Having problems with your Vacuums ?

I have a Bissell proheat model 9200. It dispenses soap but not water. The little pump is running and the heater is not plugged. Can I get a diagram of the hose hook up to see if they are all going where they should?


Answers :

Hi,
My Bissell also STOPPED SPRAYING WATER.

I've owned a Bissell\015\0129200 for a few months. I've used it twice, the last time most likely\015\012being around August. I attempted to use it this past weekend and it\015\012wouldn't spray. I searched all the help sites I could find and thought\015\012the solution was a clog in the heater, which many said was located in\015\012the arm. After I took the arm apart, to my surprise, THE HEATER IS NOT\015\012LOCATED IN THE ARM OF THE 9200 MODEL.

It's still under warranty, however am not located near a service center so I took it upon myself to try to fix it.

I'm\015\012just a single female who ends up trying to fix a lot of stuff herself\015\012so, I don't speak "technical instructions". But, here's what I did in\015\012the event that it may help someone else.

I unscrewed all the\015\012screws that I could on the base. I removed the cover over the motor.\015\012Doing so revealed the hoses attached to the soap dispenser. Located\015\012closer to the rollers were more hoses. On the same side as the foot\015\012lever, above the wheel is the where the HEATER is located.

Being\015\012that I was looking for a clog, I unclamped one hose at a time; inserted\015\012a safty pin into what the hose was attached to and wiggled it;\015\012re-clamped hose afterwards.

The only slight confusion may be\015\012with the screws. There are only two sizes. I used finger nail polish to\015\012mark where the small ones went.

I reassembled it, turned it on, and it actually started spraying again!!!!!!!!

So that this "blockage" won't occur again, I will take advice I've read about cleaning Bissell's hoses out after using it.
See,\015\012taking the thing apart was really nerve racking! Especially not knowing\015\012if it would even work after I put it back together.

GOOD LUCK WITH FIXING YOUR CLOG!....you'll probably need to sooner or later.\015\012\015\012\015\012\011\011

Take care
Click on the link below to view a parts diagram for the Bissell proheat model 9200
\015\012
\015\012http://www.nelsonappliance.com/bissell+proheat2x+parts.asp
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bissell proheat model 9200. It dispenses soap but not water. The little pump is running and the heater is not plugged. Can I get a diagram of the hose hook up to see if they are all going where they should?


Hi, My Bissell also STOPPED SPRAYING WATER.I've owned a Bissell\015\0129200 for a few months. I've used it twice, the last time most likely\015\012being around August. I attempted to use it this past weekend and it\015\012wouldn't s ... Vacuums

The pump motor in my Bissel Proheat 2x Plus seems to have failed. It was seized so I sprayed WD-40 in it and let it sit for 3 days. Now I can turn it by hand, but when plugged into the unit it still doesn't spin. Here's a picture: http://bbay.dreamhost.com/bissel_proheat_2x_plus/P1070021.JPG I wanted to take the motor out and hook it into another power source to see if I can get it going but it has 3 wires. I'm used to only 2 (+ and -). How can I hook the motor up to another power source,


... Bissell Vacuums

Hello yes was i was wondering if you could possibley instruct me as to how the inner tubing hoses go back on the 8910 series it appears i am having no luck as to what tube hooks to what port ect? i figured somewhere surley there had to be a service diagram but guess what no luck?


Maybe this picture will help:\015\012 ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have to go into the garage to turn on the motor on the tank and to shut it off. When I plug the hoses into the outlets in the house, it doesn't turn on the tank motor. I don't know what part to get and nobody in Raleigh, NC shops can help me.


Is this Electrolux that's now known as Aerus? If so, take it in to the Aerus Electrolux store for a tech to look at. You can find the nearest Aerus Electrolux store by following the instructions on the site at bottom of page.\015\012\01 ... Electrolux Central Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hi I am wondering if someone could send me some (Schematics for a Bissell 9300-1) I took it all apart to clean out all the ( Hard watter out of the hoses) and now I cant remember where all the hoses go,I need to see where all the hoses go so I can hook up if someone could help me out! Thanks!!


Hi, you should be able to download the manual/manuals you need on the following web page. Just paste the following onto your search bar. I've used this site to find manuals before, it can be trusted. Good luck!\015\012http://www.manualsonline. ... Bissell Vacuums

Getting part My repair shop cannot get the part for my filter queen. It's the plug in the body of the machine that the short plug goes in from the hose. It's been bent. Can I get a replacement part?


Have you called your filter queen dealer? i used to be a rep. and we would fix problems at the office that i worked out of. hope this helps. ... Filter Queen Majestic Canister Vacuum

The solution has stopped going out the hose. The hose seems to be deep inside the machine. How do I get to it to unclog it?


The hose unhooks by the motor. But it could be the valve in the hose head. Maybe this picture will help:\015\012\015\012 ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Wondering if the head is plugged up because it makes a sound like air is escaping somewhere. I've replaced the original cloth bag with a comparable "O" paper bag from Sears. I tried to see if there was a clog in the hose by placing a broom handle in the hose to see if something would loosen. I also cleaned the filter and the air filter. If the head is plugged, how can I fix it? We can't get the vacuum apart. Thanks.


I had this problem, but suction improved when the attachments were properly secured in their holders. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I forgot how all the interior hoses hook up to the bissell proheat 3930 shampooer. is there any skamatics diagrams to show yo how each hose hooks up.


Click this link directly \015\012http://www.bissell.com.au/images/IncludeContent/Service_Center_ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

Shampoo-er This seems to be a common problem, the shampooer is putting out alot of water and hardly any suds. I read through the posts about the little filter that sometimes gets out of place and I think I found it in the box - is it about 1" diameter hard plastic ring around very fine mesh? If so where exactly does it go? Some posts say in the hose, and others say in the opening of the tank. Or does it go in the place where the hose attaches to the tray? I also found a round sponge in the box o


It goes on the small hole on the tank where the hose attaches to it. The sponge goes in the hole directly under the on/off valve. Here is a link to my online shampooer instructions.\015\012 \015\012 ... Kirby Ultimate G Bagged Upright Vacuum

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is


... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Rented triumph 430 and cant figure out how to work the accessories. I have the vac hose and a smaller hose attached ro dispense solution. There appears to be no way to plug in the smaller clear hose. Was I supposed to get another length of hose to connect from fitting on accessory to machine?


Yes don. call the store where u rented and tell them. ... Vacuums

No Suction I get great suction in the hose, but when I plug the hose back into the unit, there is no suction and the air flow indicator line goes completely red. I've changed the bag and filters. I took the small panel off the back and made sure there is no clog, and took the hose off to make sure there was no clog there. Still no suction. Please help.


I about to say that's always a clog of some sort that causes that ... Miele S7210 Bagged Upright Vacuum

Hoses I have a bissell took it apart cant remember how the hoses go back is there a diagram I can look at I have the scehmatic to the whole machine but not the hose placement help


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Cant seem to get the green light going on vacuum head,hook seems to be wrong way when its should be hooking the band off its doing the opposite


1)First, you turn the square belt lifter on the front of the power nozzle until the red arrows line up (belt off)2)Remove the power head from the front of the machine. Now turn the belt lifter the other way and line the green arrows up ag ... Kirby Ultimate G Bagged Upright Vacuum

Cannot get hose to go back down.


Hi there SmartAlec from NelsonVacuums.com.au here. I think you will find that the hose will lock in easier if you remove the clear bin of the dyson. If it is not this then ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

What hose gets hooked up for upholstery cleaner. The one that usually goes in front? I cant get my vacumn to turn on.


Hi!You need to take the power nozzle off and attach the thing that looks like a little plastic "cup" with two hooks and a screen on it. This is the intake guard. Attach it to the front. Now remove the cloth bag and put the hose on the hole wher ... Kirby Ultimate G Bagged Upright Vacuum

I have a bissell bagless easy vac. When I vacuum the debris keeps getting stuck in the hose (also going into the filter area and the apparatus above the cannister with none of it going into the cannister. I have made sure the cannister is properly placed and the lock is pushed in all the way.


... Bissell 3102-0 EasyVac Upright Vacuum

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

On my DC17, the wand is not working right. The upright part works fine, but when I go to use the wand, the hose sucks in on itself. I get suction for a few seconds, then the hose collapses in on itself and no more suction.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

CANISTER IS GETTING POWER BUT NO SUCTION FROM HOSE AND DOESNT SEEM LIKE THERE IS POWER GOING TO HOSE..I HAVE CLEANED OUT THE FILTER AND CHECKED ALL BREAKERS...


Hello,Carnister vacuum cleaners are all built with the same \015\012principle in mind. A motor \015\012generates power which powers a vacuum which, in turn, creates suction to\015\012 lift debris. The most common areas of suction loss are ... Hoover S5615 Hush Central System Vacuum

Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?


Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0824 seconds