Having problems with your Vacuums ?

I am having problems figureing out my hose diagram on my 1987 ford mustang 5.0 can you send me pics of where they go specifically


Answers :

Shy503p,
You will find the vacuum diagrams you desire in a Chilton's model specific manual for your 87 Mustang (just make sure the one you buy does in fact include the vacuum diagrams). You may also find it in a general domestic Chilton's that covers your year (I have one for up to 88 domestics) and I will check it for your diagram when I get the chance to dig it out.
Let us know how you fair, and Good Luck.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am having problems figureing out my hose diagram on my 1987 ford mustang 5.0 can you send me pics of where they go specifically


Shy503p, You will find the vacuum diagrams you desire in a Chilton's model specific manual for your 87 Mustang (just make sure the one you buy does in fact include the vacuum diagrams). You may also find it in a general domestic Chilton's that ... Vacuums

Picks up some of the dirt but does not send it to the canister it just stays in the base and clogs up the bottom hose. There is no suction on the detachable hand hose. Have cleaned out all filters and the belt is new. Cannot figure out the problem!


Have you checked all of hose,detatchable and fixed if it has any,for holes,kinks and blockages sounds like a lack of suction ... Vacuums

How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks


HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Dyson DC25 (which I've had for about a year and a half), doesn't seem to be picking up like it used to. There doesn't seem to be a problem with the brush bar, but I can't figure out what the problem is or how to fix it


Hi there,\015\012\015\012Sorry to hear you're having a problem with your DC25. You should be able to resolve this issue by following these simple steps: ... Dyson DC25 All Floors Bagless Upright Vacuum

I know the suction problem is a broken belt but cann t find my book to figure out how toi open the case to get at it


This URL would be a good place to start.\015\012\015\012http://www.retrevo.com/samples/Fantom-manuals.html ... Fantom Vacums Vacuums

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

My Dyson DC25 got stuck and wouldn't return to the upright position, I figured out that one side had jumped the track and gotten stuck in the square hole below the track. I did not want to break the plastic to force it back, so I removed the screw on the right side that was holding the kick stand on and removed the kick stand, also a spring thing came out. Problem is, now I have no idea how to re-install the kickstand. Can't find a technical manual or video anywhere, it can't be very difficul


... Dyson DC25 All Floors Bagless Upright Vacuum

Need instruction/care booklet for my Bissell powerforce vaccum model #3522-5. Bacfk of vaccum hose is filled with dirt and when attachment is used, dust & dirt fly everywhere. I don't have the care booklet for the vaccum and need to figure out how to fix the problem. Thanks


... Bissell 3522 PowerForce Bagged Upright Vacuum

Dyson DC14 roller doesn't turn but everything else works. The belt is on correctly, the roller is clean and it turns manually so I can't figure out the problem.


The DC14 has a "brush control system" operated by a knob on the right side of the base. This knob has two positions: "bare floors" and "carpet". The roller will turn only when the knob is on "carpet", and even then only when the handle is tilted back ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I recently lost power to the power head. Thinking the hose was not sending current to the head, I bought a new hose. It did not solve my problem. I have since noticed that a warning symbel is appearing that indicates what looks like a key with TA inside. The vacumn has good suction. Please advise John.


Hi\015\012\015\012Please check the link bellow to diagnose your problem…..\015\012\015\012http://home.howstuffw ... Electrolux Epic 6500 Vacuum

I am charging Remington Shaver FS360 for the first time I have put in charge for almost 12 hrs (the instruction is to charge it for 24 hrs at the first time) but still the charge led is not glwoing. I am not sure wheather it is still charging or not. Could you please help me out to figure out the problem.


... Vacuums

I have lost my manual for my bissell pro heat 2X and i can't figure out how to work it... is there any way you can send me some directions please?


You can download manuals from the Bissell website ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My vac. has no suction and I can't figure out what the problem is. Any suggestions?


Something is plugged, check the hose and any other port you can get at, before taking the unit apart for inspection ... Euro-Pro UV209 Upright Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

I have an old Hoky Omni carpet sweeper. I took it apart to clean the inside. Now I cannot figure out how to get it reassembled.(specifically the two buttons that open the bottom to discard the dirt, and two small wires that go somewhere)


... Hoky Vacuums

I have a model s3765 Hoover Windtunnel and it was no longer suctioning like it used to. I wanted to see if something was stuck in the rollers. I undid the screws at the base 3 of them and now I see there is a pic that do not undo these screws. I am having problems with getting them back in.


If you can post a pic of which 3 screws you are talking about and where you took them out of i can help u get it back together ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

HOOVER F5906-900 I am having trouble figuring out where the inner hoses go, A friend barroed it and took them off to clean them and did not put them back properly. Would you please send me Scamatics to see where exactly these go so I can shampoo my carpets before I go crazy. Thank You Misty Winslow [email protected]


Here is a break down, you may be to trace the lines:\015\012\015\012 ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

The Bissell Powerlifter is not sucking up the water like it used to and I can't figure out why. The hose extention works fine, the main cleaner is what is having problems.


... Bissell 16943 Powerlifter Wet/Dry Vacuum

Cant figure out how to thread elna 1000 lotus sewing machine. also the bobbin keeps getting tangled. if you could send me a diagram on how to thread and bobbin i would appreciate it


... Vacuums

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus


... Bissell 6595 Lift Off Bagless Upright Vacuum

My Miele Solution HEPA 5000 vacuum cleanr gives off a burning smell but will continue to run with a varying motor tone. I have not run it for more than a minute like this. I have reviewed responses to similar problems but cannot figure out how to access the motor. Can anyone advise?


... Miele S318 Bagged Canister Vacuum

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.


When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Vacume did not come with screws to hold handle to Vacume need the screws handle falls off vacume hits the floor [email protected] Model # 3041 Type - B2 The answer is simple, send the screws please this will fix the problem. Thanks Dr.Tracy Massie Dr.Tracy Massie Harvard;Dr/PHD; Chief Officer of Internal Medicine;Lead Surgeon Dr. Child Disorders; Princeton Dr. / PhD.; Chief Medical Officer; Lead Councilor


... Eureka 3041BZ Upright Vacuum

How do you thread an elna contessa 415. I have lost the manual and I don't seem to be able to find one. So if someone could send me a diagram of the threading instructions it would solve my problem.


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0338 seconds