Having problems with your Vacuums ?

TOOK MY ELECTROLUX EPIC 6500 CANISTER MODEL 1762 APART TO REPLACE CORD REWINDER. TO MAKE A LONG STORY SHORT,MOST OF THE WIRES CAMES OFF OF HEIR CONNECTIONS. NOW CAN'T FIGURE OUT WHERE THEY GO WITHOUT A SCHMATIC. CAN ANYBODY HELP. THANKS CATHY


Answers :

Hi,
\015\012
\015\012I will try to find a service manual for you.
You can ask for online support here and eventually ask them service manual which contains schematics
\015\012
\015\012regards
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

TOOK MY ELECTROLUX EPIC 6500 CANISTER MODEL 1762 APART TO REPLACE CORD REWINDER. TO MAKE A LONG STORY SHORT,MOST OF THE WIRES CAMES OFF OF HEIR CONNECTIONS. NOW CAN'T FIGURE OUT WHERE THEY GO WITHOUT A SCHMATIC. CAN ANYBODY HELP. THANKS CATHY


Hi,\015\012\015\012I will try to find a service manual for you. ... Vacuums

Rented triumph 430 and cant figure out how to work the accessories. I have the vac hose and a smaller hose attached ro dispense solution. There appears to be no way to plug in the smaller clear hose. Was I supposed to get another length of hose to connect from fitting on accessory to machine?


Yes don. call the store where u rented and tell them. ... Vacuums

I need to wire the switch to my coleman 2234 push button 12v water pump in my camper trailer. it is wired to the battery now with the "red" connected through a small fuse. i just cant figure out where to wire the on/off switch to.


Hi there. When connecting a switch, it is important to remember that a switch will only "break" the positive (+) circuit, while the neutral wire will go directly to the battery. So, basically split the red wire coming from your pump and connect the s ... Coleman Vacuums

Cant figure out how to use the hose attachment,it connects at the top at the duster and at the floor,how do i change it to use the hose only?


... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have an old Friedland door chime (approx 30 years old). It has 5 terminal screws to connect wires. They are labeled 0-4. I removed the chime during remodeling and would really like to reuse it. I did not label the wires and where they connect when I removed it. I can't figure out how to wire it. I contacted Friedman and they were of no help... didn't have information on chimes that old. Can you help with how to wire the chime given it has five connections screws with no labels other t


... Vacuums

Cant Figure Ou What Hose Goes Where?


I don't know if its the same machine but I found this site, it provides a link to a picture of the tube routing:http://c.managemyhome.com/mmh/answers/Answers.action#l4q145526 ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My Oreck XL has worked very well until the power cord was pulled out of it. I figured how to hook up the hot but can not figure out the neutral connection. any ideas?


If there are two wires it doesnt matter normally white 2 white and black 2 black if its 3 wire than green is ground and the other 2 dont matter thanks Don ... Oreck XL Ultra Bagged Upright Vacuum

How do i take the old belt off of my dyson dc 14? cant seem to figure out how to get the roller separated from the machine because i cant get the old belt off.


Go to: Dyson web site or \015\012\015\012 http://www.repairclinic.com/0100_24.asp\015\012\015\012There should be 4 to six screws holding the ... Vacuums

Sweeper belt Hey , i own a fantom thunder sweeper and recently my belt keeps slipping off, i've disassembled it and put it back on a hundred times but it keeps doing it after a few minutes of cleaning , Am i missing a part to hold it on or somthing else wrong i've cleaned it and checked all the ports just cant figure it out and cant find any info online thanks for your time tina


Greetings from GoVacuum.com,Have you replaced the belt with a new one yet? You may want to try replacing the belt, as with flat belts like the Fantom Thunder, they do stretch out 4 -5 inches after time. We in fact recommended replacing ... Fantom Vacums XT450K Upright Vacuum

I have a dyson animal dc17 vacuum and it totally died. Now I can't figure out which wires go where when I install my new motor. (motor #: 160906G) Do you happen to know where the various color wires go or a place I can see a diagram of the motor with wires attached? I should have taken a photo of it before tearing out the old motor. I don't know where to connect the three coming out from the upright portion of the machine and the red seems to go to a switch (?) and there is a black (connected t


... Vacuums

Cant figure how to use shampooer for e series rainbow


... Rainbow E series Canister Wet/Dry Vacuum

I cant figure out how to remove the housing cover


Hello,\015\012\015\012Here's an excellent video showing you how to replace the clutch on a Dyson vacuum cleaner. It's a moderately difficult repair, but this video really helped me the first time I had to do this repair. I hope this he ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I need to know how to remove the dirt container on the eureka bagless vacuum. It says that it is easy to remove, yet we cant figure it out. is there some trick to it that we dont know?


There is a lever at the bottom of the dirt cup,turn it to the left and pull out the dirt cup.note while you have the dirt cup out make sure you clean all the filters there is one right above the dirt cup pull out on the right side and there is a filt ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Oreck xl9300 Bought a new motor but cant figure how to pull off the metal fan from the old motor. Is it muscle or a trick?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=19810&thid=767429\015\012Oreck XL9300\015\012Posted by Cubfan70 on July 10, 2008\015\012Bought a new motor ... Oreck XL Ultra Bagged Upright Vacuum

I HAVE A HOOVER POWERMAX CYCLONIC FILTRATION CLEANING VAC 12AMPS AND I CANT FIGURE OUT HOW TO REPLACE THE BELT AND I LOST THE INSTRUCTION BOOK PLZ HELP


... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

The belt is broken and i cant figure out how to get the wheel of to put a new one on


The control height adjustment knob should simply pull off - grasp it gently and pull off. Then locate the screws on top of the floor head to get into the belt area. ... Euro-Pro NV31 Infinity Vacuum

The back wheel came off and i went to put it back on and the other wheel that connects to the mechinism/gear height ajustment that goes up/down with a spring in it came off as well. i have been looking for a schematic to put it back together but cant find any.


You do not need schematics, it is fairly easy. Clean and lubricate the teeth on the inside of the front wheel shaft assembly. Insert the spring into small pedal and place the pedal designated opening on the Kirby front fan casing with teeth facing ou ... Kirby G6 Bagged Upright Vacuum

Vacuum has burning smell like a belt but cant figure out how to tear apart


If you flip the Dyson upside down you will see ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Cant figure out how to use the shampoo feature on the kirby sentria


Try this link for a step by step guide...http://reviews.ebay.com/KIRBY-CARPET-SHAMPOO ... Kirby G6 Bagged Upright Vacuum

Cleaning uphoustry I cant figure out how to attach the hose to clean furniture


Gently wipe off a section of the leather upholstery, use another slightly damp washcloth to remove the soap, then buff with a dry washcloth. Repeat this process over the entire upholstered area. In between cleanings, vacuum leather u ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I can't get the cleaner to work, i don't think that I have it connected right. I can't figure out how to lock the top and water holder in place.


That one is a little funny to get on right.\015\012\015\012There is a lip on the lid towared the front. That lip has to hook under the tank first and then pull the lid over top the back and latch it on.\015\012\015\012Good Luc ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Loosing suction I am loosing suction on my vacuum. I have only had it for about 6 months and cant figure out what is wrong. Can you help?


Well you did not state what model and brand this is, but usually if the hose or the dirt inlet by the brush roll gets clogged, then you lose suction. If you can't figure it out, usually there is a year warranty, take it in for warranty service. ... Vacuums

Cleaning uphoustry I cant figure out how to attach the hose to clean furniture dont know how to hook up attachment to clean upholstery


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=40488&thid=539310\015\012Cleaning upholstery\015\012Posted by renee123456 on Apr 23, 2008\015\012Hoover ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I am trying to remove the motor in my Kenmore canister vaccum but cant seem to figure out how to get it out.


Without the model number, I don't know which model you have. But you can go sears.com, click on the parts link, then put in you completer model number, choose the cannister or main unit, a parts list and a picture diagram will come up, you maybe abl ... Kenmore 22812 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0338 seconds