Having problems with your Vacuums ?

I have a raynor flight star garage opener. Had a lighting strike 4 days ago. All power is good. The opener even has a little green light on the switch that is attached to it. However the opener is not responding. Is there a way to reset on the motor by taking off the housing? I don't see any reset button on the out side of the housing.thnx w


Answers :

You could always try unplugging the unit and plugging it back in. If that doesn't work the logic board is probably fried and unfortunately there is no replacement available for it any longer. You would need to buy a new opener. I'd recommend Liftmaster.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a raynor flight star garage opener. Had a lighting strike 4 days ago. All power is good. The opener even has a little green light on the switch that is attached to it. However the opener is not responding. Is there a way to reset on the motor by taking off the housing? I don't see any reset button on the out side of the housing.thnx w


You could always try unplugging the unit and plugging it back in. If that doesn't work the logic board is probably fried and unfortunately there is no replacement available for it any longer. You would need to buy a new opener. I'd recommend Liftm ... Vacuums

I have a Liftmaster garage door opener and the garage door faces south. Normally the opener works great except at certain times on a sunny day.The sunlight is not directly hitting one of the sensors but the door will comedown as far as half way and then it will go back up and the lights will flash. If I go inside and use the button I can hold it down until the door is fully closed. However, sure is a pain to have to take the car out, go back into the garage, shut the door and then leave the h


Sounds like a problem with a limit switch or something getting in the way of the electric eye that interrupts for safety reasons. \015\012Clean the electric eye transmitter and sensor of debris and cobwebs and make sure the wires are attached properl ... Vacuums

I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.


I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Hi there. My coromaster 2000 has lost its limits. The travel on the opening mechanism is about 100mm each way i.e. the limits for opening and closed position have to be reset. How is this done. On back of motor there is a micro switch which has to be pressed to set limits. What is the sequence of pressing and activating. Thanks a ton I really look forward to hearing from you Cheers Graham


... Vacuums

I shorted out the light socket on my Chamberlain Professional Garage Door opener. Now it wont open, I am looking for a fuse or reset button, but cant find one. Is there a way to reset it or did I fry the solinoid


First check your house fuse. ... Vacuums

I have Pro Safe PSF80 and everytime I enter my password, the lights are blinking and can't open the safe. Since the only way to reset my password is when the door opens, I cna't reset it either. I need yuor help, how to fix this problem.


2 blows with a pickaxe on the hinge and it was open in less than 1 minute ... Vacuums

My Nilfisk GWD 300s had been working fine, however today i could smell something like burning smoke from the motor, when i opened up the motor i could see a carbon metal rod touching the motor shaft a


... Nilfisk Vacuums

I opened the cannister to change the bag and when I closed it the motor switch will not turn on. The second position which turns on the attachment for rugs still comes on. We thougth it was the switch so we ordered the part and it is still doing the same thing. Is there a reset button somewhere inside? The only reset button I see is on the attachment which is working.


It can be a few things. First check the overload protector located on top of the canister. If it has tripped the unit will not run. Push it in to reset. \015\012If that is the problem check the motor safety filter to see if it is clogged and caused t ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.


... Electrolux Vacuums

The thermal motor protector on sears model 116.35912 Kenmore vacuum won't reset. The manual says to wait 30 minutes and the thermal protector will reset on it's own. It appears I would have to take the vacuum apart to get to the thermal protector. Is it worth the effort or should I trash the vacuum?


... Kenmore Vacuums

My Dyson Ball rug attachment won't work - something had caught that I cleared, but the reset button does not reset the vacuum. This happened once before and I had to take it in. Is there another way to fix this simple problem?


... Dyson Vacuums

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together


... Vacuums

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis


Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums

My filter queen just had the motor rebuilt last year and was basically a brand new unit when I got it back. It is not picking anything up now when I vacuum. The beater bar on the carpet attachment is turning fine and when I take all the attachments off the hose I can feel the suction being created like it should be picking up debris just fine. I have emptied the canister even when it did not have much in it; however, it still will not pick anything up off the carpet. It picks up debris tempo


It sounds as if you have a clog inside the "Power Nozzel". They mention that there are "no user serviceable parts within the Majestic® Power Nozzle" My advice would be to see if you can see a clog with in reachable distance and try to remove the ... Filter Queen Vacuums

I have just purchased two (2) Electrolux Nimble vacuum cleaners. Not one, but both, straight out of the box, the beater bars will not run. It turns on, select carpet, and lower the handle, the red light to check beater bar/or filter lights up. You can reset the light by unplugging the unit, then plugging it back in, but with same results. Now the kicker, if you take out the handle, select carpet, lower the body by the carry handle, it will run and operate correctly, however, as soon as you r


... Vacuums

I have a Royal 7910 extractor and even though I vacuum before cleaning the carpet, by black cocker spaniel's hair gets pulled into the plastic pick-up attachment and I cannot find an easy way to clean it out. I have tried taking the screws out to separate the halves, but it seems as though they might be glues together. I have run water from a sink sprayer though the openings with some degree of success, but it still is pretty cruddy. I have tried snaking pipe smokers pipe cleaners up the pick


One person wrote this in a review:\015\012Most home carpet extractors are very difficult to take apart for cleaning and maintenance. The Royal 7910 is the exception. No tools are needed to take the front housing off to clean out all the pet hai ... Royal CE7910 Wet/Dry Vacuum

Hello i own the bissle proheat steamer it turns on but no water or soap or suction from floor or the utensiles ive taken the take off the back to scope out anything that could be in the way but dont see anything the motor is making that clogged vacume noise witch makes me believe something could be stuck somewhere in it but it could also be no water is getting to the pump or despencer but the brissels still work belt for that is good where would i be best to check and where is the location of th


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I'm trying to change the filter....One person told me to open the hose end and take the bag out and go from there, but that isn't the right way!!! It's the other end where a couple brushes are able to be stored on top of the canister, but I can't figure out how to get that section off..it's as tight as a drum HELP PLEASE and thanks. Betty


There's a tab at the middle of the lower back of the tool holder (air diffuser). Pressing in on that tab should enable you to lift the back of the holder first, then lift off the whole thing. It will come off, just make sure the tab is in far enoug ... Electrolux Epic 6500 Vacuum

My miele S277i will not start up The fuse is ok in plug etc Wire not broken anywhere When I opened it up I found that Power is getting all the way to the motor brushes in fact. Any ideas?? Regards Andy


Hi, \015\012\015\012Usually when a Miele doesn't start it's one of several things. Most commonly the cause is a faulty cord reel, however if you get power all the way to the motor brushes, it sounds as if you cord reel is ok, and that an ... Miele Vacuums

My Kenmore 7520 canister vacuum has a problem with the retractable cord. It has jammed and does not come out or retract. It jammed half way through the retracting action. Cannot pull it out or retract. Would like to know how to open the canister to take a look for the problem. Thank you


... Vacuums

I have a Sleeptight Imetec Electric Blanket with timer and Dual Controls one for each side of the bed recently the timer was set for 45 minutes and when 45 mins elasped it went off and the control light began to flash which is normal however it is since stuck in this mode light flashing will not heat just keeps flashing is there any way of sorting this the other side of the blanket for the other side of the bed seems to be ok although it did the same thing but reset itself any ideas Regards


... Vacuums

Dyson DC23 Vacuum shut off and came on. Thought it was a problem at the electrical outlet as when moving plug it would come on again. Seen canister was full, emptied it and cyclone was quite plugged up so poked out the dirt. Had dog hairs in it as well as some ashes I had just vacuumed. Plugged unit in again and pressed switch. Will not come on. Tried another outlet. Is there a reset button somewhere or could the ashes have seized the motor. What can I try besides taking it to a repair sho


... Dyson DC23 Bagless Canister Cyclonic Vacuum

I have a Eureka Boss Model 411... I need to know where the reset button is for the suction motor. The canister was clogged on the backside, I didn't see it and the suction motor shut off. I have cleared the obstruction, but don't know where the reset is for that motor. I know how to reset the brush head motor.


If your vacuum motor overheats, it will stop working. it will start working again once it cools. ... Eureka 411A Upright Vacuum

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse


By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

My tank foamed up into the motor and now the rainbow won't come on. Is there a reset button for the motor somewhere? Will it dry out and reset on its own?


Reset switches are generally for use after a motor has shut off due to overheating. They don't do any good for resetting a motor that has gotten moisture into it. Moisture in a motor will quickly ruin it. Allowing it to dry out on it's own will ju ... Rainbow E series Canister Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0586 seconds