Having problems with your Vacuums ?

My eureka surfacemax 300 is not sucking up anything and i have cleaned out the hose plus i turns off by itself sometimes

Answers :

I've found that some times if you let the cup get too full, stuff will get jammed up above it. Turn off the vacuum and unplug it, and remove the cup. Reach up inside the vacuum above the cup and there is a small, plastic cylinder you can twist to remove (twist and pull down). clean this plastic piece off, and reach up inside where it was located. Clean out that crevice as well. Vacuum should be as good as new!

(It shuts off because it is over heating from not being able to pull anything through there.)
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My eureka surfacemax 300 is not sucking up anything and i have cleaned out the hose plus i turns off by itself sometimes

I've found that some times if you let the cup get too full, stuff will get jammed up above it. Turn off the vacuum and unplug it, and remove the cup. Reach up inside the vacuum above the cup and there is a small, plastic cylinder you can twist to r ... Vacuums

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being

Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I was given a model 6591, plugged it in and it worked but didnt "****" and didnt sound right. I turned it off and removed the hose from the back found a badly plugged hose. Removed the hair plug cleaned filters and when I tried to turn it on again. Now the motor will not turn on or even make a noise. I hear there is a fuse that can be blown? How can I find the fuse if there is one? Thank You Ron

The User Guide for the bissell Clearview Power Trak\012\012http://canada.bissell.com/images/UserGuides/3590C.pdf\012 ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

The brushes spin very, very slowly and stop altogether sometimes - like they just don't have any power behind them.I've cleaned the brushes and also turned it on without the brushes inside to see if the female plug that the brushes go into turns - it does, but not very fast. My husband said he thought he smelled something - like burning. Is there a way to take the underside cover off and clean something?

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Roomba Discovery Roomba is fully charged and cleaned with sensor wiped clean. When turned on it it sounds normal and commences to go, but it then acts like it is putting on the breaks, spins, tries to go and manages a short distance and breaks again, just not making any progress because it keeps breaking after a foot or so and turns and tries again. Sometimes is gets so stuck from moving forward at all, like it is stuck in one spot just trying to go while seemingly surrounded by barriers. Somet

I had the same back-up, turn, move forward a couple inches, backup-up, etc. problem. Try cleaning/cutting the hair, etc. out from around the brushes, as well as around the ends of the brushes. Also, try a Q-tip to clean out the four pair of sensors ... Roomba Robotic Floor Bagless Vacuum

My Hoover Mach 5 model number u5194-900 series ZF12.O will vacuum for about 15-10 min then it shuts its self off and will not turn back on., I have cleaned out all the hoses, filters and cleaned off brush. What can I do to fix this so that it will **** into the chamber. The hoses get clogged and it doesn't appear to be sucking into the "bag area"

... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!

... Miele Vacuums

My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there's a little thingy that should be spinning or turning..... When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI - I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn't wet. Any tips? The manual doesn't help.

You need to replace the pump belt. Here is the belt you need:Bissell ProHeat Belt ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.

Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a Kirby G4 Vacuum Cleaner - MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I've had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This

Hello,\015\012My educated guess is that it's either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair...\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

I have an Eureka Enviro Vac, I have replaced the filter, cleaned the hose and it still won't pick anything up. The brush is turning and there is suction in the hose. What else can I check?

... Eureka Vacuums

I have lost the manual and forget how to use the hose part of vacuum, also the handle turns and is not secure ( that is the handle in the upright position). It is a bagless Stick Shark Vac. I need to know how to attach the hose to the vac so I can clean furniture and corners.

... Euro-Pro V1828 Shark Stick Vac Bagless Vacuum

My vacuum is not working after cleaning a lot of dust. It starts w/o the hose but when i plug the hose it turns off on its own

Hi,\012 \012Take something and run it through the hose...your hose is clogged up...and yeah it has to be bigger then a wire... a wire will often push right through a clogg of dust...\012He ... Electrolux Epic 6500 Vacuum

Stops Immediately. We have a Beam Serenity model 2100 installed in the home and when the hose is inserted into the wall it turns on for a few seconds and then shuts off on it's own. Turning the handle's power switch off/on restarts the unit only to have it once again stop after a few more seconds. The canaster is clean. What could be causing this stopping issue? Thanks.

The Relay Control Board in the 2100 is bad. Replace and it should work just fine. ... Beam Industries 2900 Serenity Plus Central System Vacuum

My bissell pet hair eraser won't turn on. the clean filter indicator is red but the filters are clean and the hose is not plugged.

... Vacuums

Won't turn on. clean filter indicator is red but filters are clean and hose is not clogged.this is a bissell pet hair eraser.

Repair shop :( ... Vacuums

My dyson DC17 will not turn on unless the handle is pulled back.(into the vacuuming position) The attachment hose will not work at all (0 suction thru it). I've checked the hose and made sure there is no obstruction. Any ideas?

Not sure if I can help, but I'll try. The DC17 has two motors: the vacuum motor and a separate motor for the brush bar. It is normal that the brush motor works only when the handle is pulled back in the vacuuming position - that's the way it's made. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.

Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?

Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Bosch bsa2222uc doesn't turn on at all - non-responsive to any fiddling - cleaned the filter, won't turn on with hose unplugged either.

Check electric cord on the machine it may be broke leave power on shake cord if cut in and out replace cord ... Bosch BSA2222UC Compact Plus Bagged Canister Vacuum

I was vacuuming the vent in the bottom of the fridge. I must have picked something because the motor got wildly noisey. I cleaned out hoses, etc. There is no suction. I can see the blades of the motor and they are not turning around. Model U4269-930 Series B.72. Can I get at the motor to see if something is keeping the blades from turning? What would be your suggestion. Many thanks. Pat Sauerman

Hi Pat, my name is John I will do my best to assist you.\015\012\015\012You certainly can get at the motor, with simple hand tools. \015\012\015\012Referring to this ... Hoover Vacuums

Will not turn on....New bag, Cleaned Hoses, Pushed Reset

... Fuller Brush FB75T Upright Vacuum

No action Hi: My brush roll won't budge. After we cleaned out all the hoses and replaced a badly worn belt (burned?) when I turn it on the smell of burning rubber and smoke has continued. What hurts is that I don't think I've used the vacuum a total of 10 times ... and I had such high hopes. Ideas?

I had the same problem with the belt breaking and the roller not spinning. I read about giving the roller a couple of revolutions to seat the belt, so I put another new belt on. It still didn't spin. I realized it was the end cap that was not spinnin ... Eureka 2961AVZ Bagless Upright Vacuum

I have a Kenmore upright progrssive intell clean. For some reason it isn't sucking when I use it to vacuum. When I use attachments they work fine, but when I plug the hose back in after using the attachments and turn it back on it makes a weird noise and I can feel air blowing out of the back. Can you help me resolve this problem?

Open this manual to page 18 and clean all the filters listed to restore air flow.http://www.managemylife.com/mmh/lis_pdf/OWNM/L0908343.pdf ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0801 seconds