Having problems with your Vacuums ?

I need a replacement small juicer cone for my Breville JC7 'Squeezed' juicer. Narelle Jensen 0418 153651 [email protected]

Answers :

Hi, you have to contact Breville Care on 1300 139 798, 0800 273 845 to make a request for the part and you will be directed to the nearest Breville outlet in your area..

Take care
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need a replacement small juicer cone for my Breville JC7 'Squeezed' juicer. Narelle Jensen 0418 153651 [email protected]

Hi, you have to contact Breville Care on 1300 139 798, 0800 273 845 to make a request for the part and you will be directed to the nearest Breville outlet in your area..Take care ... Vacuums

I think I need to replace the main battery in my small floor vac - the one that can be hand held like a dust buster or work like a small floor vac. I need to know how to remove the battery and replace it with what kind of new battery..

I see my sense of humor is not appreciated...it was only a joke. Anyway, here is what you do: First, slide the battery cover off the bottom of the hand held unit. Remove the battery from the motor housing by pressing the tab on connector “A&rdq ... Vacuums

I have a 25 year old juicer blender model #mj-130p. I lost the plastic piece that pushes vegetables into the juicer. How can I get a replacement. Thanks

It is going to be very difficult to find the actual plastic piece you are looking for since the juicer is so old. I personally recommend you use something like a generic muddler, something like this and you should be good to go: ... Panasonic Vacuums

My DC 17 is plugged. I can see through the small hole in the top blue "flower shaped" that the holes at the top of the canister are plugged with hair & dirt. I cannot see anyway to get to these small round holes. Is there a way to remove the top blue "flower shaped" piece? I have removed the inner cone from the clear canister but still cannot get up underneath.

Please kindly follow the steps below to clean your vaccum cleaner,1.) Remove the clear plastic handle. You\015\012will have to take out two screws and then unclip from the from the\015\012front. It's stiff, I gently used a flat head screw drive ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover pet cyclonic upright model uh70085. the brush won't spin, I thought maybe the small belt was stretched, I ordered the correct replacement belt and replaced it, I still have slack and the brush won't turn. the floor and brush adjustment seems to be working correctly. Thanks, Tom

... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

I have a Bissell Model 8905 Carpet Cleaner. I was going to replace the belts because the pump belt broke, but when I turned the machine over, a small piece fell out. It looks like a tensioner arm because it has a small round part at each end on opposite sides of an arm that has an offset or "dogleg" in it. I am looking for an exploded parts diagram to determine what the part is and where it came from.

... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a Holmes HM495 humidifier and the plunger that releases the water into the base has rotted. Holmes indicates they do not sell parts which is insane. Any advice on replacing this small part as I do not want to have to replace the whole unit

... Vacuums

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1

As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

Replace Hoover Slider belt and reassemble. Online schematics too fuzzy and small to read. All parts fell out when trying to replace belt.

Here is a link to the belt you need and the manual, hope it helps.Hoover S2105 Slider Belt\015\012\015\012\011\011\011\011\011\011 ... Hoover S2105 Slider Bagless Stick Vacuum

7901-1 need to remove brush and replace small belt

Follow the manual instructions! You just pop a little tab on top of the vac above the wheel. It says someting about belt replacement.\015\012Just be VERY careful...I made it harder than it was (not checking the manual) and pulled the roller o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

The small button on the hose handle is missing, I need a replacement

... Euro-Pro EP923 Canister Steam Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the

... Dirt Devil M088905 Vision Bagless Upright Vacuum

The small belt that makes the beater bars spin broke. It is only two years old; repair shops tell me this involves replacing two belts because of some kind of clutch to the tune of $150! Is this possible to repair myself

A very easy replacement. The belts cost about £3 each. Yes, there are two belts and even if the clutch needed replacement, this is about £20 for clutch and both belts http://www.dysonpartsdirect.co.uk/dysonparts/dc07belts.shtml - this is ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

Lawnmower I have a black and decker hovermaster lawn mower. While mowing my lawn I went over a small stone. It doesn't seem to have damaged the blade but the engine instantly cut out and I am unable to start it again, I have replaced the fuse which has made no difference, Can you suggest anything please.

There may be a thermal fuse fitted to the motor, sometimes they reset when they cool down. Sometimes they are a one shot fuse, when they blow the have to be replaced.There may also be a reset switch on or inside the operating lever/switch. ... Vacuums

Problem with small belt and beater bar spinning. Where to get replacement belt and what is it called model number. Thanks. Only 2 months old 5780-900 Hoover windtunnel cyclonic

Here you can get a package of the belts you need. Also here is a link to the manual:U5780-900 Belts\015\012\015\012\01 ... Vacuums

Dyson DC07 bin trapdoor won't stay closed: The small plastic piece on the tip of the center rod on the cylone assembly broke off, so my trap door won't stay closed. Any idea how to find just that part, so I don't have to replace the entire cylone part?

You can buy that part here: Dyson DC07 Spares ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?

Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

On our Hoover U6445-900 (Mach 6.9) we replaced the small belt that goes to beater brushes in front of unit. Upon starting, the Hoover quickly got hot and smoky. We shut it off and looked things over carefully, but the second try also resulted in friction heat on the belt. Now it appears the belt may have stretched due to heat and the brushes won't spin. Any ideas?

Are you sure you purchased the right size belt..the friction you speak of is usually caused by a belt not being the right tightness or a jammed beater brush ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Replacing filter Got a Filter Queen Majestic vacuum from my inlaws when they moved overseas. I am in middle of vacuuming, got a weird noise, so opted to check and clean the filter for first time. UGH. The lower 'pot' that's the bottom part of the thing was full of gunk, but the filter pristine clean against the cone that's attached to the upper part of the unit. In other words, I am shocked to see that the dirt goes not INTO the filter, but outside of it into the bottom portion (that I call the

Its normal operation so don't worry ... Filter Queen Majestic Canister Vacuum

I have had my Bissell Healthy Home for just over a year. I use it once or twice a week on five area rugs and two small bedrooms with wall to wall carpet. Just recently, the motor started to sound extremely loud and it smells like it's burning. The vacuum still picks up everything and all the brushes are turning. Advice? I really like this vacuum and would really like to fix it rather than replace it!

Hi,Here is a tip that I wrote about my Bissel but I bet you have the same problem and the hose is clogged...Bissell Bagless Upright Vacuum no ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

For a Bissell Pet Hair Eraser the drive belt recommended is a size 8... is this right? It seems VERY small and difficult to replace.

No it does not use the style 8 belt. It uses the style 7/9/10/12/14/16 belt. You can view the manual and buy the belt here:http://www.vacbe ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Help please. I have small silver cylynder vacuum with retractable cable paper bag. i need replacement bags. Durabrand 1300

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=632941\015\012Generic problem for all Vacuums\015\012Help please. I have small silver\015\012Posted by ... Vacuums

I have a Beam Rugmaster Plus power head Model BM1 393 Type AB and the connection were the metal pipe meets the plastic swivel broke close to the unit. It appears like a manufacture defect in that is broke in two small places and not the entire unit. Can this piece be replaced or glued??

This is most likely repairable. Lots of the Beam parts are available. I would recommend checking out any local vacuum shop or searching online for a central vacuum store that sells beam products. ... Beam Industries 750 Classic Bagless Central System Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0475 seconds