Having problems with your Vacuums ?


\015 \015\012MY KIRBY G4 FAN WAS BROKEN, I JUST PURCHASE A NEW G4 FAN KIT. This kit includes a new fan, new pulley, new spacer, new washer, and a new gasket. THE ORIGINAL ONE WAS A ONE PIECE METAL FAN.\015\012I NEED HELP TO ASSEMBLE THE G4 FAN KIT IN THE RIGHT ORDER.\015\012 \015\012THANKS IN ADVANCE FOR YOUR ASSISTANCE.\015\012SINCERELY,\015\012 \015\[email protected]\015\012\015

Answers :

First put the gasket on the spacer, thin end to to out, push it down all the way on the motor shaft, then put the nylon washer on, then the fan, metal washer and then the pulley, just snug it, (don't tighten too much just beyond hand tightening). Put the casing, top and handle back on.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :


First put the gasket on the spacer, thin end to to out, push it down all the way on the motor shaft, then put the nylon washer on, then the fan, metal washer and then the pulley, just snug it, (don't tighten too much just beyond hand tightening). Pu ... Vacuums

I have taken delivery of a new Lloytron Halogen Oven E4701 WH.from a supplier in the UK (I live in Spain). On unpacking it I found that Part of the temperature control knob assembly had fallen down inside of the heater body. I dismantled the heater body to retrieve the part but I cannot now work out the order of re-assembling the fan parts so that the fan does not catch on other parts of the assembly. I cannot find a parts drawing on-line. Can you help ?

... Vacuums

Kirby vacuum cleaner G4 fitting new fan order of assy of washer and seal ...which way does the soft seal face and assy order of soft washer, I assume the steel washer is next to the retaining nut/pulley. Ozzie

... Vacuums

Replacing fan assembly on Kirby G2000 - Vacuums

This video should get you half way there:\015\012Kirby belt replacement\015\012\015\012Hope it helps ... Vacuums

Fan and bearing replacement on a Kirby G6

If you run your vac to long after the fan is broke it will cause excessive vibration and the bearings can go out. in almost all cases i replace the fan only. most of the time if you have a bad bearing the vac will make a grinding noise. you can also ... Kirby G6 Bagged Upright Vacuum

Kirby Heritage 2 fan replacement

Take the bag asm. and handle off. Then remove the plastic strip covering the switch, remove the screw there, remove the 3 screws on the housing, turn it over and loosen the screw near the back, the housing should come off. Then remove the screws on ... Kirby Heritage II Vacuum

I have a Kirby Generation 3. The handle spring assembly is broke, so I took it apart to get a part number. Can you tell me if there is a cross reference or something on these parts. I am unable to find a part with the same number that is located on the part I took off. The number on this spring assembly shows Kirby HA-670289B K-1. Any help finding this part is appreciated.

... Kirby Vacuums

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.

... Vacuums

Kirby Vacuum Fan

The pullet is what holds it in place, if it has come loose, just tighten it. But if that doesn't help, then replace the fan. ... Kirby G6 Bagged Upright Vacuum

Replace Kirby legend II fan (impeller blade) - Kirby G4 Bagged Upright Vacuum

In order to replace the fan you will buy a 2 or three piece lexan fan kit containing the fan a spacer and shaft. You must remove the carpet head and then looking from the back of the machine you will find a series of philips screws on the oute ... Kirby G4 Bagged Upright Vacuum

How do I assemble kirby g3 carpet cleaner? - Kirby Generation 3 Bagged Upright Vacuum

Greetings,If you click the link below it will take you to a video demonstration that explains step by step what you need to do to convert your Kirby into a carpet shampooer. The vacuum in the video is the Kirby Sentria, but the procedure ... Kirby Generation 3 Bagged Upright Vacuum

I have a Simplicity (Danby) SDR458H Dehumidifier. The bearings in the fan motor have become loud and scratchy sounding (due to a plugged-up filter in the past). I would like to get a repair manual for it with part numbers so I can order a new fan motor.

... Simplicity Vacuums

Kirby G3 made loud noise when running. Sprayed silicon in fan thinking it might be a bearing. Found a coin and nail in fan and removed. Tha vacuum would not turn on. Replaced switch and brushes. Still nothing. Did the silicon spray do something?

No - the silicon is an insulating material and would have no effect on the electrics of the vacuum. Most likely you have a bad connection - dismantle the vacuum again and check the wiring and the motor with an ohmmeter. Be very attentive with the bru ... Kirby Generation 3 Bagged Upright Vacuum

How do I put the belt on the Kirby the correct way in order for the green light to come on? The green light indicates that the Kirby will pick up.

The G4 has a magnetic block on one end of the brush. It must be aligned on the LED end of the brush housing. ..with adjustment screws facing out. When setting the housing back in place use the pedal to lift the carpet nozzle up off the work surface ... Kirby G4 Bagged Upright Vacuum

How to install Kirby g4 fan - Kirby Generation 3 Bagged Upright Vacuum

It needs to be stripped completly down, if you are confident at doing this then here goes.\015\012It has been a while for me so take your time and some of the steps may have to be completed slightly differently.\015\012Isolate / unplug t ... Kirby Generation 3 Bagged Upright Vacuum

This fan is the Aloha Breeze 16inch Vintage Stand Fan made in March of 2010. Serial# 02299 model # 46052(46051) purchase order # 2082395186 UPC # 759590460526 it is the heavy chrome model. We have owned this only 3 months and it just quit working. No symtoms, no pre-warning, no smokeing, it just quit. HELP

You are still in the warrranty period of one year and it is most adviceable not to tamper it so as to lose the priviledge.\012So please get in touch immediatley with your dealer.\012Only If there is no help do you need to open the base an ... Vacuums

I need to replace the fan blades on a Kirby Heritage II, Model 2HD, vacuum cleaner. How do I remove the drive shaft that the fan is mounted on? Thanks, Robert Croft

... Vacuums

Broken fan need a repair man or service centre. If not a replacement fan for self repair. I live on the Gold Coast Ray is my name. Kirby Legend 1 model 2HE

Http://www.ultimatesanitarysupply.com/pdfs/VacuumMaintenance.pdf\015\012\015\012see the link ... Kirby Vacuums

How to change the fan in kirby heritage 2 - Kirby Heritage II Vacuum

This site has a great tutorial on how to do it. I did it myself and it worked out great. Get the parts online or at your ... Kirby Heritage II Vacuum

Parts diagram I have taken the assembly apart and I would like to see a diagram in order to know the part numbers that i need to order for repair.

You may like to try here see if yours is listed http://onlinevacuumparts.com/s-3-bissell-vacuum-parts.aspxriz. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Bad fan how to remove fan on kirby heritage 2 legend vacuum cleaner.

There might be latex sealant around the perimeter of the fan casing. This was the case with my G3. The latex sealant prevents dust from blowing out of the fan "chamber" while it's running and under positive pressure. And as reddevil16 said, the spind ... Kirby Ultimate G Bagged Upright Vacuum

Kirby Heritage II 2HD Vaccum Cleaner. I have removed the housing and reached the motor shaft for the vacuum fan. How do you remove the fan from the shaft.

Hi, you can visit this site to view how to remove the fan from the shaft...http://www.diyonline.com/servlet/GIB_BaseT/diylib_article.html?session.docid=1678Take care ... Vacuums

Kirby Seems like you know alot about the Kirby. I know how to use my Sentria (unlike these other idiots) but I keep screwing up the shampoo tray assembly. The brush snaps into the tray just fine but the tray doesn't really stick to the head. It detaches when pushing and pulling the unit. And who knows where that cover goes? It say 'push here to open'

Machine will not come on ... Kirby G6 Bagged Upright Vacuum

Trying to attatch the wires from the light kit to the fan but the blue and white wires from the fan have white caps on them covering the wire. Do these need to be removed in order to attach the wires with the wire nuts? If so, how are these white plastic caps removed?

They're called "wire nuts". Turn them counterclockwise to remove, lay the wires you need to join side by side with the ends of the bared sections even and screw the nut on. lp ... Vacuums

How do I change the fan in a Kirby G3 vacuum cleaner

See this MANUAL. Let me know if it helped ... Kirby Generation 3 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0418 seconds