Having problems with your Vacuums ?
Kenmore Central Vacuum System-electrical o.k. but suction function not working. No noise from canister.
It could even be a bad motor if its an old kenmore system. If its more than 10 years old it maybe worth getting a whole new tank over just a motor.
There should be a switch on the canister, for manual or automatic. Switch it to manual and see if it comes on. If it does, then there maybe a bad relay. If it doesn't, then there is a problem inside of it, motor, pc board, would have to be checked. Without the model number, not sure what components are inside without the model number to look it up.
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Kenmore Central Vacuum System-electrical o.k. but suction function not working. No noise from canister.
It could even be a bad motor if its an old kenmore system. If its more than 10 years old it maybe worth getting a whole new tank over just a motor. ... Vacuums
I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!
Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum
Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would
... Hoover L2310 GUV Central System Vacuum
My home has a central vacuum system hook-up but no vacuum installed. My friend upgraded his central system and gave me his Eureka Mega Boss central vacuum system and the accessories, including the pow
The power head requires 120 Volts. Some hoses have a receptacle in the handle for the power head plug, and the hose has a cord at the wall inlet end that plugs into a receptacle. Some hoses have a plug at the wall inlet end that plugs into a 120Volt ... Eureka 1810 Central System Vacuum
I have a central vacuum system. When I disconnect the hose from a wall outlet the central canister does not shut down dispite my turning off the vacuum at the handle of the hose. The only way I can get the system to shut down is to pull the plug at the canister. What gives? Rob
What I'm hearing is the canister(Not the Powerhead) portion of the unit is running all the time unless you unplug it. this problem could be caused by a short in one of your low voltage lines running through the house. To determine that just unplug on ... Vacuums
My upright kenmore progressive vacuum will not suction up when using the sweeper. It will suction things when I use one of the tools. I have put in a new bag and have tried to see if anything is blocking the bottom. It sometimes makes a very loud noise when I try to vacuum. If I press the intell clean on and off yellow button the noise may go away but it still does not work.
Double check hose placement, making sure you have the hose inserted into the correct slot. The long attachment nozzle stores in the front hole on the right, and the sucking hose inserts into the rear hole on the right. I know this is too simple of a ... Vacuums
Beam central vacuum system just stopped working
My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a
Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
No Suction I have the Eureka Upright Vacuum. I have no suction when doing regular vacuuming but it seems to have function with just the hose. Also, the height adjustment doesn't seem to work at all. The vacuum has only be usede 3 times. Thanks
Is your brush roller turning? unplug the vacuum and see if you can turn the brushroller by hand.if it turns real freely the the belt is broke ,if its real hard to turn then something is caught up around the bearings on the ends of the roller.my sugge ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
Hello, my Kenmore 27514 canister vacuum only works on the hard floor...the carpet suction stopped working while I was using it. Is there anything I can do to fix it or is it necessary to take it in for repair? The vacuum is only 1.5 years old. Thanks. Susan 702.340.8015
You need to replace the belt that drives the beater bar. You can do this yourself very easily. If you need help, let me knowJim ... Kenmore 27514 Bagged Canister Vacuum
Hello, I have an electrolux tweanclean EL7055A vacuum canister, and can't switch it on anymore. The cleaning system is working well (so the power is ok) but the command which is not directly in the canister seems not working. What I can do to test if the problem is here ?
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=636174\015\012Generic problem for all Vacuums\015\012Hello, I have an Electrolux (by 2 users)\015\012Po ... Vacuums
The floor head is no longer working. The canister works, there is suction, but the floor head is dead. No lights, suction control switch inoperable, no headlight, nothing. It just stopped one day during a vacuum session. Thanks.
Hi poohbear4760...\012Check your wiring going to the vacuum head, some vacuums have a problem with corrosion on the plugs...take your connections loose and lightly sand with fine grit sandpaper the metal ends.\012Plug the wires back toge ... Vacuums
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio
Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum
My beater bar on my Kenmore 116.25615506 canister vacuum keeps turning on and off when I vacuum rugs. The suction continues, but the beater bar seems to be shorting or whatever. I checked the belts and they look like new. Any suggestions? The rest of the vacuum works fine!
... Kenmore 25512/ 25513 Progressive Canister Vacuum
I have a Dyson 39 Animal Canister vacuum that was working very well on my laminate wood floor. I have had for two months with no issue. Recently the suction is so strong that vacuum takes effort to m
... Dyson DC39 Animal Canister Vacuum
We have a Kenmore canister vacuum cleaner and the power in the floor component (rotating brush, etc) is no longer functioning. The vacuum is producing suction, but does not seem to be providing power to the floor component.
The problem could be with the power head itself or the hose providing the power. If you can turn the unit on from the handle, then its not the hose and you need to get a new power head.. ... Panasonic Kenmore Canister Vacuum Vacuum
I have central system vacuum cylinder engine is working but on the wall conection nothing is working.
Check to see if the low voltage wires are attached to the tank. At the tank, if you switch it to manuak, will it work then? If so, then replace the relay board that is inside the tank. Is the problem at all outlets, or just one of them, if just on ... Hoover Vacuums
While vacuuming with a beam central vacuum system it suddenly just lost power and suction.
... Beam Industries 875 Classic Central System Vacuum
I had to empty the canister and when I put it back on and turned on the vacuum, the suction does not turn on. The brushes are rolling and the attachment suction works fine. Any suggestions?
... Eureka 431A Optima Bagless Upright Vacuum
We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu
Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum
We just purchased a house with the Easy Flo central vacuum system. When we opened the canister to empty it we discovered a bag or something hanging down into the canister. It is covered with dust, dirt, hair and who knows what. Do we change it or clean it?
Hi Trudi,Yes, you can wash it in warm water with a mild \015\012detergent. Be sure that the bag is completely dry before putting it back on.Should you ever decide you want to replace it, just do a google search for your vacuum ... Easy Flo EF1500 Vacuum
Hi we have a central vacum system (canister). Sometimes when you plug in the hose it works fine othertimes it doesn't work?
There are two types of coupling that plug in. One has a solid metal ring. There are two metal electrical **** inside of the inlet. When you press the coupling into the inlet the metal ring completes the circuit. If the ring or the **** are badly ... Vacuums
I have a 10 year old AirVac central vacuum system that has worked until this morning. As I was using it this morning, and turned it off for about five minutes it would not start again. The tank in the garage (that accepts the dust) sounds like it is just huming not working. What is wrong?
Sounds like the motor finally siezed on you. Motor is trying to turn but won't thus the hum. Do not allow the vacuum to stay on like this as it may cause a fire. Requires a motor replacement. ... M&S Systems ZX7000 Bagged Central System Vacuum
LlllSteam vac ws working very well--shilfted to using hand vac on furniture--when I shiftead back to wanting to use the floor vacuum using the 6 brushes and the floor vac system, the r6 rotaty brushes will not turn or function. What do IO havae to do to get them to turn and function? The lever on the side ils set for carpet terrain. What do I do now to get brushed to turn and scrub as they should and did previously. James Yerges 1'630-232-2798 JMYerges&comcast.net
What is the exact model number of that unit. There are several with that name. The only things that it could be are the handle mechanism that activates the brushes or the indicator is not working nad the level that selects the brushes is not working. ... Hoover Vacuums
DAS ducted vacuum. The machine starts up, but no suction at inlet. inlet at central vacuum system operates fine.
You either have a clogged line or, your tubing joints aren't sealed. ... Vacuums