Having problems with your Vacuums ?

Replacing and connecting

\015 I need help on replacing a motor to my sanitaire vacumm sc887-b\015

Answers :

From the bottom, remove the the fan cover and fan. Then remove the top cover, it is held on by 2 springs that you remove from the bottom, and then the screw in the HT. adjustment knob. Take out the four screws holding the motor, then the motor will come out. Part # for a motor is 54352-11, or you can rebuilt your old one. Go to a repair shop and they can order what you need.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!


... Kenmore Vacuums

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Where can I purchase replacement batteries? The original are BYD Model D SC1500Px3 NiCd. 3.6v, 1500mah. They are a solder connected 3 pack with connecting tabs.


... Lectrix 0301 Cow Vac Handheld Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Looking to replace my eureka Boss central vacuum, but need a new unit with both exhaust and suction connections on same side. I was looking to replace it with an Imperium CV7700.


I would recommend the AirVac AVR7500 model. It's a great unit. ... Eureka CV1801 Bagged Vacuum

When connecting the wand into the brush component. sporatic power (sometimes runs sometime nothing) the power is on again off again. when hold pressure down on the wand the power stays on. do you think the coupling connection is bad on the wand? would the wand replacement likely be the culprit?


There is is switch or sensor in the connection. Likely that piece is worn or shorted out. You may be better off getting a new wand piece ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

The power head keeps shorting out during use. one of the connecting prongs from the handle to the power head is black instead of silver and is smaller in diameter like it has been arcing inside the connection. could this be the problem and if so can I replace it or will I have to take it to a repair facility. Thank you for your help, Jim Carey [email protected]


This is a problem with the connection in the wands and the powerhead. Because they are shorting out you may have to replace the neck on the power nozzle. (Leave that to a pro). But you will definatly have to purchase a new wand as replacement wires a ... Electrolux Lux 7000 Bagged Canister Vacuum

Want to replace connection pipe part #KC92PBZTZV06 that goes into the cannister. Want to seperate it from adapter #4370325 without breaking it. I have the new connection pipe.


... Kenmore Vacuums

TRYING TO REPLACE THE PLUG ON An ELECTROLUX Z5915 1600W vacuum cleaner, IT HAS TWO WIRES from the cord.....BROWN AND BLUE.....BUT 3 POSSIBLE CONNECTIONS ON THE PLUG NOTED N, L and the earth connection.


... Electrolux Vacuums

Need replacement collar with 3 pegs connecting


Have been in touch with Rowenta spares agent and am\015\012told no parts available for model RB02, so will have to\015\012improvise ... Rowenta Vacuums

How do I remove the collar to replace the cord to the power bar, I have the part, cannot get the little collar off to connect the new wire, purple to white and white to black... cannot get the old wir


... Hoover Powermax S3530 Bagged Canister Vacuum

Model v1945zn, handel broke at base and doesnt connect to sweeper where can I find replacement part


... Shark Vacuums

Replacing and connecting


From the bottom, remove the the fan cover and fan. Then remove the top cover, it is held on by 2 springs that you remove from the bottom, and then the screw in the HT. adjustment knob. Take out the four screws holding the motor, then the motor will ... Vacuums

Im trying to replace the belt but cannot find where to connect it


Vacuums are different.  Look for a small motor shaft within the belt's reach. ... Vacuums

WH5205 upright vacuum power cable replacement. How do you get at the cable connections inside? HELP! :(


... Hoover Vacuums

Replaced the pump and solenoid on my Bissell Proheat, model 9200 H, but not sure I got the tubing connected back right. Can anyone help me with this?


... Bissell 9200 Upright Vacuum

Wiring Two wires (black and red) connected to the slider on/off switch have overheated and melted away the 90degree connectors. Will replacing just the connectors solve the problem or is it more complicated, such as a resistor, capacitor, etc.?


This is easy and hard. If only two wires connect to the switch, cleaning up the connectors and replacing damaged items should fix it. Don't do anything unless the unit is unplugged. Try this first: connect the two wires together and tape them up. ... Electrolux EL5010A Bagged Upright Vacuum

No suction I just replaced the bag, and normally after this I have a lot of suction. Now that I have changed the bag I have less suction that I had before. Not even enough to picj up dog hair. I snaked he hose and checked all of the connections. It seems to have an air leak but no amount of tape will fix this. I cleaned the filer as well with warm water and dried it and re installed but still absolutely no suction. I am ready to throw it out! Any suggestions would be appreciated


1, Does the blower (discharge) side blow bunches of air??Yes: Something is clogged from the bag to the hose end. Try blowing out the hose from the discharge side.Or: The bag is not properly seated. Make sure that the plastic piece is ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Rod problem... One of the electrical connection posts that are on the top of the rod appears to be broken which causes the power head to work only when it makes contact. Is this repairable? If not, is it replaceable? If not, are the rods available for purchase? The vacuum cleaner itself works well,


You would need a new wand. this might work for your unit. ... Fantom Vacums Lighting Canister Vacuum

I need a replacement power head plug the progs are no longer connecting and it is shorting out. I have a GE 106766 A-3


... GE 106766 Bagged Canister Vacuum

I need to replace the power cord on my Eureka 2271, and would like know how to get into the connections?


... Eureka 2271 Bagged Upright Vacuum

I'm using a Eureka maxima 12 amp vacuum and where the hose is connected to the vacuum by a screw that part is broken where do I find a replacement hose that includes the clear plastic part that I can attatch to the vacuum?


... Eureka 4700A Maxima Bagless Upright Vacuum

The power wand electrical connection on the power unit itself seems to be corroded. I think I need a new two wire plug to plug into the wand. the model is a Eureka 6984 A. I am able to disassemble the power unit if necessary and replace the wire and plug if one is available


Try hesco inc they have a on line store with all the vacs parts diagrams and fast shipping. ... Eureka Vacuums

Power cord I purchased a new cord. The one on my vacuum is frayed. How do you get to the connection to replace it? Thanks.


May need to break the unit down to replace the cord,there should be some tec screws under the belt cover to remove the motor housing cover, may be two to thee wires. the rest should be simple. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0476 seconds