Having problems with your Vacuums ?

I have a samsung SC7800 (smart wing system) vacuum cleaner. I think the impeller is jamed with sawdust. I have removed the part than holds the removable filter, but can't see how to remove the reat of the top case to access to impeller housing. Does anyone know how to do this or where I can view a repair manual for this model?


Answers :

Unfortunately these tend to break frequently.... You might be able to get a wiring diagram at www.wize.com Good Luck!!
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a samsung SC7800 (smart wing system) vacuum cleaner. I think the impeller is jamed with sawdust. I have removed the part than holds the removable filter, but can't see how to remove the reat of the top case to access to impeller housing. Does anyone know how to do this or where I can view a repair manual for this model?


Unfortunately these tend to break frequently.... You might be able to get a wiring diagram at www.wize.com Good Luck!! ... Vacuums

My DC 17 is plugged. I can see through the small hole in the top blue "flower shaped" that the holes at the top of the canister are plugged with hair & dirt. I cannot see anyway to get to these small round holes. Is there a way to remove the top blue "flower shaped" piece? I have removed the inner cone from the clear canister but still cannot get up underneath.


Please kindly follow the steps below to clean your vaccum cleaner,1.) Remove the clear plastic handle. You\015\012will have to take out two screws and then unclip from the from the\015\012front. It's stiff, I gently used a flat head screw drive ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.


The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I need to remove the top cover from a Wertheim w4030, I have removed all screws that I can get at. I have notice a further 3 in places that is not possible to access. It looks as though the two buttons on the top if removed will provide the solution but I don't want to break anything by forcing something that is not supposed to be done. Can you help?


... Vacuums

Upright bagged vac model U1550: how to access hose housing to remove blockage?


... Electrolux Vacuums

I need to change the retractable cord in a Kenmore Model 116.228.13204 vaccum but can't figure out how to remove the housing. I have removed the bag and the two screws but the top appears to be attached under the foot pedal. How do you release it. Does the foot release pop off somehow to reveal another screw in the back of the housing?


Go to this web site, it gives you complete schematics of your model. This will make it easier to see where all screws are and what you have to remove to get to reel. http://www.searspartsdirect.com/partsdirect Just enter your model # and complete bre ... Kenmore Vacuums

Unable to remove round filter in bottom due to bolt not secure inside vacuum and it is just spinning so I can't remove nut holding on filter, but cannot see how to remove top of vacuum to get at other end of nut.


If you are talking about the acorn nut that secures the separator to the motor shaft, it can be removed with a small (or even a big, for that matter) air or electric impact wrench with the proper sized socket. Find a mechanic friend who has one, make ... Rainbow E series Canister Wet/Dry Vacuum

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?


... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

How to open main case on a dc08. i have removed the two screws under the top filter but i can not figure out how to seperate the main case so i can replace main switch. any help would be much appreciated


... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help


Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

Where can I find a part for my BV2000 in house vac? It is the smallest unit made by M S & S Systems in Dallas TX. The suction impeller is grinding in it's housing, so I need a motor/suction pump. I have removed this combination from inside the vac assembly


You will have to replace the whole motor as these motors where never made to be serviceable. if you take the motor to a local vacuum shop than can order you a new one. though i would recomend replacing the whole tank unit with a Nutone or Hayden they ... M&S Systems BV-2000 Bagged Canister Vacuum

I need to change a belt and cant remove the casing as carpet adjust is attached and cant see how the red knob is removed


... VAX Appliances Vax X3 Bagless Upright Vacuum

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

Dyson DC 14 hose has no suction, with or without brush attachments. Hot air shoots out from the base of the canister when I try to use the hose. I cleaned the top filter, but can't figure out how to remove the hepa filter to clean it without destroying the case. It looks like it might take three hands to insert pennies and "flip" the case open as is suggested on a youtube video for a different model. Would this even help, assuming I could get the thing open?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Change belt How do I change the belt Eureka whirlwind 4480. As I look under the house I think I see one screw on each side down in about 3/4 inch. Are those the screws to remove and are there only two you have to remove?


... Eureka WhirlWind 4381 Upright Vacuum

Mystery part Bissell 1699-P. I removed the top cover and a part came tumbling out (from the rear of the machine - towards the handle area). I have no idea were this part belongs. I have a schematic of the cleaner but I can not locate the part on it. I tried to copy and paste a picture of the part but that isn't working so I will attempt to discribe the part: There is nothing stampted on the part that I can see. It is plastic(white), 2" long, 3/16" in diamater. One end is U shaped (u-shape is 1/4


One question... you haven't mentioned that the vacuum doesn't work now... as hard as this is to accept... if it doesn't effect the function... forget about it.... i could very well have been something you vacuumed up along the way.\015\012 ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Have a 6 year old pocket cigarette lighter by DAX (snap top and jet flame). Fills with butane and I can see a spark looking down into hole where grill is housed -- but it doesn't light. Can I repair it or do you know where I can send it for repair? Bill Plauth, MD, Santa Fe, NM


... Vacuums

Motor sounds loud and high pitched. Suction seem ok, can't find any blockages. Cleaned filter at top of removable canister. Exhaust seems hot and low. Can there be a blockage within the motor housing?


Most likely your bearings are shot. it will need a new motor ... Kenmore Vacuums

Cant remove top on vax power pet 2 to get access to belt


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

My Fantom Thunder upright has a blockage that sounds like it is directly above the dirt bin in the "head". I cannot access it from inside the bin chamber by going up the nozzle with a claw parts retriever. (This is the older model where the cyclone nozzle doesn't come off.) The wand, hose, rear inspection port, and front brush intake are all clear. How do I get the top of the vac off above the dirt bin? I don't see any screws or slots.


... LG Vacuums

I need to open up this Hoover Uprite Runabout deluxe to replace the belt. I dont see any screws to remove to access. Model # U5064-940


You will find them on the bottom of the machine on the brush roll cover. This is the belt you need:Hoover Runabout Deluxe U5064-940 Belt ... Vacuums

I need to remove the top of the motor unit on a Kirby Generation 3 to access the motor area of the vacuum


First remove the back, then remove the handle assembly. Then pop off the plastic switch cover and it has one screw on the back you will need to take out, then there are two screws in the front of the body housing and two on the back that you will ne ... Kirby Generation 3 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0393 seconds