Having problems with your Vacuums ?

How do I get bobbin in a Bernia artista165 I followed all directions that came with machine.


Answers :

Hello :

Check for manual here please : http://safemanuals.com/zearchres_3366.php

good luck
Looks like your question went into the Vacuum cleaner category.
\015\012
\015\012I would have thought the bobbin in the Bernina should be no different to any other standard sewing machine.
\015\012
\015\012See picture of bobbin in place at the bottom of page in this document
\015\012
\015\012http://www.janeansbernina.com/_fileCabinet/sewingmachineTLC.pdf
\015\012
\015\012Once you thread the small spindle and place it inside the bobbin, you hold the two together between your index & middle fingers and thumb. Make sure the end of the thread comes out of the bobbin case. Use the thumb to lift the bobbin catch lever. Next insert the bobbin inside the cavity making sure the small tounge jutting out of the bobbin goes into the recess in the cavity.
\015\012
\015\012Close the machine and get the thread to come out by moving the needle.
\015\012
\015\012Please post a comment to make sure I have understood your problem.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I get bobbin in a Bernia artista165 I followed all directions that came with machine.


Hello : Check for manual here please : http://safemanuals.com/zearchres_3366.phpgood luck ... Vacuums

I have a Kenmore 385.19110 model machine, and the straight and zig zag stitches work just fine, but when I follow the directions in the manual to do a satin stitch (which is use the lowest stitch length) it creates a line that isn't perfect, or uniform, and after an inch or two stops catching the bobbin underneath. Have already tried reinserting the bobbin, rethreading the machine, refilling the bobbin, changing the bobbin, cleaning the needle, changing the tension. Wondering if I just got a mac


... Vacuums

I have a Singer Model #4562 sewing machine. I am having trouble adjusting the tension. Everytime I try and turn the knob to adjust the bobbin just gets looser. Right now it just snags and gets caught underneath the material and bunches up into a big ball. There is a lot of thread inside the bobbin case that came out of the bobbin and has to be cut out to free the material. How do I fix this mess. I am a novice at this. I have not sewn in several years and would like to sew a few quilts


... Vacuums

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me


Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums

Hi. I can get my FunLock 007D serger threaded fine (as it's color coded) until I get down to the area that includes threading the needle. Can you give me some instructions that will guide me through this? I have the manual that came with the machine, but the illustration isn't clear or specific enough for me to follow. I'd sure appreciate some assistance on this. My e-mail address is: [email protected] Thanks you. Vicki Flagg


More specifically, what are having problems with when it comes to threading the needle? ... Vacuums

My Janome Harmony 8100 will occasionally stop and give me a System Error #1 - I cannot find anything about this error. It is a computerized machine with 70 stiches and attachable embroidery hoop. I first started getting this error with the hoop and now get it when I am just sewing. As soon as the needle goes down to the bobbin, I get the error. The machine freezes and the only way to get rid of the error is to turn the machine off. Sometimes I can get the machine going again, but now it wil


... Vacuums

I got my Mom's Kenmore sewing machine and I an trying to figure out how to get the scalloping and arrow head stitches to work. I have followed the manual and I can get all the other stiches but those two. It is a Model 1451 zig zag machine. I realize it is old, but the machine is just like new. HELP. Thank You.


... Vacuums

I have Necchi Lydia 544, inheretade, and don't know which way the needle is fixed! what side does the flat part of the needle face? Also, what are the two bobbin holders on behind the main body of the machine, and how do they work? And, how the hairy heck! do I thread it? finally, for now! How do I get the bobbin holder to ...a...hold the bobbin, and b...make it stay in the machine, ..well, it obviously attaches in one way only, and I cannot find that way!? Thanks, Yvonne.


Hi,Here are some websites with useful information on your machine:http://www.free-guitar-tablature.com/Lydia.html This one shows how to take the bobbin case out with pictures.http://www.youtube.com/watch?v=FbEMwLNzsG4 ... Vacuums

I have a Continental Electric portable sewing machine and I can't get the bobbin to thread into the machine to start sewing. How do I place the bobbin and where does the thread need to go for the need to catch it?


... Continental Vacuums

I have recently got my sewing machine out after several years of it lying unused after moving house. I cannot find the manual. Where can I get a copy of this manual.The second request is that i need to put different cotton onto the bobbin and can't work out how to remove it from the machine. there is a clear "plate" over the bobbin , but I can't seem to remove that.


You posted in the wrong category and there is no mention of make/ model in your question so sadly it is impossible to help you.If it is any consolation this is in part due to the very poor way that the fixya question posting process works. ... Vacuums

Our beautiful Bernina 730 sewing machine has been stored in the garage in its original case, and that wrapped in plastic, for a few years now. Temperatures have been both hot and cold in the garage, but the environment was dust-free. We have brought the Bernina in, set it up, oiled it as specified in the manual, with the original sewing machine oil. We have correctly threaded the machine and the bobbin thread is up. When we press on the pedal to sew, the machine gets electricity and buzzes


Hello and thank you for using Fixya ....From what you describe there can be only 2 causes...Either the machine is still stuck ..and the motor buzzes cause it can not spin it ..and in this case it needs to be oiled more..and be spun by hand unt ... Vacuums

Jun 24, 2010 - Jun 24, 2010 - Needle not bent/ new needle not answer. I finally conclude that the entire bobbin case is ROTATING in its seat, which jams the needle. The "projection" is against the "spring" when I install it, but I can rotate the bobbin case PAST the spring without trying very hard. Bobbin case MIGHT get held in place better if it were closer to me (front of machine). I feel it is still not out from under needle plate as shown in diagram, but can't keep it closer to f


Hi,Your problem dated 24th June 2010 was re-posted today. If it has been already resolved, kindly ignore this message.Thanks for using FixYa ... Vacuums

I have a dyson alergy machine, I have emptied it, but I would like to clean the filter. I can't locate where the filter is or how to get to it to clean it. The manuel for this is not with the machine. This machine came with the house we live in. Could you help me please? Laurie


Greetings Irlawren3, \015\012\015\012It all depends on the model you currently have. The filters on some are above the motor and some are on the side housing. Its pretty clear looking at the unit where the filters are located. I would su ... Vacuums

No problem I just need a manual. I bought the bissell from lowes and it was a floor model. They did not have the manual with the directions on how to use the machine. They told me I could go online and get the directions or have a manual sent to me. I would rather have a manual sent Thanks. My address is B. Carothers 5969 walker rd. walker Wv. 26180


Http://www.bissell.com/DownloadAsset.aspx?id=647 ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Would it be possible to get a Viking 714 sewing machine manual? I just inherited the machine and would like to use it, but it came without the manual. Thank you! Your help in this is much appreciated! A.S.


... Vacuums

The needle is to the left and back of center, frequently hitting the plate and breaking. The hoop came unsnapped while embroidering, and caused needle to bend, stopping the machine. That was no doubt when the shaft that holds the needle became askew. How do I reposition it? I don't see an appropriate category listed below. Small appliances is as close as it gets, which does not give me a high level of confidence of having an expert for my Babylock Espree EM2 embroidery machine on your staff


I work on my wife's sewing machine all the time and saw your post when I was about to leave but I have a couple of appointments to go to.Although you say yours is for embroidering,it should not matter.When I get back I will take a look around and see ... Vacuums

Cant figure out how to thread elna 1000 lotus sewing machine. also the bobbin keeps getting tangled. if you could send me a diagram on how to thread and bobbin i would appreciate it


... Vacuums

My Kenmore sewing machine timing has gotten off. I am sewing a big upholstery project and it starting bunching thread from the bobbin. The thread is so heavy that I had to put some pressure just to get it undone. This happen a few times and then I found it wasn't sewing at all. When I evaluated without the materials in place I could see the needle would catch on the white plastic piece under the bobbin and the thread would not catch on the metal arm. It appears to be off by 1/4 - 3/8 inch.


HelloDisassemble your bobbin case which is realy quite easy, clean\015\012thoroughly with a brush and air, paying particular attention to any\015\012rust that may have formed, and any thread that may have weazeled it's\015\012way into sma ... Kenmore Vacuums

I have had pfaff 1037 tipmatic machine since 1999. Have been servicing it regularly. Unfortunately, the wheel, which you loosen when filling the bobbin with thread,has broken. I mean the screw which holds the spring has broken. Where can I get a spare part. I asked for the whole machine photograph so that I can tell you exactly which part I mean as unfortunately I do not have a manual for this model.


... Vacuums

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have an Elna 2600. I'm trying to thread the bobbin, but it won't turn. I hear the machine on but the bobbin stays put. What do I do? I've rechecked the directions several times.


... Vacuums

Vapor Clean TR 5 Under "maintenance" they told me to unscrew to empty refill tank. After doing that, no water came out and the piece that the scew went into is now in the tank. It is too large to get out and even if you put the screw back inti that piece ir still goes into the machine. Can I still use the machine? brand new only uded it once


I is really needed to check this with the manufacturer! See contact details below: ... Vacuums

When I was putting my new rug shampooer together and the directions said to press the trigger and the clean surge button until I heard a snap, I did just that many times and never did hear a snap so I thought it had likely happened and I didn't hear it so I proceeded to fill the solution tank and get busy but no solution came out so I used the clean surge button instead and got the job done (I think). Can I continue to use it that way or is there a way I can get it to snap and use it the way it


My husband figured it out and it now works great! Thank you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a Necchi Sewing Machine Model #523 (40 years old). It operates well except for the following problem: the bobbin-winder spindle does not wind, and thus nable to fill the bobbin flange with thread. Thank you.


... Vacuums

I have an antique White sewing machine. The plaque reads Dressmaster made in U.S.A. It is green cast iron. The numbers on it are 605-9761 and E6354. I cannot figure out how to get the bobbin thread to pull up. Where can I find a manual?


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0683 seconds