Having problems with your Vacuums ?

My electric shower is getting very hot lately what is causeing this? it is a tryton t90 fed off the tank


Answers :

Hi,
\015\012
\015\012This more looks like a thermostat problem, as it looks that its is not functioning well.
\015\012
\015\012 Basically, if you turn a tap on, the amount of water flowing through your shower reduces - less water to heat means the water coming from shower gets hotter.
\015\012Also check if you don't have taps/washing machine etc running, if shower is mains fed water pressure changes from mains can have same effect.
\015\012Please try the steps below befora calling a repairmen as it has worked in most cases:
\015\012When you open the unit it might be handy to take photo with digital camera to help put it back together.
Open up the uniit and where the water enters the unit on the Top LHS there may be a filter (gauze type), this may be blocked, clogged with dirt.
Unscrew the screws and take out this filter if prsent and whatever other bits of plastic pipe etc that come out. Blow through them or wash them to remove dirt etc.
Behind the temp selector there is usually a metal type slider thingy, try moving this a little bit.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My electric shower is getting very hot lately what is causeing this? it is a tryton t90 fed off the tank


Hi,\015\012\015\012This more looks like a thermostat problem, as it looks that its is not functioning well.\015\012\015\012 Basically, if you turn a tap on, the amount of water flowing through your shower reduces - less water ... Vacuums

The water tank has imploded,what caused this to


... Rainbow Vacuums

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

November 2008 I bought a Simac Stirella 9000D steam generator iron. Recently its been leaking water out the bottom of the regenerator. It makes a noise when it is trying to get the steam to the iron and it works then but afterwards when the noise stops it stops steaming and I find a puddle of water underneath the regenerator. Also a little steam comes out of the water tank at the top. I understand this is happening because of scale in the base unit. Can I get something to get rid of the scale? -


... Vacuums

I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 - On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 - not


Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I


Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum

Can I get a new clean water tank for my Hoover? After filling tank, as soon as I lock it in water poors out even before I can start cleaning carpet.


Take the clean water tank off, and look at the underside very carefully. This tank is made of a very thin plastic, and chances are, your tank is cracked or broken. Sometimes the valves fail as well. There is a new tank available, a single ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have an older Wega 2 group espresso machine. Looks like a date of 1992 on the group head, but not sure. This has no model name that I can find. Anyway, when I turn it on I get all lights flashing after it heats up 5 minutes or so. I do get nice steam from the wands. I drained teh tank and found a little scale, but not much. I took apart the group heads and cleaned them thinking it may be a clog there, but that doesn't seem to have worked. Also fwiw the water level float is not visible and whe


For a new fridge, need more time to maintain the required temperature of the fridge abut mainly the goods in it? So everything seems normal. The time will be reduced day by day since the goods will stay for longer time in and door opening will bec ... Vacuums

I have to go into the garage to turn on the motor on the tank and to shut it off. When I plug the hoses into the outlets in the house, it doesn't turn on the tank motor. I don't know what part to get and nobody in Raleigh, NC shops can help me.


Is this Electrolux that's now known as Aerus? If so, take it in to the Aerus Electrolux store for a tech to look at. You can find the nearest Aerus Electrolux store by following the instructions on the site at bottom of page.\015\012\01 ... Electrolux Central Vacuum

I have an older model F6056-900 Hoover steamvac Spin Scrub Cleaner. My first problem was that I loaned it out to a friend. Anyway she ran over the hose (used for attachments) with her car. I tried using the cleaner for carpet cleaning this morning but when I tried to put the solution tank into place...its loose...won't snap back in like it used to. When I can get it somewhat in place the solution just complete drains out through the bottom fo the tank. The leak is where the small hole on the bot


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Cannot get the tank to lock down on the turbo unit so it will **** the water up into the tank. Will not seat in place. need instruction manual to see what we are doing wrong.


There is a lip on the front of the tank, hook it under the front of the machine then it will lay down flat ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissel proheat 7901 carpet cleaner and it is not sucking the water up. Normally when I clean the water gets sucked back up and I have to empty the dirty tank. Now no water is in the tank when I am done cleaning. Please help I cannot afford to take it to the shop.


I'm not sure if this will help but I had the same problem and was about ready to pull my hair out. I ended up taking the fill tank off and if you look inside where the red overflow flap is you will find a small screened opening. I found that mine w ... Vacuums

Bissell Proheat - I need the manual - how do I get the water container back into the machine? I took out the tank and filled it up with water but I cannot get it back in. I need a manual or a picture of how to do it. thank you, ruth


Http://www.bissell.com/images/UserGuides/7950_1204.indd.pdf ... Vacuums

Roller not turning, belt not working no water . The belt on my Bissell Proheat is not getting water (although there is plenty in the holding tank). It seems the belt is not turning and there fore the water is prevented from leaving the holding tank.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Can't get water tank out to get started - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


Lay handle down to back all the way and flip the round shaped handle on the rear of the water container to the front half way as if you were going to pick a bucket up by the buckets handle, and pick it up just like a bucket and when you return it mak ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum

The telescoping wand on my kenmore magic blue cannister vacuum stopped working shortly after I bought it a few years ago. After 10 minutes of pushing sometimes I get it to work. It gets longer easier than shorter. What could be causing this problem? Please help!


... Kenmore Magic Blue 24195 Bagged Canister Vacuum

Vapor Clean TR 5 Under "maintenance" they told me to unscrew to empty refill tank. After doing that, no water came out and the piece that the scew went into is now in the tank. It is too large to get out and even if you put the screw back inti that piece ir still goes into the machine. Can I still use the machine? brand new only uded it once


I is really needed to check this with the manufacturer! See contact details below: ... Vacuums

GE reverse osmosis model GXRV10ABL01, I have replaced both filters and the membrane and the output of filtered water from tank is about one cup. in about 30 min or 8 hrs I can get another cup. I suspect the tank, help.


... Vacuums

We bought a Philips Intellicare 8030 ironinng system in 2005. Two days ago water from the plastic water container does not go inside bigger water tank where we think the water gets heated up. When the heating tank is empty there is no steam that comes out of the iron. Also, there is water dripping off profusely from under the iron where the steam normally comes out. Can you please advise how we should remedy this problem Please advise which service centre in Sydney, Australia would we be able to


... Philips Vacuums

Bought an PlayStation 2 at our youngest dauthers 9 year birthday together with an dance mat. Caused by an accident we had to buy a new remote contol for some years ago and we chosed your URC-3445. We can't get it to work. How do we get to AV-chanel throughtout your device? There must be a solution at our problem. Please help ....! Her anniversery is unfortunally today!!! Our TV is an rater old Tandberg modell: TVF2915NT Please...


Go to menu settings, find channel edit or add/delete, turn channel to input or a/v channel, select add channel and then your good. You should now be able to use the ps2. You can also hook them up through vcr and use the vcr input/av channel. and then ... Vacuums

When I was putting my new rug shampooer together and the directions said to press the trigger and the clean surge button until I heard a snap, I did just that many times and never did hear a snap so I thought it had likely happened and I didn't hear it so I proceeded to fill the solution tank and get busy but no solution came out so I used the clean surge button instead and got the job done (I think). Can I continue to use it that way or is there a way I can get it to snap and use it the way it


My husband figured it out and it now works great! Thank you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Hoover SteamVac is spitting out dirty soultion from the recovery tank, it seems. I have removed the clean solution tank and turned it on to **** up what was soaked into my carpet and it just kept spitting out slowly. When I first turn it on, it spits out a tremendous amount. What could be causing it to spit out solution?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I just used my Bissell Proheat, when I heard the vacuum sound get lower and lower then suddenly something "gave" and it got very loud and started emitting a burnt rubber smell. It still worked to put liquid into the carpet; seemed to have trouble getting it out. I checked the tank, filters, belt, and roller and all seemed OK - but when I started up again and looked down I saw sparks in the motor/belt area and shut it down immediately. Any thoughts?


The bearing that is located at the top of the vacuum motor has failed . Because of that the shaft of the motor's rotor is out of position and the pulley attached to it has started rubbing on the other pulleys, giving you that smell. the spark appear ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My Triton T80 SI shower is leaking from where the outlet pipe assy joins to the heater can assembly. when I checked where the two join together I see that there is a rubber O ring fitting into a recess in the heater can assy. The screws which hold the two parts together does not force a compression between the two parts causing it to leak. Is there another modified unit or am I stuck with what Ive got and should I replace the O ring or the shower.


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0534 seconds