Having problems with your Vacuums ?
When I turn on my magic mic and set the tv to video 3 it is scratchy but the sound is there. How to solve this problem?
Hi you can troubleshoot the cable your using for connections and after troubleshooting cables,you can also check the TV input plug in port if it is working well,
I think that will do.
I think that will do.
Either the mic has a bad solder or wire connection inside it, or it has a power supply, amplifier, or transmission problem. The unit is going to have to be taken apart, and troubleshot. Make sure it works the same way on another set, just to make sure the set's not off-frequency, etc. Once you know the mic's the problem, you will have to open it up and see what you can see. This could be a capacitor in the power supply circuit going bad, but not likely- most likely will be a cracked solder trace or wire. Inspect it with a magnifier- cracked solder joints are hard to spot with the naked eye, often times. Also, a switch could be going bad- they're always to be suspected. Haven't heard of this problem, so that's all I can offer about it. Good luck, and hope this helps.
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
When I turn on my magic mic and set the tv to video 3 it is scratchy but the sound is there. How to solve this problem?
Hi you can troubleshoot the cable your using for connections and after troubleshooting cables,you can also check the TV input plug in port if it is working well,I think that will do.Take care. ... Vacuums
Dirt finder I have a Hoover U6439-900. After the cleaner was used a few times, the dirt finder light cycles between green and red on the regular setting and will not go to green. On the sensitive setting, the red light stays on most of the time. I have tried to run the cleaner to remove any dirt but have not solved the problem.
The sensor may be bad, or it may be coated over with dirt. Re,ove the hose at the back of the vacuum, the head of the sensor is down inside that opening, reach in there and clean it off and see it that corrects the problem, if not replace the sensor ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Floormate Spinbrush The water comes out fine to clean but when I out it on the wet pickup setting, it piskc up in streaks and it has the most horrible sound while moving it around, like the rubber is going across the floor dry. Any solutions or anyone with similiar problems and a fix?
Not sure if this will help but these machines are ment to be used in one direction not back and forth like a vacuum cleaner. You should start in one spot and pull towards you slowly with the trigger depressed it is designed ... Hoover Floormate H3000 Upright Wet/Dry Vacuum
I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara
I have owned my kirby sentria for 2.5 years and have had no problems until now. The vacuum still works but I cannot lower it all the way down or the light will turn off and it will start to smell like something is burning inside. I use it on the 2nd or 3rd setting with no problem. I have changed the belt and cleaned all the hair and strings that were on the roller but it still has this problem.
Kirby has a 3 yr back to base guarentee so contact ur local rep or kirby direct and thy will sort it all from there, hope this helps :) ... Kirby Vacuums
Horrible sounds on carpet setting!
Sounds like what ours is doing. we took off the roller, and if you look on one side, it's melted. we're looking at either replacing the roller and seeing if that helps...and hoping it doesn't happen again...or we may just go out and replace the vac ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum
I am trying to install a train air horn. i bought a viair compressor for it. the horns themselves have a 12 volt hookup going to what i believe is acting like a solenoid. when charged, you complete the circuit and walah, the horn blasts. the problem im having is when the compressor is building pressure, the air horn is automatically putting out a dull sound, getting louder as the pressure gets more and more. it sounds like its out of one horn however. it is doing that without the 12 v hookup. is
Hi! just a tip regarding the sound that comes up when building pressure. Is there a gasket or rubber seal on the horn? You may need to replace this for it may be worn. The air may be coming out of the worn seals resulting to sound even when not trigg ... Vacuums
I have a Dyson DC17. Everthing appears to be working but when I set it in motion I hear a loud screeching sound. Sounds like a belt on the brush roll cover but the roller still spins.
The belt might be worn and causing the sound. Here is the belt you need and the manual:Dyson DC17 Belt and Manual ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have a Filter Queen Majestic 360 and am having problems with the powerhead. There is a loud rattling noise in the powerhead, especially when I vacuum thicker carpet. I have replaced the motor, roller brush, and belt, but the rattling remains. It sounds like it is coming from the roller brush area,and when I turn the powerhead over, it rolls free and sounds fine. Any thoughts?
Hi there, as per your information i guess its a problem of power transformer. He can't supply the proper power in the motor & thats why the noise will come from the transformer. Thanks & waiting for your feedback. ... Filter Queen Majestic Canister Vacuum
There is no suction from the sweeper head but plenty from the wand. I have viewed several videos and visited seveal dyson web pages and none address this problem. I have thoroughly checked for blockage per video instructions. There were NO BLOCKAGES. Please help. Thanks Doug
Hi Doug,\015\012\015\012There are several things that this could be. Probably the most common problem that we see when customers come in with this problem is actually a fairly simple problem to fix. Here are just a few things that this co ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
My vaccuum makes a very high pitched sound when it runs. I cleaned it out and checked for itms stuck in it but there doesn't appear to be anything. What is causing this problem. Other than the awful sound it seems to be working fine.
Could be a worn belt. Here is the belt you need:Bissell Pet Hair Eraser Belt ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum
Nothing happens on the "bare floor" setting, it does something on the carpet setting but definitely not the normal sound or suction.
The switch frequently go bad on those. p# h-59136035 ... Hoover S2220 Flair Bagless Upright Vacuum
I have a PQ1500S Brother Quilting/Sewing machine..I am having problems regulating the tension, what should it be set at normally??? I keep having problems with repeated thread breakage, and its a new machine. I have followed all information in the manual. Thanks Theresac57
Hi I need help because I have a problem with my Electrolux Centralux Central Vac system in my house. When I plug the vac hose in the central vac socket at first I heard the motor running very gently with NO suction then after a minute or so it went completely dead and they is NO motor sound, suction, or anything happening what so ever. Can anyone tell me what this problem is???
Have you checked for a clog in the lines or in the hose? If there is no clog in the system anywhere, then your motor could be dying. ... Electrolux Centralux Vacuum
My Bissell Pet Eraser brush only rotating on the bare floor setting, when on the pet setting, it won't rotate. What is the problem? Thanks.
It sounds like something is backwards. the brush should only rotate when using it on carpet, it should never rotate on the bare floors. check the belt for propper installation ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum
I noticed the Roomba's brushes were not sweeping, or turning so they could sweep. There was a new sound coming from the machine, the sound of grinding nylon! Upon inspection, I determined the problem to be a heat melted gear support hole. The hole was no longer round but oblong. You could see a ridge of plastic around this hole. So melting I believe was the culprit. The gear that uses that hole was then able to tilt to one side, thereby allowing the gear to disengage from the drive train. I
Be sure to keep your brush bearings clean. If they get clogged, the brushes don't turn and the drive sockets can get damaged. ... Vacuums
Over heating? My 10 gallon 4HP shop vac has started shutting off after about 30 sec. after I turn it on to use. It smells real hot after I shut it off. I have changed the filter and the bag, which did not solve the problem. Any suggestions on what the problem could be? It's only about 31/2 years old and I really don't use it all that much, mainly for getting up dust and cob-webs from my garage.
It sounds like you need to replace the motor in it . thank you for using fixya ... Shop Vac ShopVac 3 HP 2 Stage 10 Gallon--Automotive Wet/Dry Vacuum Vacuum
There is no problem you have solved the problem and this is to say thank you so very much. Shirley messina
You are so very welcome. thanks for getting back to us. ... Vacuums
How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a
The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Cleaning problem When i clean after is dry looks ashy, what i need to do to solve this problem
Hi,This type of problem usually is not he fault of the Shark Steam Mop.The problem is the old residue left on the floors by other cleaners.Here is a tip that I wrote that will help you out with that problem... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
I recently purchased this vacuum after reading consumer reports article on it and from recommendations from family. However, since I've had this vacuum it's been nothing but problems! I have a frieze carpet and I have the vacuum set on the highest setting. Each time I use it, the vacuum clogs with carpet fibers before I even finish a room! Any suggestions?
Is that a shag carpet? the power head is raised up all the way can you lower the suction on it is the carpet old the vacuum may not be able to handle the carpet,go to a vacuum store and see if you can try somthing else out some stores well let you re ... Hoover Tempo Widepath Upright Vacuum - Blue
Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi
Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum
Roomba Stops I've had a Roomba for about 2 months. Lately, it runs for about 45 secs, then stops, makes a two-tone (descending) sound, and flashes the CLEAN button while the STATUS button is red. I've emptied the dustbin on it. Can you help? I am seeing the same problem on my roomba today. I cleaned all that I could., the brushes, the pins on the sides and all that and it still gives the same problem..Any other fix?
Run your roomba through a self diagnostic test. I have posted the link below. Tell me your findings.\015\012\015\012\015\012http://mysite.verizon.net/gsplews/Diagnositic-Tests_Proc.v.0.5.htm ... iRobot Roomba 4210 Bagless Robotic Vacuum
I have an older Oreck XL vacuum that sounds like it is running twice as fast as it should. I disassembled the entire vacuum, including disconnecting the motor wires, to clean out the hair, string, and other things. When I put everything back and connected all the wires, everything appears to work, including the light. The only problem is, it sounds extremely loud like the motor is running too fast. The model number is: XL3610HH Ser. No. 3610HHXA039740-6 I do not have as electrical diagram to see
... Oreck XL Ultra Bagged Upright Vacuum