Having problems with your Vacuums ?

I have small shed alarm. Movement detctor. Model kf-6 runs on 3 aaa batrries. i need instructions to change the factory settings


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have small shed alarm. Movement detctor. Model kf-6 runs on 3 aaa batrries. i need instructions to change the factory settings


... Vacuums

MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

I have a RICCAR 8900 - I have changed the belt and I think I did it correctly. Machine is running well, except the self-propelled portion isn't working. Vacuum only goes so far and then needs to be pushed, and yes I have it on the carpet setting.


Your vacuum is not self propelled. It is most. Likely something was not put back together properly when installing the new belt. ... Riccar 8650/8625 s Vacuum

Instruction Manual for Sears Kenmore Sewing Machine Model 158 13510. Need to know how to change the setting back to the straight stitch


... Vacuums

I purchased the Sharp Ultra-Thin Digital Alarm Clock Today. SPC431A The first one I bought the digits did not show up on the right side of the clock. I went and exchanged it for another, after showing the store what was wrong with it. I have now been able to set most all of it, but... 1) It is on 24 hr mode, instead of AM or PM. The instructions that I have do not say anything about a 24 hr mode. I have tried running through the clocks hours, to see if that would change it back to AM or P


... Vacuums

Product instructions need full view of internal schmatic and instructions on how to change belts or troubleshoot problems. I have the 1699 proheat and the 7901 Bissell I would appreciate a copy of operating instructions. Thank you, Raja Burns email address [email protected]


You can change the belts from the bottom, remove the brush roll, then you can reach thru slot to change the pump belt, then the cogged belt. Wasn't sure which darwing you wanted, if it is electrical, let me know.\015\012\015\012 ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My Oregon Scientific BAR888 has 5 windows, 1. temperature, 2. humidity, 3. mb/hPa or inHg (switch at the back), 4. bars showing pressure changes over 24 hours, and 5. time/date. Window 3 gives an option to set something between 0 and 2500. Oregon say they only have one set of instructions for the BAR888 but they do not match my instrument as there is nothing included for my window 3. Trouble is I don't know what the 0 to 2500 relates to and therefore don't know what to set it at.(My model does n


... Vacuums

Need to change belt. Need instructions. - Eureka 5859ASZ Bagless Upright Vacuum


... Eureka 5859ASZ Bagless Upright Vacuum

Need instructions I have lost the instructions for my Bissell AromaPro Upright Deep Cleaner is there anywhere I can download a set?


Try this link good luck http://www.bissell.com/Product_Search.aspx?Criteria=aroma+pro ... Vacuums

The retractable handle doesn't stay in place. a small spring came out near the button that you push to slide the handle up and down to change the length. i need to know where the little spring goes. there is a small pin that the spring fits around but i can't seem to get it to go back in place once the spring is on the pin.


... Panasonic Kenmore Canister Vacuum Vacuum

Model num. 052-8808-8 There are not enough instructions. Where is the manual override? I set the time at 2pm over the arrow and the T , want the timer to come on at 6o'clockpm., set the off time for 10 o'clock pm. Plugged the light in and it came on shouldn't it stay off until 6 o'clock. Need help!


... Vacuums

Need instructions for Vortex V2000 hoover as need to change the belt


... Vacuums

I need a small tube that runs from the water reservoir to the pump


Go to the hardware store with the old hose. They have several sizes and can cut to length for about a dollar. If you want it to last go to auto parts store and get rubber fuel hose. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Lost instructions,need to change belt


The customer operation manual can be downloaded from the hoover web site hoover.com\015\012\015\012the bottom cover comes off with 4 screws. install the belt on the motor, then roller, stretch to install roller into cavity. replace cover. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

I need instructions on how to change the belt on my Hoover Legacy II 820 vacuum cleaner


... Hoover Vacuums

I have lost my instructins on how to program this power center for my aquarium lights and need some help gettign anouther set of instructions


May I get the make and model # of the power center for the aquarium. ... Vacuums

I need to change from tools to floor


Happy to help. Please use this link to the manual:\015\012\015\012http://www.hoover.com/pdfs/manuals/F5871900.pdf ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Eureka Fantom Thunder 12V/older model Need instructions on how to change belt and headlights.I could only find 1 screw on the bottom plate none on top plate. Thanks N J


There are two screws on the Fantom Thunder (It was not made by Eureka though) on the back of the unit just above the rear wheels. Remove these two screws and the top cover can be removed to get to the brushroll, belt and headlights. I believe the lig ... Vacuums

Sebo X4 is squealing when pulled back. Takes a while after it's been running for this to happen. We changed the roller brush (needed it anyway) but didn't take care of the noise. Could the wheels be making this sound? At least that's what my staff thinks is going on... I own a commercial cleaning company and all we use are sebos... they're an amazing machine!


Yep - we think Sebos are pretty good too. I work at a Sebo sales and repair dealership! The wheels are a good bet - I can't think of anything else that might cause the noise. If in doubt, I suppose you could simply wheel one around for a while when s ... Sebo X4 Bagged Upright Vacuum

I need instructions for setting an Oregon Scientific Retirement Clock model RA2000. No luck with Oregon Scientific customer support.


... Vacuums

Help hi i have a eureka bravo model #9270 and i need instructions how to change the belt, i took out twoscrews it looks like the top comes off but it doesn't come off all the way.


The handle should be down and the top may have a tab on both sides to pry out with screwdriver. lay handle down and turn machine over. look closely around base between cover and there should be a tab to push on and cover comes off. ... Eureka Vacuums

Need instructions for how to change number 7 belts on bissell vacuum


Found the users manual online with directions for changing the belts. ... Bissell Vacuums

I need instructions on how to change bag in a Hoover Soft & Light Supreme upright vacuum cleaner. Thank you.


Hello,Here is a link that will show you how to change bag (and more).The model number of manual is not the same as yours but it will work for your machine. ... Hoover Soft Light Supreme U4262-930 Bagged Upright Vacuum

Engine troubles I have a 1975 4x4 GMC full size van. The motor is a 350 cid small block on propane. The thing hadn't been running in 5 years and when I tuned it up I changed vacuum advance pod on HEI distributor and hooked to a better vacuum and now the hotter it gets the faster it idols and when I try and turn the timing back, it starts hard. Wondering if vacuum is too strong or what is up?


I haven't fixed it yet but I think I might have a solution for it. From the factory this thing had a 4 barrel carb and they put an equivalent size atomizer in it for the propane and over the years someone omitted the EGR system in it and propane is a ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0807 seconds