Having problems with your Vacuums ?

Sigma aquatron electric shower,old went bang and smoke from the back,how does it fit so I can replace

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sigma aquatron electric shower,old went bang and smoke from the back,how does it fit so I can replace

... Vacuums

Replacement motor I purchase a replacement motor for a F5897-900 Hoover SteamVa Motor part # 43576197 or 27242051. The replacement motor has three electrical connectors + ground were as the orginal has two electrical connectors + ground. Do I ingnore the the thrid connector and hook up the wires to the same connectors as the orginal or do I have to do some rewiring.

The manual only show one wire from the motor going to the switch, the other going to the cord, then the ground wire. I would wire it the way your old motor was, could be that some models maybe were 2 speed and the other wire would be used for that. ... Vacuums

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus

... Bissell 6595 Lift Off Bagless Upright Vacuum

Replacing electric harness in Beach Soft Touch handle

... Beam Industries Wet/Dry Auto Central System Vacuum

Smoking after fitting belt on dc07

... Dyson DC07 Bagless Upright Cyclonic Vacuum

We bought a new home in march. It is a brand new home, with brand new First Alarm smoke/CO detectors. The very first night, we noticed the iving room (main) smoke alarm was "chirping". So we tried to replace the batteries, but when we did, all of the smoke alarms started going off (they are hardwired). We took out the new battery & dealt with the chirp. It is getting to be too much. So we are trying to fix it, but everytime we replace the batteries, the alarms are silent for a little bit, & then

... Vacuums

Fitting a new electricity cord

The cord has been damaged, how do I replace a new one, what parts have to be dismantled to get to the inside of the cleaner ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Can the suction hose fitting where it attatches to the base be reattatched, it has torn away from the snap-on fitting or do I have to replace the complete hose unit, the model is F5878-900.The existing hose is screwed into this fitting and glued.

You must replace the whole hose unit. its not very cheap either ... Hoover F5878-900 SteamVac Upright Vacuum

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef

Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

Where can I get a replacement glass lid for Rival crock pot model #3100/2? The one listed below is out of stock, but, even if it were, it will not fit my model. Any suggestions? "Buy-it-now-store.com" lists: CURRENTLY OUT OF STOCK, NO ETA. # Rival Crock Pot Lid Replacement Glass for 3.5 Quart Rival Slow Cookers - $5.99 Rival Crock Pot Slow Cooker Replacement Round Glass Lid Cover # Works with Rival Crock Pot Models: 3100, 3101, 3102, 3103, 3130, 3133, 3120, 3250 # Approximate total

... Vacuums

Replacement motor I am undertaking the repair of an old dustbuster as a training exercise. ,The motor in my V2410 is Made by Johnson Electric but I cannot find reference to the numbers marked on it on the manufacturers website. Are you able to give me a model number for an equivalent replacement or the specifications of the original motor? Thanks, Gary.

... Black & Decker V2410 DustBuster Handheld Vacuum

Looking to replace the head of a Braun 549 series. Can't find a replacement. Was told the 7000 series would fit and they aren't the same. Please help???

Http://www.amazon.com/Braun-70S-Cassette-Replacement-9000/dp/B001VEK1HQ/ref=sr_1_1?ie=U ... Vacuums

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest

I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

On a filter queen 360 vaccum the electrical connection from the hose to the wand was loose and over time the electrical arcing burned up the female conector piece. Is there any way I can replace this without having to buy a new hose! Where would I find this female conector piece.

I am having the same problem On a filter queen 360 vaccum the electrical connection from the hose to the wand was loose and over time the electrical arcing burned up the female conector piece. This sounds to me like a manufac ... Filter Queen Vacuums

I need to replace electrical cord on hoover windtunnel UH70120. How do i get the cord reel off? Can i open the cord reel to replace the cord?

... Hoover Company Wind Tunnel U53019 Upright Vacuum

I was trying to repair my wife's kitchenaid mixer and took part of it apart, including the back part, where the electrical connections are. The original problem was the plastic gear was damaged -- I finally had the good sense to find the solution for that problem on the internet and replaced the damaged part. But now the mixer just won't turn on. I don't think I damaged anything in the electrical section, but I suspect I either blew a fuse or somehow disconnected something.

Do you have a model number? Is the voltage getting to the motor from the switch? ... Vacuums

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.

... Eureka 431A Optima Bagless Upright Vacuum

I have bought new Hoover bags on two occasions. The first spares I bought were the Xxxl variety and I didn't think they fitted that well. The next spares I bought were the type g megafilt. I still feel like they do not fit that well and the suction power on the vacuum is not as good. I'm I buying the correct replacements? I followed the guidelines on the Hoover bags the vacuum came with. These were printed as the right bags to buy. I only have the vacuum around a year and thought it was brillian

... Bosch BSG71310UC Bagged Canister Vacuum

Smoking belt Hey I have a Eureka 2961 avz bagless vacuum, and if it's on for a few minutes i can smell the belt burning.  If the vacuum is left on any longer the belt starts smoking.  I took the case off and there was a little debris but not much.  Is there a cause and fix or just time to replace the belt?

Belt is slipping because the bearings on the beater brushes, which it turns, are jammed or full of dust. \015\012Alternatively the belt has stretched after being overheated and needs replacing because it now slips. ... Eureka 2961AVZ Bagless Upright Vacuum

Model, 116.c85pbpk0v022 Power-Mate Jr. attachment stopped working, could it be a part within the unit (i.e. the electrical component) or do I need to replace the unit? How do I troubleshoot the electrical connection? No known drop or abuse. Worked last time I used it.

This model frequently stops because, lint, hair, etc. gets caught between the two end pieces of the brush cylinder. Do the following to fix it:1) Remove the two Philips screws from the underside of the unit. 2) The side with the tag will ... Kenmore Vacuums

Nilfisk GM 90 motor bearing Hi I have replaced the motor bearing on the GM 90 model but having problem with re fitting the turbyne I forgot the sequence it has 2 turbines and 4 2 inch washers Can you please tell me the sequence it is fitted Thanks,,,Ps the motor is 100% ok now Peter

... Nilfisk Vacuums

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.

Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

I have a Holmes HOH-2400 oil filled heater. one switch of the double lighted switch has failed now only allowing me to use the 700 watt setting only. Whre can I find a replacement switch to fit. It will be an easy replacement

... Vacuums

I replaced the battery into the smoke alarm and the smoke alarm kept intermitentl beeping all night long anyway

... Vacuums

Polti 2400 I am trying to remove the casing from the steam cleaner to fit a replacement wheel. The screws holding the casing are similar to torx but they have a raised centre which means they can't accommodate a torx screwdriver. I thought this was going to be easy just replacing a snap-in wheel!

You can buy T15 torx driver with hole in them from link below. ... Polti Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0601 seconds