Having problems with your Vacuums ?

What type of tool do I need to open up the bottom of the Cuisinart DBG-550BCHWS? My on/off and digital clock lights are flashing when I plug the coffee maker in and the maker doesn't not work. I have tried opening and re-closing all compartment doors. Thanks for your help.


Answers :

Screws are Torqux Tamper-proof/Safety screws size T-10. It's a Torqux \015\012screw with a raised middle requiring a special Torqux wrench. You can buy a T-Handle set at Sears for $35.
\015\012
\015\012http://www.tamperproof.com/
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

What type of tool do I need to open up the bottom of the Cuisinart DBG-550BCHWS? My on/off and digital clock lights are flashing when I plug the coffee maker in and the maker doesn't not work. I have tried opening and re-closing all compartment doors. Thanks for your help.


Screws are Torqux Tamper-proof/Safety screws size T-10. It's a Torqux \015\012screw with a raised middle requiring a special Torqux wrench. You can buy a T-Handle set at Sears for $35.\015\012\015\012 ... Vacuums

After a brief power outage my Marantec 4700 garage door opener has problems opening/closing. When opening it stops at the fully open position and the lights blink, when closing it automatically reverses just as it fully closes and then the lights start to blink again. I checked for obstructions and tried to reset the limits of travel per the manual, it still does the same thing. Any ideas on what to try next?


This is not a sensor issue, I have a similar problem, sensors work fine, garage door is still fully functional, all operations, including safety sensors work properly, just the overhead lights flash. I suspect there was damage to the power board due ... Vacuums

I have a Chamberlain Liftmaster Professional 1/3 hp garage door opener. I'm unable to find the model number, but it was made in April 2004 and has an orange learn button. It has been working fine since it was new, but now will not open or close when the code is entered on the touch pad. When the problem first started the door would close, but not open. I have tried to reprogram a new digital code, but it does not work at all. There are no problems when opening or closing the door with the re


... Vacuums

My garage door opener will start to close then stop and go back to the open position. If I put pressure on the door as it is closing sometimes it will close all the way and sometimes it will return to the open position. Can you help me. Thanks


Sounds like the pressure sensor is being tripped - this is a safety feature on most makes in the last 10 years.Find the make/model of your device and it probably has some knobs on the main unit to adjust. For example, on the ... Vacuums

I have a craftsman garage door opener remote control model TX2028 139.18191. The remote stopped opening or closing the garage door. I replaced the battery and tried to re-program it through the LEARN button as per the manual of the Garage 1/2 HP opener. The process has failed after several trials and the remote is still not working. Is there anything else that I can try or should I get a new remote. Thank you


... Vacuums

I just bought a Samsonite "Freeminder Flex" backpack with handle. My issue is with the lock... The combination for this lock was set to open at 0-0-0. It opened and locked perfectly at first. But after following the instruction to set up the new combination code, it doesnt lock anymore....please help and thanks! Linda


... Vacuums

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

My Shop-Vac 5870400 was working just fine, and then one day while i vac the floor its just stop working, tried to turn on/off a few times, swicth to different outlet. i did even tried to open it, but found no burn or anything that suspicious. i never drop nor used outside, only inside the house for normal vacumm. please help. thanks.


Same thing just happened to mine. My solution is to get another one but a different brand. I think it should have lasted longer than four years of fairly light usage. From what I read, if it does as we both described, the motor is shot and not wor ... Shop Vac 587-04-00 Canister Wet/Dry Vacuum

Dyson DC 14 hose has no suction, with or without brush attachments. Hot air shoots out from the base of the canister when I try to use the hose. I cleaned the top filter, but can't figure out how to remove the hepa filter to clean it without destroying the case. It looks like it might take three hands to insert pennies and "flip" the case open as is suggested on a youtube video for a different model. Would this even help, assuming I could get the thing open?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I can't open it to clean it, please help! I know I have to pull the grey cover, and I have tried hard but no luck. Seems attached from the bottom, so I am not sure how it will come out. Thank you for your help.


I had the same problem. It normally opens with a little tug on the door but if you are like me and you let it fill up with a year's worth of pet hair etc., the door will jam. The only option is to ... SweepEZE 600 C-1 Canister Vacuum

I'm trying to get my S7000 Miele to stand upright an lock in this position. It wont , i tried to see if foot release was jammed but cant tell it doesnt seem to release to let it move upright an lock in again..help


There is a rear dust cover that sometimes gets stuck, this will make it almost impossible to lock the handle up. First locate the cover which is at the rear right above the wheels. It's about 2"x8" and ribbed vertically and slides up behind the rear ... Miele S7210 Bagged Upright Vacuum

I have a new bissell 50c9 upright vacuum and it keeps clogging in the clear window in the back. there is a flap that keeps coming open and filling up. everytime i clean and restart, the flap opens. i tried holding it closed and noticed lose of suction.


... Vacuums

I have singer fashion maker 2818. The problem is the bobin casing (the one which holds the bobin)is coming out (i.e) loose. trying to fix it in place but not sucessful. can someone explain how to open and fix the case and place the other supporting covering so that there is smooth motion of the needle and the bobin.


... Singer Vacuums

I have a worn clip - the open close clip to secure the adjustable handle in place. I have the new part but, not sure how to fit it. Can you help?


Yes. Remove the handle and cable, then remove the bag compartment cover. At the back of the bag compartment, towards the top, you will see four screws. Ignore the one furthest to the left, and unscrew the other three. That will release the cover at t ... Sebo X4 Bagged Upright Vacuum

Rival model CM1100 coffee maker: I can not get the coffee carafe in the right position. Should it lock in? Sometimes the coffee does not enter the pot and overflows onto the counter. Should the handle be on the left or the right or maybe the center? Please help me. I am not a coffee drinker and when I try to serve it to friends, I end up with an embarassing mess.


... Vacuums

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet


Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My electric toothbrush doesnt work any more even though I have only used it a dozen times. I have obviously tried to charge it, but with no result.I disposed of all the packaging when I started using it so I dont have the guarantee. I bought it from Tesco in Roundhay Rd., Leeds 8. roun about Christmas time. I would be grateful if you could help me with this matter. Yours sincerely, Mrs. L.E.Glenn


My Dear Chap. It is highly unlikely that you can exercise any type of warrenty for the toothbrush without the documentation. That is, a reciept at the least. Packaging would have helped, but the receipt is the key.\012What you can do is try to ... Vacuums

I'm trying to change the filter....One person told me to open the hose end and take the bag out and go from there, but that isn't the right way!!! It's the other end where a couple brushes are able to be stored on top of the canister, but I can't figure out how to get that section off..it's as tight as a drum HELP PLEASE and thanks. Betty


There's a tab at the middle of the lower back of the tool holder (air diffuser). Pressing in on that tab should enable you to lift the back of the holder first, then lift off the whole thing. It will come off, just make sure the tab is in far enoug ... Electrolux Epic 6500 Vacuum

Sounds dumb but have my grand-daughters laptop and cannot figure how to put dvd in it to watch,. do not know how to open and close tray. please help. laptop is a dell studio


Hi, Switch on Laptop. \012On the side of the laptop is a compartment. Place on table, look both sides, on one of the sides there will be a small push button, slight pressure, remove finger, and drive will "POP" out. ... Vacuums

My honeywell hht-149-hd is not oscillating properly. it will rotate less than a full rotation then stop. the motor is still trying to turn the tower because i hear a rhythmic clicking inside the unit. i don't want to pry it open and void the warranty unless there is an easy fix. please help. thanks!


... Vacuums

Have a Genie 2020L garage door opener. Door start to go down then stop and return. Tried cleaner old sensors. Same. Noticed red light on sensor 3blinks then off....repeat constantly. Replaced sensors - same issue. Reset unit...checked all wiring...no jams anywhere.... HELP PLEASE L:-)


... Vacuums

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis


Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums

Canister problem When I lift the canister off to empty it, the flap at the bottom swings open, depositing 3 dog's worth of hair on my foot! The flap won't stay closed - even after I cleaned off the seal. HELP ME! Please.


Check that the plastic piece isn't broken. I had to replace my canister once because the little detent where the clip holds the base down was bent out of shape. It's too fragile to bend...just replace it. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson Animal upright (purple). I took it apart to clean the cyclone chambers. When re-assembling the bottom closed before the opening rod was inserted. I can't get the opening rod installed with the bottom opening closed. How do I open it? Thanks.


I looked in our DC07. I would try removing the top again and getting a long dowel or the opening rod, insert it down into the unit and PUSH. The opening rod opens the latch by pushing it, not pulling it. Here are some pictures of the latch. Top pi ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have an older Blue Max screwdrive. No safety beam on this model. The door will not close with the remote or wired switch. Press = door opens. press = nothing. press = door opens. press = nothing. With latch lever pulled door will open and close easily.


... Genie Company Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0681 seconds