Having problems with your Vacuums ?

Singer 4526C appears to be jammed. Hand wheel very stiff to turn and when pressing foot control machine moves very slowly.

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Singer 4526C appears to be jammed. Hand wheel very stiff to turn and when pressing foot control machine moves very slowly.

... Vacuums

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Have oiled my Bernina 707 minimatic 1970 sewing machine and I have power when I press the foot pedal, but when the handwheel is tensioned none of the mechanism under the free arm cover plate moves. I went to sew something and the needle jammed. I took the covers off and there is no debris - it was all oiled and left overnight. Now the Take up lever doesn't move and is in the down position.

... Vacuums

I have a Juki serger mo-634de that I am borrowing from my sister in law. She doesn't have the manual, but just got it back from the shop in good working order. I have threaded the machine, and when I manually turn the dial, it appears to stitch properly, but when I press on the pedal, nothing happens. No sound from the motor, no movement with the needles, nothing. Help! (c: Power is working, because bulb turns on.

... Vacuums

I recently purchased a Sunbeam Artista EM5900 model coffee machine. I plugged it in and pressed the 'Power' button only to find the power go out. I understand this is short circuiting, so I went and turned the power back on. I then moved the machine to a different powerpoint and plugged it in - the same problem happened and I have tried it countless times on various other powerpoints. Help please?

Try it in a different part of the house. If it works then you have too many things running in the kitchen.\015\012If it still blows a breaker then it is shorted out and needs to be returned. ... Vacuums

I cannot get the sprays from either the bottom or the handpieces to work. I only get a short "gurgle" of fluid when I first press the controls. I have cleaned both the top and bottom cap and insert parts, and I have turned the machine off and on numerous times, have allowed it several minutes to warm up. But still no luck. Bissell Turbo 2X 9500 series (3 years old) D B Davis Camas,WA

It sounds like the pump has malfunctioned. I own a Bissell Big Green Clean Machine.You can actually order a 50 foot hose and run it from the sink to the hand piece or the part that is supposed to spray to the floor. This hose can handle ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Elna 500 Club sewing machine - no power when foot control is pressed

... Vacuums

My Electrolux Epic 6500 SR will not turn off by pressing on the switch button. I took it apart and removed the switch assy. I can maunually turn it off & on by pressing the rocker arm on the switch assy. It appears that the problem is with the big blue operator button, not the switch assy itself. The button does not seem to press down enough to cause the rocker arm to switch. The button has a "U" shaped wire that presses on the rocker arm and it may have some broken plastic details at the b

WOW !!! Finally You are dead on, absolutely 100%.... good work!!!.Get only a genuine new switch button with spring from an AERUS Electrolux dealer and reinstall. Then carefully reassemble the entire body and wiring harness.Con ... Electrolux Epic 6500 Vacuum

My Dyson DC 24's beater bar switch didn't actuate and the beater bar didn't turn. When I brought it to a certified serviceman he told me that a wire interferred with the switch and all he had to do was move the wire out of the way of the switch. At the time the machine was under warrantee and it didn't cost me anything. Now however, the machine is out of warrantee and the problem has returned. Does anyone know how to access the switch and move the wire out of the way?

Hi- I had the same experience but it turns out there's a small trip switch if you've taken the brush out to clean it, it needs to be reactivated by pressing the small red button to the right of the brush... took me a year to figure this out! Been mea ... Dyson Ball DC24 Bagless Upright Vacuum

Kirby Sentria Hi, I have a new Sentria & used it for the first time today. It was going fine & then I could smell smoke & it started to make a loud noise so I turned it off quickly. If I turn it on it immediately starts making the noise again & I can see it is all lit up inside like something is burning or sparking. I have checked the roller & it is moving & I have checked the fan which is moving & doesn't appear to be damaged in anyway. This product is from the US & we are in the UK & we are us

Sounds like the motor burned up. not sure if travel adapters will handle a large load like a motor, around 8 or amps. power needs in US are 110 volts ac, 60 hertz.I believe UK is 220 volts and 50 hertz. usually when a vac is brought to eu ... Kirby Vacuums

The presser foot is stuck in the down position on my sewing machine. The lever goes up and down but the foot will not move. Help! I have an old Kenmore 22 sewing machine. Probably got it around 1990. The model number is 385.17622.

If you open the left end of the machine .. look inside above the needle and to the back .. you will see a pivot bolt that has either come loose, broken off or fallen out .. replacing that bolt should fix the problem .. ... Vacuums

IjI need a new foot control for my old Elna model. It is an Elnasuper 62c/H401048. The foot control has the ID# of 447300-1, a new power chord would be great to. I have had this machine for40 years.

... Vacuums

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th

... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

I have a roomba 530 pet series. It appears that the brushes aren't turning. They are free of dirt and debris and move easily when manually turned. But, You can tell there may not be a motor turning, because the roomba is more quiet than normal when you turn it on. Also, the hair just collects along the bottom of the brush and doesn't get pushed into the bin.

The belt either broke or has come off the track.... this should be easily accessable from the underside of vaccuum ... iRobot Vacuums

Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance

Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

There was no category for sewing machines....so I picked small appliance. When I depress the foot control E1 flashes on the LCD screen. I've followed the steps in the manual but it continues to flash E1. The machine will not operate. This is a brand new machine. I've used it only 3-4 times in the last 2-3 years. It worked perfectly until now.

What make and model of sewing machine do you own ? the more information you provide the easier it will be to assist you . ... Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have a janome 9000 sewing machine and while moving have lost the presser foot and foot A, how can I replace them? heather

Replace it with a new one which is availble in market.or find out the people who sell the same product in second hand. ... Vacuums

The Dyson Animal won't turn on or off. The red power button doesn't control the on/off for this machine any longer. Once plugged in, the vacuum will work and the power cord must be unplugged to turn it off. Any help would be appreciated.

The machine needs a new switch. The switch is stuck to the "on" position. ... Dyson DC05 Bagless Canister Cyclonic Vacuum

The cleaning brush turns only sporadically. It will turn when we first press the button but then stops and starts when we move the vacuum around.

Sorry to read about your problem, I hope this helps you out.you need a new belt, and or you have string or something jamming the brushI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

Roomba Discovery Roomba is fully charged and cleaned with sensor wiped clean. When turned on it it sounds normal and commences to go, but it then acts like it is putting on the breaks, spins, tries to go and manages a short distance and breaks again, just not making any progress because it keeps breaking after a foot or so and turns and tries again. Sometimes is gets so stuck from moving forward at all, like it is stuck in one spot just trying to go while seemingly surrounded by barriers. Somet

I had the same back-up, turn, move forward a couple inches, backup-up, etc. problem. Try cleaning/cutting the hair, etc. out from around the brushes, as well as around the ends of the brushes. Also, try a Q-tip to clean out the four pair of sensors ... Roomba Robotic Floor Bagless Vacuum

Sewing machine Viking emerald 183 lost manual in move. how to move needle position from side to side within foot ? Any on line manuals? TU ---gina

... Husqvarna Vacuums

Bumper sensor appears to malfunction - machine moves 6-8 inches and reverses just as if it ran into an object, then it moves 6-8 inches and changes directions again, over and over. if i count correctly, the error beeps count to 8 or 9 (they come too fast!).

... iRobot Roomba 550 Vacuum

Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ

I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums

We have the bissell quicksteamer and as I was shampooing I began to notice something burning so I unplugged our machine immediately; then my mom and I started cleaning all the filters assuming that could be the source of our problem and yes it was a little dirty but I suspected that it would take more thant that to cause our machine to somke soI turned it upside down and noticed there is a cable of copper threads that appear to have some type of rubber or plastic insulation tubing around it but

Was the exposed copper wiring on the electrical cord? If is then replace the cord. The main problem with this model is that Bissell obsoleted it as well as parts for it. But if all you need is a cord, you should be able to get one from a repair shop. ... Bissell 1960-3 QuickSteamer Plus Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0755 seconds