Having problems with your Vacuums ?

My grundig yacht boy 400 has a broken antenna and I would like to repair it. It came off , has small screw still attached at bottom. Need to take apart radio and don't see how. Thank you, Lourdes

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My grundig yacht boy 400 has a broken antenna and I would like to repair it. It came off , has small screw still attached at bottom. Need to take apart radio and don't see how. Thank you, Lourdes

... Vacuums

The self propell does not work... i turned it over and took off th bottom plate and can see where the cable is suppose to be attached to the drive system, but it is no longer atteached, so it came out or a piece of the vaccum broke as it seems to be alot of plastic.. i see a screw and the end of the cable is still there... But where does it attach and how do i do it.. i havent taken the complete houseing apart yet as i have never done that before and wasnt sure about all the scres and what not..

... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

No suction i have been using mine for like a year or so. today i went to use it and then no suction. the water comes out but it wont **** it up. I haven't had any problems till now. I cleaned the little red filter but still nothing. I dont wanna take it apart with out knowing what im looking for.

I had exactly the same problem with my five-year old my Bissell 7920, and it's probably a broken pump belt.  See page 19 of your instruction manual for how to replace.  The Bissel ProHeat belt accessory pack costs $3.99 and you get a pump b ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

How do I take apart the body of dirt devil 82500? I think something shorted out, and want to see if I can fix it. I took all visible screws out of body, but still can't separate the two halves to get to the motor

This is sort of easy, and hard at the same time. \012\012First remove the dirt canister and hose. \012take out your exhaust filter. \012find all of your screws on the one side of the unit and remove them. \012you will fi ... Dirt Devil MO82500 Bagless Canister Vacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I

You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

I have a remington hc 822 it does not cut at all.if i try cut it pulls my hair.i tryd taking it apart but it still doesnt work.and i want to also knw how 2 reassemble it cos i am quite confused .i got it second hand so i dont have a manuel.ue assistance would be very much appreciated .

... Vacuums

Upholstery attachment The nozzle doesn't spray properly, the water just pours out (not alot) instead of spraying. It also has very low suction. The upright part seems to be working fine. I cannot figure out how to take it apart so I can look for a clog, when I look into the hose I don't see anything.

May have a problem in the noozle asm on the hose. Hose part #90001335. \015\012 \015\012 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

Hello i own the bissle proheat steamer it turns on but no water or soap or suction from floor or the utensiles ive taken the take off the back to scope out anything that could be in the way but dont see anything the motor is making that clogged vacume noise witch makes me believe something could be stuck somewhere in it but it could also be no water is getting to the pump or despencer but the brissels still work belt for that is good where would i be best to check and where is the location of th

... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I opened the cannister to change the bag and when I closed it the motor switch will not turn on. The second position which turns on the attachment for rugs still comes on. We thougth it was the switch so we ordered the part and it is still doing the same thing. Is there a reset button somewhere inside? The only reset button I see is on the attachment which is working.

It can be a few things. First check the overload protector located on top of the canister. If it has tripped the unit will not run. Push it in to reset. \015\012If that is the problem check the motor safety filter to see if it is clogged and caused t ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My steam mop gets hot but steam is not coming out when i pump it. However when I release the bottom attachment steam comes out of bottom of the base (purple part). I took the attachment off to see if it was plugged but dont see anything. Any suggestions?

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

E series How did you take your rainbow e series apart? Do you have a manual? I've got a few pieces off mine but can't see where any other screws are to completly take apart to be able to look at motor. Thanks Kelly

The clear lenses on either side of the top part of the E-series Rainbow are removable. If you look at the each lens you will see two sections on the top edge of each lens that looks like this |___| |___| about 1 1/2 inches in from each end. Put a ... Rainbow E series Canister Wet/Dry Vacuum

We had to take the machine apart just to see that the belt had broken after only 5 use's . We can not see how we are ever going to put the new belt back on. do you have instructions on how to take the belt off and how to put a new one on? Please send me one.

I have a Panasonic MC-V5746 upright vacuum. According to the booklet, \015\012MAKE SURE UNIT IS UNPLUGGED.\015\0121. Place carpet-bare floor selector in "carpet" position.\015\0122. Remove lower plate (there are two screws in the m ... Vacuums

Cable stuck in machine (sphera 20). How do I take apart to release cable please? I cannot see any visible screws to take the machine apart. Cable will not retract or come out of machine

... Bosch Vacuums

Bissell Healthy Home Vacuum brush stopped working. The hose attachment works fine, just the brush on bottom. Without taking it completely apart, it shows no sign of blockage. Any suggestions? Or, will I have to take it apart?

You will have to remove the bottom plate to get at the brush. The drive belt either slipped off or broke, this will have to be replaced. ... Vacuums

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?

Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Hoover F5809 Hello, I seen a few of your post and was hoping you could help me. I just became a member today. My sister gave me her old Hoover Steam Vac-Model F5809. This thing is so dirty and clogged because my sister has pets. So far I've gotten it all taken apart to clean it. I'm not a newbie and taking apart and fixing things. I have fixed things like microwaves, washers, dryers, dishwashers (still learning about TV's-very hard, hehe). Anyway, I got what I believe to be the motor cover off.

That cover is the called the fan cover and is usually pressed on. Tapping on the edge with a flat blade, you may be able to get it off and hope you don't bend it up, you will to put it back on tight enough so it will stay in place. Another thing to ... Vacuums

My filter queen just had the motor rebuilt last year and was basically a brand new unit when I got it back. It is not picking anything up now when I vacuum. The beater bar on the carpet attachment is turning fine and when I take all the attachments off the hose I can feel the suction being created like it should be picking up debris just fine. I have emptied the canister even when it did not have much in it; however, it still will not pick anything up off the carpet. It picks up debris tempo

It sounds as if you have a clog inside the "Power Nozzel". They mention that there are "no user serviceable parts within the Majestic® Power Nozzle" My advice would be to see if you can see a clog with in reachable distance and try to remove the ... Filter Queen Vacuums

My Dyson DC17 has lost suction on the wand and is not picking up dirt as it should. I have taken the small part at bottom of the machine off to see if there is a blockage--none that I can see. The flexible tube on wand is very tight and won't extend very much. Dyson sent me a new cyclonic part in April but the machine still doesn't seem to be working properly. My serial number is 260-us-d11545. Is there somewhere I can take my Dyson to get it fixed. I'm very frustrated with it. Thank you.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How do I replace the motor brushes in my DC11? I cannot dismantle beyond removing the pipe attachment. I've removed the 6 fixing screws that are visible, but the machine is still firmly "together" as if there are still screws that I've not located. Does it snap apart? Are there hidden screws? Paul

You can buy brushes but if the armature is overheating changing the brushes wont help ... Dyson Vacuums

A baby sock was sucked up and stuck where i can't see it in my regina electrikbroom cleaner - 11.4 amp. i have tried to get it out and now i have to take it apart i think and can't get the housing apart - what should i do?

... Regina ElectrikBroom RG100 Vacuum

Vacuum brush Well thank you for your response but how do you remove the brush cover plate? I looked to see if I could unscrew it but i dont see any screws. I don't know how to take it off

... Kenmore 22812 Bagged Canister Vacuum

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!

... Kenmore Vacuums

HELLO I have an Oreck Orbiter Floor Machine, It makes a lot of noise. I seems like one of the side screws fell out. I did not see this happen. Nor did we see any loose hardware. My question is - How do I take it apart... to inspect inside. thanks SUsei

... Oreck Orbiter Floor Machines ORB-500, ORB-550, ORB-600 Vacuum

No suction I live in a house with two bernese mountain dogs... very large animals who shed a LOT.  I've cleaned the filters, the roller, and gotten as far into the hoses as I can without taking the entire machine apart.  It's still not cleaning as well as I know it can... nothing is making it into the debris receptacle.  What can I do?

Hi elora,\015\012\015\012I live in a house with three shedding cats. I also have the same vacuum. About twice a year, I have to getinto the area of the vacuum where the motor is. There is a little pring loaded vavle that sometimes gets ... Bissell 3590 CleanView Bagless Upright Vacuum

Power cord Cord is just all knotted a twisted, i bought a rubber cord and just want to replace the original. I have removed all the screws from the rear of the machine and it still doesn't want to come apart and i dont want to force it. any help is appreciated.

If the cord goes in at the top, take the handle off, then remove the tool holder, then you can get to the cord. If it goes in at the bottom, You have to take off the motor cover to get to the connecting end. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0547 seconds