Having problems with your Vacuums ?

I have a canister vacuum. I replaced the bag and now can otn get a good suction. Could it be the rubber seal near the bag?


Answers :

The case that encloses the bag may not have been closed properly, or a part of the bag got caught in the seal of the case. Take the bag out and reinstall. Hope this helps!
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a canister vacuum. I replaced the bag and now can otn get a good suction. Could it be the rubber seal near the bag?


The case that encloses the bag may not have been closed properly, or a part of the bag got caught in the seal of the case. Take the bag out and reinstall. Hope this helps! ... Vacuums

Hoover HWD015 wet and dry vacuum cleanerThe safety seal float keeps on getting "sucked up", thus stopping the suction of the cleaner. The dust bag is in very good condition and the filter has been thoroughly cleaned. Any solutions for me please?


... Vacuums

When removing the canister bag, the plate and spring that it slides into popped out. When I put them back in, the bag full indicator is completely red. It is a new bag and filters. I think I am not getting the plate and spring back in the canister correctly. Any instructions or pictures showing proper insertion and configuration of these? I looked in the manual and the part is only shown while bag being inserted.


... Miele S514 Solaris Bagged Canister Vacuum

I HAVE A DC33 BRAND NEW DYSON I EMPTIED TO CANISTER AND NOW CAN NOT GET IT BACK ON FOR A GOOD FIT TO GET SUCTION


... Dyson DC33 Multi-Floor Upright Bagless Vacuum Cleaner

Hi, I have a Dirt Devil Model # M08100REDC. I desperately need to change the bag, but I don't see an obvious way to do it. I'm afraid to try pulling on the cloth tab thingy that's just below the handle, between the rubber ring that holds the bag on the vac, because it seems like stuff will fly everywhere from the force required to remove it, and I might not be able to get it back on there. Should I just pull on that cloth tab until the bag comes off? Thanks, Roberta


You can pull on the tab to remove the bag, but probably a better way is to gently pull on the rubber ring that attaches the bag to the back of the vacuum body. If you don't yank and ****, it should come off without spilling the dirt. There may also b ... Dirt Devil Classic M08100 Bagged Handheld Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

Seals leaking Where the canister meets the machine, the seals are leaking, blowing whatever manages to get sucked up right back into the air. I can't see anywhere to buy new seals. What to do?


Hi.\015\012\015\012If you live in the UK I can help you.\015\012\015\012http://dysonmanuals.inc.io/\015\012\015\012Chris. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Have a Eureka Power Plus 12.0 Amps Model 4702 Type A 120 volts and 60 HZ that there is something wrong that it isn't picking up right and you can actually feel the air coming out of it near where the bagless canister attaches. My thoughts are that a seal is missing around where the hole lines up when the cannister is locked in. This Vac was my Mom's and she passed away and I think a part went missing maybe when it was taken apart to clean the filter and empty the canister. Need to figure out if


... Vacuums

Low suction Have a Powr-Flite PF 18, suction is good at motor, but low at where hose comes out of top of vacuum. Could new lid seals help the problem? Where can I get new seals for this model. Also my zip is 98801 and my shop is not listed, could you add it please? Sew Creative 1139 N. Princeton Wenatchee, Wa 98801 509-663-5516 Thanks, Lauren-Sew Creative


Replacing the motor cover solved the problem, it must have been warped and was letting suction out thru it. ... Vacuums

FAN PROBLEM??? good morning! my vacuum smells like burnt rubber (fan perhaps) but I can't find how to get into main part of the vacuum. it's just very rounded with no latches or screws to get inside where the motor, belts and fans would be located. can you help me? thank you


There isn't any belts, and the fan wouldn't be rubber, so not sure what you are smelling. Maybe this picture will help you.\015\012\015\012 ... Bissell 6700 Butler Revolution Bagged Canister Vacuum

Inside the my wd09450 there is a part missing which holds the dust bag on to the end of hte hose. the rubberized port of the bag should fint over it. where can I get one?


... Vacuums

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

Bissell powerforce My lower pickup tube became clogged so I removed it and cleaned it out and reinstalled it.Now everything runs good but the vaccum want pick up any dirt .I replaced the bag andf when I turn it on it just exhaust air but does not have any suction,I tired tp pull the bag door of while it was running whick I could not do so it has plenty of suction inside just not getting any outside can you help?


... Bissell Vacuums

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet


Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Vorwerk ET 340 - been great but now noticing strong burning smell after vacuuming some hair from the bathroom. Bag is nearly empty. Gave it a rest then unscrewed the cover housing the motor and all looks clean (dust is sucked up the pipe and doesn't appear to get near the motor). When I restarted it, burning smell still there. Are there any filters that might need changing? What could be causing the smell? Could the hair have gotten caught somewhere? Thanks.


Jessica,\015\012\015\012Try changing the dirt bag.\015\012Check if the motor gets hot after operation. You can come to check it by touching outside the motor housing. If it is hot or just warm.\015\012Is the smell of burning hair or something e ... Vacuums

I have an Electrolux EL 6988 type E Oxygan Bagged Canister vacuum brush roller in not working. I took off the stuff that was stopping to rooler from working and now I can't get the roller to move.


... Electrolux EL7024A Oxygen3 Bagged Canister Vacuum

My vacuum is making a whistling sound and when I turn it off it momentarily gets louder and makes a honking sound. The vacuum is a Kenmore canister vac model # 116.27814. It has a new bag and filters.


... Kenmore 27814 Bagged Canister Vacuum

How to wind cord onto spring loaded retractable cord reel for a Kenmore canister vacuum. There is a metal 'U' shaped, spring loaded, piece that fits over the outer aspect of the wheel. If cord needs to get wound on under this metal band I can't figure it out and the band is like factory sealed onto the wheel. Also. I don't know which direction to feed the cord onto the wheel


What is the exact model # please?Thanks!! ... Kenmore Vacuums

A friend gave me her Oreck 1400 canister vac. It's like new, but has no "filter bag carrier." Where can I get one?


Sadly, your best and probably only bet for this is either an Oreck dealer or by calling the 1-800 line for Oreck customer service. ... Oreck DutchTech DTX1400BD with Powerhead Bagged Canister Vacuum

Brush works intermittedly - I've looked at the common solutions listed but none seem to work...shaking it & reseating the canister will get it working again sometimes but obviously that doesn't seem to be a very good solution. Can you help?


I just had the same problem. I would turn on the vac, and it worked fine. When I turned on the brush it would work for a few seconds then shut off. Through troubleshooting I found out it had nothing to do with a bad power connection. By chance I took ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

How do I get the silver/grey panel off? - Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum


Pry gently upward on the front side of the panel. The side closest to the bag area. When you press it upward and also slightly towards the back of the vacuum the plate will pop off. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

We've changed the bag and we are still not getting good pick up. It seems to leave small paritcles and bits of fuzz.


I have a wind tunnel and it is so "STOPPED" up that it won't pick up anything ,. How do i un stop it? ... Hoover Company Wind Tunnel U53019 Upright Vacuum

Where can I get replacement bags for the Readivac Model 36721 canister vacuum?


We have the bags ReadiVac 36010 ReadiVac Tidy Turbo Vac bags ... Readivac 36721 Canister Vacuum

How to open 116.23512301 vacuum canister AC section to wire in replacement 4370608 cable assy. This assembly contains the receptacle that powers the hose. I found the two screws below the bag cover, but can't figure out how to release the end near the retractor lever.


... Kenmore Vacuums

Clean water leaks out of the side of the cleaner when snapped into its place. Maybe not getting a good seal or somthing?


You have a bad solenoid. It is supposed to stay closed unless the trigger is pulled but when they go bad they are open all the time. Take it to a vac shop ... Hoover F7431-900 SteamVac Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0669 seconds