Having problems with your Vacuums ?
I have a volta ultima vacuum and the brush won't turn around anymore.
Tip the cleaner up and were the brush is theres a belt it is either slipping or broken replace. Undo cover over brush and undo brush lift out put new belt onto motor and then the brush and reassemble
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have a volta ultima vacuum and the brush won't turn around anymore.
Tip the cleaner up and were the brush is theres a belt it is either slipping or broken replace. Undo cover over brush and undo brush lift out put new belt onto motor and then the brush and reassemble ... Vacuums
For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.
... Kirby Ultimate G Bagged Upright Vacuum
Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi
Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum
I have a model 116.35922 beltless drive vacuum. The agitator brush will not turn with the vacuum running and the handle down. The brush turns by hand and the reset button has not popped. Ther is nothing wrapped around the brush, but it does feel to have some resistance when moving by hand.
Wich bags for vacuum cleaner kenmore model 116.35922 ... Kenmore Vacuums
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help
The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Brushes won't turn. have gotten out all thread etc, wound around the brush. have put vacuum in proper position and turned on the brush button
The brushes are usually driven by a belt that connects to one of the ends. They break. Check to see if yours has. ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum
I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha
... Eureka Smartvac 4870 Bagged Upright Vacuum
The brush on the bottom of the vacuum won't turn when in position to vacuum. I have cleaned the brush, there is nothing tangled around it.
Sounds like the belt is broke, when you remove the brush, be sure that all teeth are still on the belt and that it is not streched. Typically every major retailer will sell these belts usually 2 to a pack and under $10 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Kenmore vacuum- no suction, brush wont turn
Sounds to me like you have a plugged vacuum. Check all the way through. ... Kenmore 22812 Bagged Canister Vacuum
Kenmore vacuum - no suction, brush wont turn
Sounds like the vacuum is clogged and putting too much stain on the agitator, so I would clean out the entire passage way for the vacuum and replace the agitator belt, you must clean out all the hoses it is clogged somewhere ... Kenmore Vacuums
Bissell Proheat I have a Bissell ProHeat 12 amp 6 cleaning brush upright and it won't turn on anymore. We have done the basics like making sure the outlets work, etc. Changed it around to different outlets. It is not turning on. Any idea?
Things to check are the cord, switch, and the motor. ... Vacuums
Brushes wont turn and wont spray water - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
So i was vacuuming and pulled up a throw rub for about 10 seconds or less. i turned off the vacuum and and now the brushes wont spin. what do you think i should do? Thanks Tommy
You burned a flat spot in your belt - replace it. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I sucked up a sock into the carpet attachment of my electrolux 3500 series and the carpet attachment cut off. After the sock was easily removed (it was only wrapped around the brush part) I reattached the carpet attachment, turned the vacuum on and flipped the switch to turn the carpet attachment back on, but it won't come back on. How can I fix it?
Did you press the reset button? There will be a reset button either on the back of the unit just below the bulkhead or on the top side of the base.\012\012Locate the reset button and press; this should allow the carpet attachment to resu ... Electrolux Epic 3500 Vacuum
Brush wont turn..Pressed reset still no turn - Vacuums
If the motor runs and the brush doesn't turn, the first and best suspect is the belt. ... Vacuums
I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...
The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Vacuum brush roller wont turn - Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
You dont say if you checked if the belt is still whole so my guess is the belt broke(it could've fallen off and not be there at all but you definately need a belt) check that and let us know ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
The cleaning brush turns only sporadically. It will turn when we first press the button but then stops and starts when we move the vacuum around.
Sorry to read about your problem, I hope this helps you out.you need a new belt, and or you have string or something jamming the brushI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum
Brushes wont turn hoover f7412900 steam vac - Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum
... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum
My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.
... Dyson Vacuums
Brushes wont turn hoover 2000 dust master - Hoover Vacuums
Needs a belt visit www.stevessewandvac.com they have on for your unit. ... Hoover Vacuums
The brush wont turn on my dyson DC 14 - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Sounds\015\012 as if you need to replace the brush belt.JimLet me know if this helps. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
The vacuum sucks good, but the brush on the bottom wont turn, and the belt seems tight
Even tough the belt is intact it still might need to be replaced. Here is a replacement:Dyson DC14 Belt and Manual ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
The vacuum suction still works but the brush wont turn. It still looks like the belt is intact and attached properly.
The problem with Dysons is that the belt breaks and sits in position.If you can turn the brush by hand, with little or no resistance then I would say the belts broken.If in doubt take the cover off and look. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum