Having problems with your Vacuums ?

Sebo X1 vacuum not working

\015 Sebo X1 upright vacuum. Problem - height adjust is not working, staying in highest position. Is it worth trying to fix?\015

Answers :

The X1 has a servo motor with gear box, this is what adjusts for height. Either something has jammed it, or
\015\012 it has gone bad. You would probably be looking at a $80 to $100 repair, that is if the servo is bad. There also is a computer controller circuit board which could be the problem.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sebo X1 vacuum not working


The X1 has a servo motor with gear box, this is what adjusts for height. Either something has jammed it, or \015\012 it has gone bad. You would probably be looking at a $80 to $100 repair, that is if the servo is bad. There also is a comput ... Vacuums

SEBO vacuum cleaner makes a strange noise and shuts itself off after a few minutes. Suction not working when tube is attached, but works with hand-held portion only. Indicator light saying bag is full/clogged is on, but we've cleaned out the bag, cut away any fur/strings that were wrapped on the turning portion, and cleaned out the refuse valve. Not sure what else to do. Thanks!


... Sebo Vacuums

Sebo upright. Check brush light come on when in use. Vacuum appears to be working ok but seems a little heavy.


Try adjusting the height up ( higher the better ) also make sure the brush is turnig freely if not remove it ( push the button on the top of the brush roll housing and pull the side off ) and make sure nothing is stuck ... Vacuums

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.


Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

I have a kenmore progressive direct drive handi mate jr. upright vacuum. My daughter used it last night to vacuum up some cat litter that had spilled on the floor. I went to use it today and it turned on for a second and then stopped working. I have hit the reset button but it will not turn on. Help this vacuum is only 2 years old Is there anything that I need to reset or do so that the vacuum will work again?


Its probably clogged up with cat litter.might have gotten into the motor.your motor has a motor guard inside if it. when it overheats it will shut down till it cools off.you need to clean all th cat liter out of it.and clean the filters.with a direct ... Kenmore Vacuums

Sebo Automatic X1 vacuum cleaner doesn't produce much suction.


If the motor really is working, the problem is most likely to be that there's a blockage somewhere, and on this excellent vacuum cleaner there aren't too many places to look. You've probably already looked in the inspection flap on the underside. If ... Sebo Automatic X1 Bagged Upright Vacuum

MC-V7400D Vacuum Vacuum will no longer create a vacuum Changed filter and still does not work. Sounds as if it is working.


Blow in hose and see if it's clogged, possibly a belt is come off. ... Vacuums

I was vacuuming and my electrolux 2100 accidentally suctioned the string attached to a balloon. I turned off the vacuum and unwrapped the string from the head of my vacuum. On the hose i have plenty of suction but the head isn't working. i flipped on and off the emergency shutoff switch but it is not working. what happened? what can i do?


... Electrolux UltraLux 2000 Bagged Canister Vacuum

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.


When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I have a miele S4210 vacuum. It has a SAB100 accu nova battery brush which will not work. After charging the battery, light comes on saying not charged and now the power head brush won't turn. I had problems with my first powerhead so I purchased another and it worked for a short time and now I have the same problem again. I have four batteries I use interchangeably but nothing seems to work. I spent a fortune on this vacuum and to tell you the truth I hate it! Contacted Miele after 1st year of


... Miele S300 Bagged Canister Vacuum

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!


Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum

Motor works. brush and vacuum does not work - Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum


Probably a broken belt. don't worry, they are very cheap at a vacuum store$2.if it still does not **** then maybe it is clogged or hose is disconnected ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum

I have a Craftsman wet dry vac with blower capability (22 L). While I was using it to **** up water, the water came out of the blower hose. Now I can't get it to work as a vacuum. What can I do to fix this problem? Is there a toggle switch somewhere that allows me to choose vacuum or blower? Also, will the vacuum still work without the filter nut attached to the plate? Please let me know at your earliest convenience. Thank you.


... Craftsman Vacuums

I have Hoover WindTunnel Air Upright Vacuum - UH70400 just used couple of times. While vacuuming the carpet carpet fringes were rolled up in to brushroll and brushrol stopped working. It means vacuum is not working effectively now. Brushroll indicator is flickering.


... Hoover Vacuums

Hand held attachment works, floor vacuum works...carpet vacuum does NOT work.


That means that you need to replace the belt. Here is the belt you need and the manual which has instructions:Dyson DC07 Belt and Manual ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a DC 17. In the middle of vacuuming the vacuum stopped working when it was in the upright position. It only works when the head is down and i am using the bar. I can not use the extension bar, becasue when I put the vacuum upright it shuts off. Where is the problem?


Hi there, it's Jack at Dyson.\012 \012 Like most Dyson vacuums, DC17's main suction motor is protected by a thermostat which shuts the machine down if it starts to overheat. This could be due to a blockage, and the filter may also need a wash ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Why doesnt my Dyson auto adjust on our carpet? We have a taller, soft carpet and it digs into it, making it very difficult to vacuum. We have had the vacuum for about a year at another house and it worked GREAT on the berber......our new has a tall carpet somewhat like shaved berber and now the vacuum wont work.


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions


If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?


Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums

Hoover U5344-950 My Hoover vacuum is a nightmare! I have had nothing but problems with it since day 1. The powerhead stops working if you try to lower the handle to vacuum. I took it in to be serviced and was told it sat on the shelf for too long in the store and it warped the belt...so it was replaced. Got it home, it worked the first time I tried it, then went right back to no powerhead working and as a bonus it is giving off a nasty smell like it is going to blow up! It now gets really hot to


... Hoover U5344-900 WidePath Vacuum

Sebo canister vacuum powerhead keeps stalling


... Sebo Vacuums

I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage


If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!


Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

VACUUM ONLY WORKS FOR 45 SECONDS THEN TURN OFF ITSELF. I HAVE TO WAIT FOR 10-15 MINUTES TO START AGAIN USING IT, STOP WORKING AGAIN AFTER 45 SECONDS. VACUUM IS NEW, I COULDN'T RETURN IT TO THE STORE I BOUGHT IT. PLEASE HELP ME TO RESOLVE THIS PROBLEM. THANKS


Sounds like it overheats quickly. But why are you not able to return it? ... Hoover U5750-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0910 seconds