Having problems with your Vacuums ?
TriStar Vacuum Nozzle Pivot Elbow replacement
\015 I would like to know if someone could tell me how to replace this part. I have the new part but am clueless as to how it slips into the slots!\015
Look inside the two rear wheel slots. You will find the two retaining screws that hold the unit together.
Have a tristar exl. Want to install a new plug/cord however cant figure out to open up the vacuum? I found the 2 screws on the bottom, but after removing them, the vacuum still will not come aprt. Not sure if the white bumper guard is holding it together. Any ideas.
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
TriStar Vacuum Nozzle Pivot Elbow replacement
Look inside the two rear wheel slots. You will find the two retaining screws that hold the unit together. ... Vacuums
Power nozzle of my S3670 does not work (vacuum itself does work), the headlight bulb in the nozzle is broken. This happened in the past several times - we would bring the vacuum to service center - I don't know what they did other than replacing the bulb. I decided to go to ACE and buy replacement bulb myself, replaced the one in the nozzle - this did not fix the problem. I don't see any fuzes or anything in the nozzle. However, the manuals says to "Use only HOOVER part no. 27317307, which is a
... Hoover S3670 Bagged Canister Vacuum
Replace electrolux power nozzle elbow - Electrolux EL7020 Bagged Canister Vacuum
... Electrolux EL7020 Bagged Canister Vacuum
Replace on/off switch on rainbow D3 vacuum - Rainbow D3 Canister Vacuum Cleaner Power Nozzle Reset Switch Vac Cleaner Power Nozzle Reset Switch
... Rainbow D3 Canister Vacuum Cleaner Power Nozzle Reset Switch Vac Cleaner Power Nozzle Reset Switch
Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T
... Rainbow E series Canister Wet/Dry Vacuum
I just bought this vacuum at a second hand store. My girlfriend told me to grab it as it such a quailty product. How ever I can't find a model number or anything else. I need a manual please. Does it take bags? Do I need to replace the filter or just wash the one I have? It is black and silver, cannister. It also says big gary's vacuum system warehouse in surry British Columbia, Canada. It also says to use filter pow-r-nozzle 96. I have no idea of the year.
I suggest you google what you know. I dont think anyone here can suggest where you can get a manual for a machine you dont even know the name of.\015\012\015\012You ask about a bag ... I dont know ... is there one in it now? You ask abo ... Vacuums
Replace power cord for tristar vacuum a101r - Rainbow 75th Anniversary Canister Vacuum
... Rainbow 75th Anniversary Canister Vacuum
When I vacuum with the power nozzle, it keeps cutting off. Do I need to replace the hose or the power nozzle?
Not necessarily. It's hard to tell without checking it out. I strongly recommend taking it to an authorized Aerus Electrolux store and letting the service tech check it.\015\012If you have the "Sidekick", you can try using it. If it still cu ... Electrolux Epic 6500 Vacuum
I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth
When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums
How do I replace or repair my tristar power nozzle cordI don't know how to get to or how difficult it will be. there is a short in wire because it is separating from the power nozzle.
Dear kerri_clark,Can't you take a picture of tristar power nozzle cord that you mean.I need to take a look at this to assist you further more.regards,dm ... Vacuums
The power nozzle on my c141b model aerus electrolux canister vaccum no longer turns on. It was working when a large stringy object was sucked in. When hitting the red reset button, nothing happens. Is it likely that it is the fuse that needs to be replaced? All wires appear intact (I replaced the elbow assembly a few months ago.), and the sweeper moves freely.
It's not a fuse.\015\012Turn the power nozzle on it's top. Try to rotate the brush. If it won't spin, there's till something holding it. Remove all strings, threads, and whatnot from the roller. Try to rotate it again. If it still won't sp ... Vacuums
Need to replace belt in Kenmore Vacuum Power-mate nozzle
Hello,\015\012\015\012Here's what you'll need to replace a belt on a Kenmore canister vacuum:\015\012\015\012- Phillips Head Screw Driver\015\012- Flat Head Screw Driver\015\012\015\012There are two different ... Kenmore 23313 Whispertone Bagged Canister Vacuum
How to replace tristar vacuum fixed wheels
Need replacement nozzle for prolectrix 2000w vacuum cleaner
How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]
... Miele Vacuums
Looking for new belt for my electrolux guardian canister vacuum power nozzle marked model n106m . have been unasble to locate an appropriate belt replacement. Any suggestions?
This company is now known as Aerus. If you can't find their listing in the local yellow pages, follow the instructions on the folloing site.\015\012\015\012 ... Electrolux Guardian Bagged Canister Vacuum
Replacing power cord on tristar vacuum
... Tristar Vacuums
How to replace the elbow assembly on an aerus electrolux power nozzle
... Electrolux Vacuums
My hoover has no suction at the nozzle, though it has strong suction at the hose. This problem started after I replaced the vacuum bag for the first time.
There is a blockage behind the roller brush remove the roller plate and the roller and check the inlet hose for a blockage also remove the bag and chek the inlet to the bag for some type of obstruction. Don the Vacuum Doctor Alb, N.M. ... Hoover Tempo Widepath Upright Vacuum - Blue
I need a replacement belt for my central vacuum power nozzle.
Do you know the brand or model? If not you can get replacement central vacuum belts here:\015\012\015\012Replacement ... Vacuums
I have an Electrolux Epic 6500 SR vacuum and the hose end with the handle is separating. Power nozzle losing contact intermittently. Is this piece replaceable or repairable?
It is replaceable. Just take it to the nearest Aerus Electrolux store and the service tech will take care of it for you.\015\012Go to the following site and follow instructions to find the stores nearest you. ... Electrolux Epic 6500 Vacuum
I need to replace the belt on the power nozzle of my Hoover Dimension 1000 Model S3491. Unfortunately, I have no written instructions on how to do so. I purchased the vacuum cleaner in the mid-80s. Are the instructions still available? Thanks in advance.
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=566792\015\012Generic problem for all Vacuums\015\012I need to replace the\015\012posted by Deb in Iowa ... Vacuums
How do i replace the motor in a TriStar Vacuum?
... Tristar Vacuums
Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum