know that most of them left the factory without it. Remove the cover ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.

The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum

I have a Morplan Vitesse 1600w steamer. When switched on the steamer doesn't heat up, only a red light flashes on the steam level lights. Any idea what could be the problem?

Check the water lvel in the steamer, if there is water then take the unit to a repair shop for a checkup. ... Vacuums

Dirt finder I have a Hoover U6439-900.  After the cleaner was used a few times, the dirt finder light cycles between green and red on the regular setting and will not go to green.  On the sensitive setting, the red light stays on most of the time.  I have tried to run the cleaner to remove any dirt but have not solved the problem.

The sensor may be bad, or it may be coated over with dirt. Re,ove the hose at the back of the vacuum, the head of the sensor is down inside that opening, reach in there and clean it off and see it that corrects the problem, if not replace the sensor ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The retractable cord is stuck all the way out and will not go back in. Is there a simple way to fix this "disaster"??? without taking vacuum apart that is. And this is not my exact vacuum but I figure the cord problem would go for all of them. Ours is a ORANGE HEPA 360 Kenmore Whisper Belt 12 amp with PowerMate Model # 116.29219800

... Kenmore 27915 Bagged Canister Vacuum

I have a Simplicity Vacuum-4800. I bought new filters and a new light bulb, but don't know how/ where to go to replace them... HELP

... Eureka 4874 Bagged Upright Vacuum

My 400 series Discovery Roomba will no longer charge. It shows a green "charged" light, but when I hit clean, all lights/vacuum, etc just go out and it stops. Irobot says that the entire unit needs to be replaced, but it has to have something to do with the charging mechanism. Any Ideas? I've tried the system reset, and removing/replacing the battery. No effect. The robot doesn't give me the "uh-oh" beeps to be charged. It just stops and goes dead.

... Roomba Robotic Floor Bagless Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0588 seconds