Having problems with your Vacuums ?
Nilfisk advance floor scrubber vacuum problem
\015 I have been troubleshooting a frequent loss of vacuum problem with a nilfisk advance micromax floor scrubber. The motor pulls good vacuum and the hoses nor filter are plugged. The water stop ball is not the problem either. Any other troubleshooting ideas?\015
CAN YOU HELP? I AM LOOKING FOR A SMALL FLOOR POLISHER AND SCRUBBER FOR MY OWN USE AT HOME. i SHOULD HAV TWO 5_6" SCRUBBER PADS AND FLOOR POLISHING PADS. THANK YOU AND GOD BLEES. [email protected] LOWTON , OK
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Nilfisk advance floor scrubber vacuum problem
CAN YOU HELP? I AM LOOKING FOR A SMALL FLOOR POLISHER AND SCRUBBER FOR MY OWN USE AT HOME. i SHOULD HAV TWO 5_6" SCRUBBER PADS AND FLOOR POLISHING PADS. THANK YOU AND GOD BLEES. ... Vacuums
Vacuum cleaner I am needing to buy a vacuum cleaner - the flooring in our house is mainly oregon pine with loose rugs. I suffer from back problems and find the cylinder vacuums cause a great deal of back strain. I have been told that an upright vacuum is not suitable for wooden floors - I would appreciate any advice, particularly if u know of an upright vacuum cleaner that works well on wooden floors Thank you
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=517227&thid=728380\015\012Vacuum cleaner\015\012Posted by che9 on Jul 01, 2008\015\012I need to buy a vacuum clea ... Electrolux EL7055A Bagless Canister Vacuum
My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed? thanks
Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track. ... Hoover Vacuums
My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.
When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum
Vacuum problem i have a bissell total floor velocity and everytime i turn it on it makes this really loud noise like it's about to exploded. We changed the belt but that wasn't the problem and we just bought the vacuum a little over a year ago.
Check the brush roll, do the ends turn freely, if not, replace it. Could have a clog in the hose or the dirt inlet by the brush roll, the other could be a bad motor. ... Vacuums
Hi good day, I have a Kenmore Grab n Go 12.0AMPS Vacuum cleaner, Model# 116.34722402 & serial#T53601507. The vacuum is now having a problem whereby the rolling brush underneath is not spinning when the vac is on. This has caused it to stop sucking up dust. Could you please advise as to what might be the problem. Thanks in advance for your kind assistance. regards, Clarance
... Kenmore 34722 Grab-N-Go Upright Vacuum
I have a Kirby G4 Vacuum Cleaner - MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I've had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
Hello,\015\012My educated guess is that it's either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair...\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum
Hi folks, my beam vacuum makes a very loud roaring noise quite often. the problem started when i was vacuuming up a quantity of vermiculite from my chimney. i think i overloaded the vacuum i think and it made this loud roaring noise. the vacuum tends to make thos noise when i am hoovering after 5 minutes or so. any ideas?. thanks in advance Tom....
If the filter bag is bad and didn't trap all of the dust, then it got into your motor, so you may have a problem with your motor now. ... Vacuums
My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?
Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums
Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!
Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums
I have an old Progressive vacuum cleaner that says "Hepa Filter" and "Whisper Belt". Not sure what the model # is. The problem is that the vacuum part itself (the part that touches the floor and rolls over) has ejected its filter that we can see through the little window- it just came out under the rollers under the device... we cannot see how to re-insert this piece of filter which looks like a kind of round, flat grey foam/fabric and clearly goes inside- (top of the part that touches the flo
Check this procedure:\015\012\015\012Unplug the appliance that you will be \015\012changing the filter in.\015\012\011\011\011\011\011\011\011\015\012\015\012\011\011\011\011\011\011\011\011\015\ ... Kenmore 23313 Whispertone Bagged Canister Vacuum
Vaccum is making a loud high pitched sound, doesn't work well through the hose or the floor piece and shuts its self off after about 5 minutes. I have cleaned the entire vacuum out several times but this problem persists. Usually after I clean it, it'll work for a couple months, not this time. Vacuum is only 2 years old, is this typical?
... Dirt Devil Featherlight Bagless Upright Vacuum
We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu
Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum
I have a Kenmore vacuum cleaner model #116.34720. The problem I am having is that if you are rolling the vacuum around, the base will drop without pressing on the handle release pedal. This often results in a bunch of dirt being dumped back out. The manual doesn't show anything about adjusting the handle release pedal so it holds the handle and base in an upright position better. Any help is greatly appreciated! Thanks in advance!
I am having problems with the roller on my Oreck DTX-1300. It turns on and off intermittantly while I'm vacuuming. I have completly taken it apart and cleaned and inspected the roller unit.(I am very much mechanically inclined) This has stumped me, I have checked the electrical from the vacuum to the floor unit, and everything else that I could think of. Question: what does the metal sensore plate on the bottom of the roller unit do?? Anything anybody can tell me, I would greatly appreciate. Cap
... Oreck DutchTech DTX1300A Bagged Canister Vacuum
Just purchased Floor Mate. It will not dispense cleaning solution. It will pick up water on floor and vacuum. Brushes rotate, no other problem.
Either a problem with the valve at the bottom of the tank, or where it sits is called the reservior asm, a rod in the handle hits to release the water, so your problem could be in that area. But you have a years warranty on it, take it to a warranty ... Vacuums
Carpet/Floor Switch problem on Hoover WindTunnel Vacuum
Well, you have to deal with it, you have to play with this electrical things if you want to fix this problems.\015\012\015\012The good news is, the sources of the problems is the switch already\015\012broken.The first things before you do ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Dyson vacuum I have a DC07 vaccuum. The problem I am having is that the front does not want to stay down as I vaccuum and I continuously have to keep stepping on the front to make it go back down to the floor. It seems as though there is either not enough weight in the front or possibly the unit just has to be broken in so that there is not so much resistance between the handle and the front of the vaccuum. Could there be something I did not remove or is this typical on these vaccuums?
There is some thing broken it is two plastic cogs they help the front go down and stay up you will have to get a star screw driver and there should be two screws on top and two at the b ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I have a kenmore model 11625512506 vacuum cleaner. The problem is when I select "floor" on the handle it does not turn on, it only turns on if I select the "carpet" function and it is attached to the Power Mate. This means that I can not use any other tool or function other than the carpet one.
... Kenmore Vacuums
The motor overheats and shuts off. This annoying because it has done it at least 5 times today during normal vacuuming. It shuts off easily when you use the hose and canister to clean the steps or around the floor. What can I do to alleviate this problem?
Almost all vacuum cleaners have a thermal cut-out, which operates when the machine gets too hot and resets automatically when it cools down. Overheating is almost always caused by a blockage. Either the filters need cleaning or changing, or the ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
Proteam Pro force 1500xp Upright vacuum... When I switch to the carpet setting I have no suction power but the beater bar is turning. If I switch back to the floors setting, the suction is excellent. Wondering if the problem is in the on/off switch?
Just undo the screws on the front part of the switch assembly, carefully check all the leads to the switch. Mine slide off all the time as the switch is poorly designed and subject to damage when the darn thing tips over (easily!!!) new switches are ... Proteam ProForce® 1500XP Bagged Vacuum
MY WIFE BOUGHT THIS FOR ME FOR FATHERS DAY GIFT ABOUT ALMOST 2 YEARS NOW OR SO,BUT I HAVE THIS PROBLEM THAT THE BRUSH DOS'NT SPIN ANYMORE EVERYTIME I PUT THE SWITCH ON FOR BRUSH ON,THE HOSES BRUSH SPIN IS WORKING BUT FOR THE FLOOR CARPET BRUSH SPIN IS NOT WORKING,AND THIS IS THE MODEL NUMBER OF MY HOOVER VACUUM CARPET SHAMPOO CLEANER IT'S F7411-900
This unit uses a turbine assy to turn the brushes. The brushes could have something jamming them. Remove the brush unit, it is held on 2 spring hooks 1 on each side. The brush unit is driven thru a 1/4" square post, only one brush is driven and it dr ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Kirby Ultimate Diamond Edition G Series, upright. Problem: I lost my manual. How do I use my vacuum on hard wood floors? How do I use attachments, where do they attach?
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=576029\015\012Generic problem for all Vacuums\015\012Kirby Ultimate Diamond Edition G\015\012Posted by jlutsi on ... Vacuums
Brush won't engage on my hoover windtunnel vacuum. I see the problem is that the "carpet / hard floor" slide bar is broken / jammed. How do I access the slide bars from below to unjam them?
... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum