Having problems with your Vacuums ?

I am having problenms with my tention and need to know how to fix it, but dont know where the nobs are that do it


Answers :

Hi,

Please elaborate your problem providing us with more details and the complete make and model number of your product.

Thanks for using FixYa.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am having problenms with my tention and need to know how to fix it, but dont know where the nobs are that do it


Hi,Please elaborate your problem providing us with more details and the complete make and model number of your product.Thanks for using FixYa. ... Vacuums

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me


Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums

Sponge filter I have a kirby sponge filter for my Sentria shampoo system and dont know where it goes. It stop working and making foam. Kirby sent me the sponge filter saying this is what i need and i would know where it goes. I dont nor kind I figure it out. please help!!!!!!!


On the end of the shampoo tank where it attaches to back of motor where the bag is normally attached ... Vacuums

Need to fix level control part b-0133260 on bissell 7901-1 need to know how to fix it


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-P ProHeat Upright Vacuum

Okay i dont know what model it is all i know its a bissel steam cleaner all white and is on the floor kind and i need directions how to use it


There Is A Model Number On Either A Sticker Or A Plate On There Somewhere If You Can Find It Ill Give You A Link To The Manual. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I dont have a power cord and or foot pedal and need to know what I need.


Power cords can be found at http://search.totalvac.com/search?keywords=power+cord ... Vacuums

Hei, I have sewing machine Brother NV500D and got technical problem need to be service/repair. I'm now in Malaysia and don't have techinical/repair service for sewing machine NV500D. This is overseas model. In sewing machine screen display 'F04'. The problem automatic needle not function and part missing. I dont no how to fix this. Can't i got the instruction manual service picture if i can't fix own. please help me. thank you.


... Vacuums

I need to know how to remove the dirt container on the eureka bagless vacuum. It says that it is easy to remove, yet we cant figure it out. is there some trick to it that we dont know?


There is a lever at the bottom of the dirt cup,turn it to the left and pull out the dirt cup.note while you have the dirt cup out make sure you clean all the filters there is one right above the dirt cup pull out on the right side and there is a filt ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Hello! The suction in my Dyson animal is very poor. I discovered small holes in the internal hose, but even after a quick duct tape fix, still having issues...sounds like the seal from the canister to the vacuum is leaking air. I know I need a major repair but my mother in law is coming tonight! Any suggestions? ~Lisa


Or you can do this for free:\015\012\015\012http://www.ehow.com/how_5870417_modify-dyson-prefilter-suction.html ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Cant get my soap dispenser hose working on my karcher winner 10, any suggestion?, lost my instructions manual so dont know weather i need to be doing anything for it!


If you have not yet found a solution, then here are some steps to take.\0121. The soap dispenser only works on low pressure!!!!!!! So you have to\012 REMOVE the high pressure Sprayer so that all you use is the Trigger \012Gun without the Ext ... Karcher Vacuums

I need to change the belt on my Bissell Pro heat. I dont know how to get to it!


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I dont know how to thread, operate, or even handle any kind of sewing machine, and i need to find out how to do just the basics to do so


Follow the link below. It should show the basics on how to operate a sewing machine.http://sewing.about.com/od/sewingmachineinde ... Vacuums

Motor still runs--sounds like jet engine. do I need a new motor? or is there some sort of muffler that has malfunctioned? vacuum belongs to disabled mom---so trying to do work ourselves--cant afford much. dont see anything obviously wrong--but know nothing about electric motors.


This little vac I think is actually made by Samsung. If it is ROARING and vibrating, either the bearings or suction fan is in bad shape. Remove the lid as if to inspect the belt and see if there is a visible intake opening with a plastic fan rotatin ... Bissell 3590 CleanView Bagless Upright Vacuum

Hi, my circuit board resistors are burnt due to my re-wiring the resistor switch. How do I fix this - S3755 wiring diagram?? need to know the correct resistors or get a new board


The only way is to get a replacement board. even the dealers are not provided with that level of wiring diagrams. ... Hoover S3755 WindTunnel Bagless Canister Vacuum

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.


When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I HAVE AN IONIC BREEZE QUADRA PROFESTIONAL ONE SERIES SILENT AIR PURIFERTHIN WIRE IN THE BACK BROKE IN THE BACK AND IT DOES NOT WORK NOW. THE CO. FILED FOR BANKRUPTCY AND I NEED TO KNOW WHERE I CAN HAVE IT FIXED. I LIVE IN NEW JERSEY.


... Vacuums

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]


The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

D.d vaccum i have a dirt devil dynamite...i bought a new for it i put it on and not even 1 minute of using it the belt broke again!!!!i dont know whats going on do i have 2 put it on a certain way does it need grease or what!


Did you check the brush roll, if the ends aren't turning freely, then it needs to be replaced also. ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

I HAVE A HOOVER STEAM CLEANER MODEL#F5881-900 THE SOAP LEVER HAS NO TENTION,SOMETHING BROKE BUT DONT KNOW WHAT!


The valve at the bottom of the tank has a valve stem and spring, you may have to replace the spring maybe. \015\012\015\012Go to http://vacuumsuperstore.com/ ... Hoover Vacuums

Shutting off my vacuum has been shutting off in middle of use and i dont know why its like its over heating and i cant use it again for almost an hour is there a solution to this? or do i need to get a new vacuum?


It has a built-in temperature sensor which prevents it to be damaged from overheating. That's why it shuts down. It just needs to be opened up and cleaned thoroughly. Start with the hose if it has one and let someone who is handy with electric applia ... Vacuums

Kirby G3 I threw out my last bag for my kirby. I have an other model and now i dont know which type I need to get. I have 4 Style #2 bags but they are not the right ones... Help!


Beginning with the G series, G3 and G4 had round openings for the dirt intake. Prior models had oval so they will not fit, so find G3 or G4 bags and you will be set ... Kirby Generation 3 Bagged Upright Vacuum

TSC 441 JUKI NEED BOBBIN WINDER TIRE OR ORING DONT KNOW THE PART NUMBER SEWING MACHINE


... Vacuums

I have acquired a second hand amway CMS2000 it needs a new belt by the lookds of it but i dont know what this vac can really do is it a carpet cleaner as well and what are the products and how do i clean with it.


... Vacuums

I JUST NEED HOW TO OPEN MY NWD-B103F I HAVE IT BUT DONT KNOW HOW TO OPEN IT IT SAYS"WALKMAN,HOLD,POWER OFF"


For some reason, I think your problem got listed under Vacuum's--Maybe you meant to be listed under Electronics?-- Walkman is a clue to me, that this is not a Vacuum cleaner-Sorry--Mack B ... Vacuums

I need to replace the water tank for my SE01-G-7A biagiante steam xpress and dont know where to order one. Cant find Lentek website.


... Lentek Steam Xpress SE01 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0811 seconds