Having problems with your Vacuums ?
A throw rug got caught in the rolling pin of vaccuum. Rolling pin no longer works.
Hello. more likely than not, the small belt that drives the roller has either dislodged or broken. Unless you have a dyson, you can replace that belt for about 5 dollars. The dyson, however has encased the belt in a plastic assembly and the entire assembly must be replaced for about 80 dollars. J.
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
A throw rug got caught in the rolling pin of vaccuum. Rolling pin no longer works.
Hello. more likely than not, the small belt that drives the roller has either dislodged or broken. Unless you have a dyson, you can replace that belt for about 5 dollars. The dyson, however has encased the belt in a plastic assembly and the entire ... Vacuums
Roller not turning when I drag vacuum across the rug. Got something caught in it, pulled it out, then stopped working properly.
Check the belt and what got stuck in it ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I just bought a dirt devil, started to vaccum got caught on a rug, and now the beater bar isnt working
... Dirt Devil Vacuums
Throw rug got caught in rollers and now it wont pick mup were are belts located on hoover windtunnel dual 5
Nylon belt in center of brush underneath . not a hard belt change. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
My shark bagless sweeper worked for about 6 months. Like a previous blogger, I caught the edge of a rug that jammed the sweeper, three red lights blink, the brush is free moving yet the sweeper will not work. I did leave it plugged in all the time otherwise it would not run but for minutes. Very disappointed. New battery? what if that doesn't work? is it junk then, money down the drain.
This will probably cost you more to repair than to buy a new one. Does it turn on at all? ... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray
Took my vaccuum in for service recently and not sure I got my vaccuum back. Doesn't work very good and looks a little different to me. Trying to verify the serial number to compare to my records....is it the bar code number on the bottom?
The serial number for all "G" models, containing 10 digits, is located on the side of the machine above the hole the bag attaches to. ... Kirby Ultimate G Bagged Upright Vacuum
The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.
Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum
When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.
Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum
My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.
Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum
My roomba no longer works on my area rug, it starts backing up continuously once it encounters the rug.
Sorry to read about your problem, I hope this helps you out.iRobot Roomba Vacuuming\015\012 Robots and the iRobot Dirt Dog Workshop Robot are equipped with four \015\012infrared Cliff Sensors that prevent robots from falling off sta ... Roomba Robotic Floor Bagless Vacuum
My Hoover Deluxe Rewind Elite will not pick up anything. My daughter got something caught in it last night and it made that noise when you get something hung. We turned it off but today it will not work. Is there a reset button?
When you are saying "today it will not work" do you mean the motor runs, but the unit will not vacuum, or are you saying nothing happens when you try to turn it on?If the motor run's, the belt probably broke. You will need to remove the b ... Vacuums
Electrolux vacuum brush not turning problem: was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won't even switch on. Hope you can help
Under the vacuum, there is a guard.\012remove the guard , either by 2 screws or by 2 clips.\012there is a belt under the guard.\012that is connected to the brush.\012the belt need to be replaced. ... Vacuums
Havent used for about two years. I had to put the belt on it. It doesnt seem to be sucking up very well and after about 15 minutes of vaccuuming the bag was empty. My house got really dusty. I know the rollers were spinning because i looked. I could hear some dirt going in but could definatly tell it wasnt working properly. Is it in reverse or something?
After two years you need to make sure the bag is connected properly and inspect it for tears and that the hoses are connected correctly and not deteriorated. Make sure the hose is clear. You should be able to feel the suction at the end of the hose. ... Vacuums
Dyson 18 slim the rotating brush bar will not rotate. Was working fine until I got the edge of a tablecloth caught in the brush, pulled it out ok but now the brush will not rotate fast, but will rotate by hand . Any ideas.
If the DC18 has a proteted belt then it will have to be replaced by a Dyson engineer or repairer. If the cleaner has a removable sole plate where the beater bar is then remove it and replace the belt - sounds like the belt has snapped and needs to be ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum
My Dyson Ball rug attachment won't work - something had caught that I cleared, but the reset button does not reset the vacuum. This happened once before and I had to take it in. Is there another way to fix this simple problem?
... Dyson Vacuums
I have a modelF5914-900 steamvac cleaner.serial #0704 0011 4711 I cleaned the carpets in my house and then started to do the stairs with the stair attachment. I got down to the last four stairs and the solution would no longer come out. I checked the tank and hose connection and tried priming the pump per the instruction manual. nothing worked. Could you make a suggestion as to what the problem could be? Thank You
Check fuses goin to the pump, is the pump working? if so you may have an air pocket or a air leak in the intake. ... Vacuums
I have a bosch bagless jet 12 amps/1450 W which I got secondhand. the switch to operate the powerhead (the rug brush) no longer gives me any results. I don't have the right tools to unscrew the plates and look for a belt. I don't think it's a belt problem anyway because I don't hear the powerbrush motor turn on, either.
... Bosch Vacuums
I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No
Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums
While using my Dyson a rug got caught and that ratcheting sound started. I removed all signs of strings, etc until the brushes rotated fine but when I started the Dyson the ratcheting started again. I have the DC 14 Animal.
The rattly sound means the drive belt has snapped or the protective clutch has slipped. This needs repair by someone who knows how to repair Dysons officially. Sadly its the kind of model that can't be done by the owner. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I was vacuuming with my dc17 and it caught the corner of a throw rug and the part that makes the brush turn won't turn on now.
Sounds like you need a new belt ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My vaccum has a 3 position handle. This no longer works, so I have to pick up vacuum to move it. Makes it hard to vacuum scatter rugs. It does not lock into place
What is the brand and model of the vaccum? the description i see says Hoover U6311930. When I check the info for this model it gives me maytag vaccum cleaner. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum
Vacuuming a small rug and it got sucked up a bit and now my extension won't work.
Make sure the little red reset button is pushed in on the power nozzle. ... Rainbow 75th Anniversary Canister Vacuum
Dyson DC07: When I first got this vacuum, it was so powerful that it lifted my area rugs off the floor. It is so weak it barely works. I have removed and cleaned the filter, but I can?t seem to improve the suction. What am I doing wrong? How do I fix it?
Hello,\015\012\015\012If your vacuum runs but still leaves dirt behind, the culprit could be the drive belt or an obstruction. If the agitator brush slips or won't turn, the belt is bad and needs to be replaced. If suction is weak when yo ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
My dyson DC17 animal has started to make an extremely loud noise after a rug got caught in the roller brush. What do I need to do to fix it?
Probably a flat spot on the belt, replace the belt ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
O.k. this is the 3rd time I'm writing this...not even sure how many times I'm being charged.... Already aggravated and exhausted so Please, Please help me. I bought 2 Westek 1 outlet timers for our Bearded Dragons. They have to have 12 hours each of specific lighting (day and night). I get the "up" are off times and the "down" pins are on times. The problem is the Clock Isn't working.... Any ideas??? I'm about ready to throw them out the window except we're leaving early in the morning and
There is no money indication on this one. I'm speaking for free, so I hope you're asking for free.\015\012\015\012\015\012Oh yea, I already answered this question.\015\012You bought two bad timers!\015\012\015\012Sorry. ... Vacuums