Having problems with your Vacuums ?

Norelco razor 6867xl - am planning to replace battery pack. Would be easier to solder if I could remove the whole circuit board system from the hard plastic case. How do you release the metal clips?

Answers :

The whole circuit board is removable, and I would recommend removing it from the whole external case to work on so nothing is damaged by your soldering iron.
\015\012Battery : 2x NiCd AA
\015\012Battery capacity : approx. 700 mAh
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Norelco razor 6867xl - am planning to replace battery pack. Would be easier to solder if I could remove the whole circuit board system from the hard plastic case. How do you release the metal clips?

The whole circuit board is removable, and I would recommend removing it from the whole external case to work on so nothing is damaged by your soldering iron.\015\012\015\012Battery : 2x NiCd AA\015\012Battery capacity : approx. 700 ... Vacuums

I have an Eureka Express canister vacuum - I believe it's model 8284 - that just stopped working. Plug it in, turn it on, and absolutely nothing happens. I took it to the local sew and vac place and they say it's a circuit board that is no longer available. I've looked at all the parts lists and diagrams for that vacuum and I would swear there isn't a circuit board there. (I wouldn't have even thought that in 1989 they would have used circuits.) In any case, I absolutely love this machine a

Given the age of the machine weighed against you fondness for it, unless you can find a fault with either the switch or the cord, there is little else that can be done. With time the electrical lead can break down and one o ... Electrolux Vacuums

Circuit board i have searched far and wide looking for a circuit board for my fantom cyclone xt, so far i can't find one .. is their anyone who can can locate or sell me one of these hard to find items. i am at the end of my rope ! any help is appreciated, thank you for your time TOO SLIM

Http://www.vacmall.com/supplies.asp?Brand=Fantom&Model=Cyclone+XT ... Fantom Vacums Cyclone XT Upright Vacuum

Vacuum cleaner: AEG electrolux Cyclone XL bagless; the plastic clip (release button) broke off the lid of the dust container. Do i need to replace the entire dust container or can i just buy a new clip?

... Vacuums

I have Dyson DC05. The plastic clip from handle to the metal pipe is broken. Can this be repaired or do I need to replace the whole metal pipe section? If so where can I do this.

Dear Madam/SirThis is very simple problem. the problem can be solved in a very simple manner.As you have told me that the plastic grip from the handle to the metal pipe is broken.You Can do it near by any welding s ... Dyson Vacuums

How to change the bag in the Oreck XL hand canister vac? I can't seem to get the plastic piece back in before locking with the metal clip. Is there a diagram to show me?

... Oreck Vacuums

Loose faucet the whole unit is loose at the base. I can not get the plastic nut underneath to snug up, It just spins. I'm guessing it's stripped, but has been loose since putting in granite counters. there is a metal 3/4 clip that is just hanging there loose, but don't see if or how it attaches. Any advice, thanks

... Grohe Ladylux Plus 33 759 SD0 Stainless Steel Pull-Out Kitchen Faucet


I got a new remote switch box to put inside the fan, wiring in the lights was a snap but i have a red pink grey and yellow wire that control the fan and i should have tested the wires before i unplugged and re wired the light because the fan was runn ... Vacuums

Hi I have a eureka 410 series lightweight upright and I took it apart to clean the dust from inside and on the very bottom of the handle the is a metal clip and a white straight plastic peice that fell out and I dont know how it goes back in.

... Eureka Whirlwind 410 Bagless Upright Cyclonic Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I fear the motor has failed on my Electrolux Oxygen EL6988D. Just six months after the warranty expired, I was vacuuming when it suddenly stopped. There was no blockage in the tube and it wasn't working hard or long . . . it just stopped. I looked around the Internet and it appeared that many similar Electrolux units have a fuse. I hoped my problem might just be a blown fuse, so I took the machine apart. There are two small printed circuit boards, but no fuse. There is an in-line

Hi,\015\012\015\012I don't think you need a new motor, but please stop testing the machine with live power. It's dangerous and unnecessary. Your tests indicate to me that the motor is fine and your thermal-fuse - I think this is wh ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I have replaced the circuit board twice on my hayden 2400 and after working for 24 hours the circuit board then fails, with no signs of it tripping. Everything is wired in correctly the supplier is unsure of the problem but leading up to me replacing the circuit board the machine itself had became intermittent switching on and off while hoovering

Disconnect the wiring from the unit, and go back and plug in your hose. \012\012Get a volt tester and test the voltage coming from the lines at the machine. It should read 0 volts. Check both AC and DC voltage. \012\012Also, c ... Hayden Industries SuperVac 2400 Central System Vacuum

Dc15 fuse The roller brushes on my dc15 stopped working..I checked the obvious and then noticed that the 2 amp fuse was blown on the circuit board . I've replaced it with the same type bought from Maplins but it keeps blowing .. I tested the yellow an blue wires leading from the circuit board to the roller brush head and the are in tact and I can run a current through them ... Any thoughts from anyone .? Your help would be. Appreciated thanks Lee

Hi Lee,I'm sorry to hear you're having difficulty with your DC15. If you'd like some help, please give us a call on 0800 298 0298 - we may be able to resolve the issue with some troubleshooting over the phone.Best wishes,Jack ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

The battery will not charge in the sweeper. I can remove the battery and wire it to the power supply for charging and it will charge up and run the sweeper. So the power supply and the battery are both good. Obviously there is a circuit failure in the on board charging control. Anyone know a fix or a likely faulty component? I had a shark handheld about 8 years ago and it developed the same problem. I examined the little circuit board inside but saw no visible indications that would isolate t

... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

My danby kegerator model DKC645BLS controller circuit board corroded and no power to the compressor,I already have an external temperature controller,can I just bypass the controller and circuit board

... Vacuums

My circuit board has a short on the soldering for the DC rectifier that supplies the carpet cleaning motor. Where can I order a new circuit board. Miele S251i

Just a suggestion, but you could try to re-solder the connection on the board. some of the circuit boards did not have enough solder on the board coming from the factory. That being said, if the component is damaged due to the burning, I ... Miele S251i Plus Bagged Canister Vacuum

Have a Miele S658 Blue Moon that cuts out intermittently, sounds like most of the solutions to similar problems indicate the circuit board has gone bad in the hose mechanism.......can just the circuit board be replaced or does the entire hose have to be replaced?

Probably needs a new hose. ... Vacuums

Riccar 1700 melted connector to circuit board...

It might be an easy fix but should be done by a qualified Riccar dealer. ... Riccar Vacuums

I shipped my brother PE 770 embroidery machine purchased sept of 2010, to a lady who perchased it on ebay. Had used only once. Everything worked fine.I shipped in the original formed styrofoam box. I removed the embroidery arm, releasing the locking plastic hook holdind the machine and the arm together. When to lady removed the machine first in the original plastic shipping bag, two parts fell out. Her photo she emailed showed a black plastic piece with two holes or pivot points.also a silver me

This is a link to the manual for this machine. Do you see a picture in the manual of the parts you are describing? Reply with a part number and I will do my best to help. ... Vacuums

I'm using Miele Medivac vacuum and I just sucked in a small plastic eye drop container by accident(I sometimes take off the brush part to **** in 'small enough' articles). And it is jammed in the part where the plastic hose connector bends. I think I can take it out if I can just disconnect the long necked plastic hose connector that connects the metal wand part and the hose part. Is it designed to be disconnected or should I not even try it?

I love the fact that the filter bleeped out s.u.c.k ha ha! ... Vacuums

Jun 24, 2010 - Jun 24, 2010 - Needle not bent/ new needle not answer. I finally conclude that the entire bobbin case is ROTATING in its seat, which jams the needle. The "projection" is against the "spring" when I install it, but I can rotate the bobbin case PAST the spring without trying very hard. Bobbin case MIGHT get held in place better if it were closer to me (front of machine). I feel it is still not out from under needle plate as shown in diagram, but can't keep it closer to f

Hi,Your problem dated 24th June 2010 was re-posted today. If it has been already resolved, kindly ignore this message.Thanks for using FixYa ... Vacuums

There is something stuck in the handle of my Miele vacuum. I unscrewed all the screws hoping that I could remove the hard plastic handle from the hose. I was only able to flip up a piece of plastic where the switch is. Should I pull harder to pry the plastic apart? I was afraid I'd break something. Thank You, Chrissy

... Miele Vacuums

Bissel Proheat 2x circuit board

Use this link: http://www.4cleanerfloors.co.uk/cgi-bin/product.pl?PID=1278118_amp;brand=Bissell_amp;model=_ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Broken black plastic of hose handle where it meets the metal part

You are going to have to contact the manufacture google the name and model # and serial # appliance parts places wont stock the specific part good luck . Tom ... Karcher K DS 5500 Vacuum

Dyson DC07 - broken 'Contact Head' release clip

Hi Wombat64\015\012\015\012We noticed you are having difficulties with your Dyson vacuum cleaner. We think we can help, simply call our Customer service team for free on 0800 298 0298 between 7am - 10pm, 7 days a week.\015\012 ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0464 seconds