Having problems with your Vacuums ?

Fixing my vacuum cleaner

\015 I've had a Eureka Optima lightweight upright for 7 months. One day while vacuuming the carpet in the living room, the motor started making a grinding sound. I thought something was caught in the rollers. After cleaning the small amount of fibers from the rollers, the sound continued. I have no suction. What could have happened?I have only two floors that are carpeted in my apartment.I don't use the vacuum cleaning alot. Please send my some information that could save my vacuum cleaner.\015

Answers :

Check to make sure that your agitator still spins. (Agitator = brush). If your agitator still spins, it eliminates your belt and agitator as likely culprits. The last possible solution would be that your vacuum is clogged. The grinding sound might be a motor-related issue or could possibly mean your bearings are going out. Check the bearings of the agitator and the motor of the vacuum.
\015\012
\015\012Accessing to the agitator and belt can be done by removing the bottom cover of your vacuum. There are 2 scews that are holding the bottom cover to the head of the unit. Remove these 2 scews and the bottom cover should snap off.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My hoover Wind Tunnel vacuum cleaner's motor spindle keeps overheating. Because of the high temperature, it keeps burning through belts (the big, wide ones). I have taken it in to the vacuum repair shop about three times now, and the problem has never been fixed. Does anyone have any advice on how to fix this or should I just buy a new vacuum?


... Vacuums

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

Fixing my vacuum cleaner


Check to make sure that your agitator still spins. (Agitator = brush). If your agitator still spins, it eliminates your belt and agitator as likely culprits. The last possible solution would be that your vacuum is clogged. The grinding sound might be ... Vacuums

Electrolux Z61 Handheld Vacuum Cleaner. Brush heads have stopped turning. Have removed screws but the casing seems to be still fixed together by a plastic joint which looks as if it will break if forced. How can I check that the belt is OK, and if it isn't, how do I open the cleaner to replace it?


... Electrolux EUK71B Bagless Handheld Vacuum

I have a Wertheim 4808 Barrel vacuum cleaner that has suddenly stopped working. I believe that there is a problem with the electrical cord connection inside. I have tried unsuccessfully to open the compartment that leads to that area. One side unscrewed with a phillips head screwdriver but the other side seems to have a different type of fixing screw that I am unable to undo. It is awkward to get at and in a deep slot and the head of the fixing screw? is not visible.


... Vacuums

My Kenmore canister vacuum cleaner model 116.27514700 has unacceptably low suction.It is much less than my older GE Walmart canister vacuum. the 2 filters are very clean and there is no blockage in the hose and the dust collection bag is empty. Is poor suction a characteristic of this model or if not is there a way to fix this problem?


... Panasonic Kenmore Canister Vacuum Vacuum

Hi, I have a Miele s247i vacuume cleaner- My electric coard does not roll back, How do I open the vacuume lid / housing to fix or replace the spring? do you have instruction manual on how to open the cover?


... Vacuums

How do you fix a hoover z114 model vacuum? - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


What seems to be not working on it whats it not doing ????not trying to be smart or anything but please describe the problem your haveing with it ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How to fix my rainbow vacuum cleaner - Rainbow E series Canister Wet/Dry Vacuum


We need more information on what the problem is. Give us a call and speak to a Rainbow Specialist. We have pickup service at your home the next business day at not charge.RainVac ... Rainbow E series Canister Wet/Dry Vacuum

How to fix bissell deep cleaner water pump - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Fantom thunder vacuum cleaner how to fix problems


... Vacuums

How to fix Dirt Sensor on Panasonic vacuum cleaner


... Panasonic Mc-ul915 Bagless Upright Vacuum

Power Issue Hi...my Miele vacuum cleaner (S314) will not turn on, unless I lean it on its side (the side that the power switch is on). I took it apart and the wires are all well attached, and I do not see any issues with the connectors. Is this a common problem with an easy fix? Thanks! Todd


Could be the cord reel causing the problem. Sometimes the contacks on the inside of the reel loose contact and won't conduct. If this is the problem, then you will have to replace the reel cord asm. Part # 06777540, may cost about $150 approx. ... Vacuums

I have a Filter Queen Majestic canister vacuum cleaner. At the end of the wand, a button to release the attachement not only broke, but also one eyehole on the wand where one nipple on the button falls into. So therefore a new button isn't going to fix the wand because there isn't a hole on one side of the area where the button falls in place for a nipple to secure the button in place. IS THERE A REPLACEMENT PART FOR A NEW SECTION OF THE WAND WHERE THE RELEASE BUTTON IS SECURED IN PLACE THAT I C


... Filter Queen Majestic Canister Vacuum

How to fix or change a bissel vacuum cleaner power switch for model E6594


... Bissell 6594 PowerForce Bagless Upright Vacuum

NO SUCTION My Electrolux Z2274 upright vacuum cleaner has lost it's suction and is very noisy. Have checked and rechecked there is no blockage. Have cleaned the filters. In fact done everything I can think of. Any one know why and how to fix this??


If you have no suction, there are only a couple of things that could cause it. As you have checked for blockage, and changed your filters, you may have a vacuum motor with bad bearings, or broken fan blades (inside/on the vacuum motor). Either sympto ... Electrolux Central Vacuum

I have a Kenmore Vacuum cleaner 116.24212. The retractable electric cord won't retract. How can I fix it?


... Kenmore Vacuums

My rainbow e-series canister vacuum cleaner has a horrible smell. i cleaned out the water tray and it STILL smells horrible. how do i fix this problem?


Get a new hepa filter.\012\012It is at the back side of it, behind that rectangular cover, where the exhaust cover is. It either snaps off with two plastic tabs on the bottom of it, or has two screws on the bottom of it, and two screws be ... Rainbow E series Canister Wet/Dry Vacuum

The vacuum cleaner stopped working.. It will not run. How do I fixs it? A new bag is on it.


... Simplicity 7850 Premier Bagged Canister Vacuum

I have euro-pro 1200w vacuum cleaner. I doesn't switch on . Could you pls. help me to fix it. Thanks Ejaz


... Vacuums

How to fix a vacuum cleaner ...its very loud and has no suction


You need to replace your vacuum belt. you can get replacement belts here:Replacement Vacuum Belts ... Vacuums

Trying to fix new belt to Hoover Turbo Power vacuum cleaner. Don't see how the belt becomes taut. Fitting it around the roller, there is nowhere to fit the belt to, it just sits loose.


I looked at the user instructions guide online and saw where the 'other end' of the belt should be fitted. It was extremely hard to fit but eventually managed it. Thanks for this solution site. I wouldn't hesitate to use it again. ... Hoover U5396-900 Turbo Power Vacuum

I have a Miele S5980 vacuum cleaner, and recently had to change the Hepa filter. After doing the change, I tried resetting the reset button to switch off the Hepa filter indication light and it would not switch off. After a few tries, I accidentally depressed the switch, and it has dislodged from its cradle. Help, what can I do to fix this?


... Miele Vacuums

Vorwerk VK121 vacuum cleaner - smell of burning from housing enclosing motor. How do I get into the housing to inspect the motor? After tilting the bag sideways, there are two screws holding the housing visible, but there seems to be a thrid fixing inside the point where the handle shaft is attached - is the handle simply clipped in place? Thanks


Yes the handle is clipped in place and should come out when the button in front is pushed. Remove the screws you wrote about. After that the puzzle begins. At the bottom of the vacuum where the head is attached, remove the head by pressing the but ... Vacuums

Eureka Uno upright vacuum cleaner, 2940-2969 series. How the heck do you use the attachments? If I fix an attachment to the end of the hose all this dust spews out of the tube...


... Eureka Uno 2998AZ Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1011 seconds