Having problems with your Vacuums ?

We have A "WC1000" 12 cup Coffee maker. It is leaking water out the bottom of the unit. We have removed the bottom metal plate, but there is nothing in that area requiring attention.

Answers :

I think a gasket may have melted, or is leaking. Also check the ends of the little hoses. they may have cracked.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have A "WC1000" 12 cup Coffee maker. It is leaking water out the bottom of the unit. We have removed the bottom metal plate, but there is nothing in that area requiring attention.

I think a gasket may have melted, or is leaking. Also check the ends of the little hoses. they may have cracked. ... Vacuums

On the bottom of the Fantom Fury where it states:"The United States and Canada utility patent....". Now go to the far right end of this statement (the end opposite the spring, well I have a crack in the plastic which, when toggled, moves the entire plastic underside of the vacuum to move. In other words, I think I need an entire bottom plastic plate. The cracked area also makes the foot lever (which lowers or locks the vacuum handle) not work as the crack makes it impossible to work. I know

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=545424\015\012Generic problem for all Vacuums\015\012On the bottom of the\015\012Posted by c ... Vacuums

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.

The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

Dirt smell I seem to have a smell of dust when I vac. I have changed the bag and checked all areas where dirt collects and nothing is plugged. Seems to be puffing out from bottom and behind the unit

Orecks do have a lot of leaks in the airdut system of their machines. Most likely the smell however, is coming from the outer bag itself. That get so coated with fine dust that eventually it will start to smell like dust. Only by replacing the out ... Oreck XL Ultra Bagged Upright Vacuum

I am having problems with the roller on my Oreck DTX-1300. It turns on and off intermittantly while I'm vacuuming. I have completly taken it apart and cleaned and inspected the roller unit.(I am very much mechanically inclined) This has stumped me, I have checked the electrical from the vacuum to the floor unit, and everything else that I could think of. Question: what does the metal sensore plate on the bottom of the roller unit do?? Anything anybody can tell me, I would greatly appreciate. Cap

... Oreck DutchTech DTX1300A Bagged Canister Vacuum

Can't remove bottom plate to change broken belt on oreck xl instashield vacuum ...i think i removed required screws

... Oreck Vacuums

I have a Kenmore quick clean model 116.36724500 and the belt popped off so we took the bottom off and put the belt back on, but now cannot get the bottom floor plate back on! Please help! :( I have no

... Vacuums

Wont re-assemble I took the bottom plate off to clean out the rotary bush and can not get the plate back on! I think it is the position of the roller but no matter which way I place it when i turn it , it flicks back into the place that means i cant put the plate back on!

Assuming you did not remove the brush roller to clean it and consequently did not reseat it, I am guessing that the bottom plate is not reinstalling as it should. On some uprights, the bottom plate hooks in at the front and is latched in place with c ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My problem is the brush on the bottom is not spinning and i think there is no suction from the bottom of the vacuum my rugs are in need of a vacuum and i 'm not sure what is going on - also nothing is going into the canister

Is there a shaft driving the brush, or is there a belt on this one? Are they intact and working properly? It could be possible that the motor isn't moving which would cause no suction or brush movement. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have 2 wahl hair clippers (homecut) I require size 6 comb and size 9 comb the model No is 441-3411 and 441/0359 has the base plate blade broken, Where can I source past and replacement base plate blade

... Vacuums

There is no power...seems like a motor problem. The bag is clean...the mouth is clean the plug us in...NOTHING! I took mouth off and manipulated/pushed in that power press area that engages the motor on the front (not the switch on the back) and NOTHING! Not sure if motor died and/or what to do now. Help. I have had this baby for 15 years.

The front safety switch must be pushed in by either the hose or head (or manually), before the on/off switch will operate. The most common reason for no power is a bad cord. Second most common is worn carbons in the motor, and third is a bad switch. ... Kirby G4 Bagged Upright Vacuum

The metal plate at the front of our X4 Extra has been damaged from nail heads on timber floors and although we have straightened it, we now need to replace it. We have ordered the part but cannot see how the plate comes off. We are reasonably practical and should be able to do it if someone can provide some guidance.

... Sebo X4 Bagged Upright Vacuum

I have a Hoover Mach 5. The beater bar will not rotate. I have taken the plate off of the bottom and sometimes it will rotate. I put the plate back on it stops. I have taken off any hair, string or anything else that may hang up the bar itself to no avail.

Replace the belts part # 38528-034 V belt and 38528-035 flat belt also inspect the belt groove on the brushroll if the new belt rides deep in the groove you will need a new brushroll. there is a tensioner for the V belt that tightens it when the hand ... Hoover Vacuums

FAN How do you replace the fan/removel of metal plate. i'm upgrading the plastic one to a metal one

Take off the bottom plate, remove the screws for the motor and fan chamber, remove motor from fan housing, remove the nut for the fan. You may have to lock down the armature if the nut is too tight. Replace fan and reinstall motor into the fan hous ... Oreck XL2600 Vacuum

Bissell spotbot: leaking the dirty water from bottom. I took the bottom plate off and there is a really crappy rubber seal. I think it is leaking from there.

I had the same issue. After some research, I determined I was missing a black "duckbill" gasket on the bottom of the dirty water collection tank.\015\012\015\012This caused reduced suction, and for the water to pool at the botom of the s ... Bissell SpotBot Robotic Wet/Dry Vacuum

Eureka Fantom Thunder 12V/older model Need instructions on how to change belt and headlights.I could only find 1 screw on the bottom plate none on top plate. Thanks N J

There are two screws on the Fantom Thunder (It was not made by Eureka though) on the back of the unit just above the rear wheels. Remove these two screws and the top cover can be removed to get to the brushroll, belt and headlights. I believe the lig ... Vacuums

I cleaned out my brush in the bottom front, cleaned out the small tubing going into the canister, and the canister itself. I also changed the filter.I snapped everything back into place, but Since then, it doesn't seem to have any suction and there seems to be a space between the canister and the bottom of the vacumm where the canister sits. At that area, you can feel air coming out when trying to vacumm and it just doesn't pick up, it seems to be just blowing stuff around.

You need to really look at it some thing is out of line you shooed not have\015\012any spaces in the top or bottom\015\012pull the canister back out and look at the pins that you lined up with the\015\012to ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Cracked On the bottom of my vacuum, the area around the belt housing is cracked. It looks as though the whole plastic bottom piece would have to be replaced just because of the crack.

I'm afraid that you will have to replace the base unit, part #62577, would sell for around $25. Once it cracks, then it is weak and will affect the brush roll and belt. ... Eureka 2996AVZ Bagless Upright Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

My dyson DC04 started to **** a dog toy up the main bit with the brushes - stopped it immediately and removed the toy but since then the suction is still ok/strong with the extension hose picking up but no suction is getting to main scetion/brush area - sounds like a pipe is disconnected from the front area - nothing obvious on the surface....HELP! Thanks in anticipation........... Julie Price

Get a different brand vacuum. Dyson's are easily the worst vacuum I've ever owned. I've tried the DC14, DC25 and DC33 they are all heavy plastic POS's made in Malaysia. I've owned every kind of vacuum under the sun. Rainbow, Kirby, Oreck, Riccar, Seb ... Vacuums

I was vacuuming today, and it was doing fine, then all of a sudden the motor kicked up a notch or two, then I heard the LOUDEST POP!!!...I turned it off, went and unplugged it, took off the top of the canister, then took the water pan to empty it, because I seen something on the bottom, as I was pouring the water out, I seen on the bottom, ALOT of, what looked like, small bands of metal...could you tell me what may have happened..??

It's possible the fan on the motor has disintgrated. If this is the case replace the motor. ... Rainbow E series Canister Wet/Dry Vacuum

I have a Bissell 7920 ProHeat and only used it 4 times and the brush on the bottom has stopped spinning and when attempting to spray solution the flow indicator doesn't spin and nothing comes out. I have looked at all of the belts and they seem fine. I have also removed and cleaned the heating unit. Still nothing. Any other ideas?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I have the bissell 7 and the hose is not **** and therefore nothing is **** although the bottom seems to work but nothing goes in the bag

The tube from the bottom where the dirt getts **** up to the bag is clogged with hair and dirt , also the belt is off or broken. ... Bissell Vacuums

I have a Bissell 2x Turbo 9300 shampooer. It won' spray from the carpet/floor position. I re-booted it and checked for blockage - nothing. I flushed the hand attachment and got it to spray some water but nothing from the carpet area.

The heater is glogged trust me. It is the size of a dollar bill with seven screws. take it apart and clean the water path also take a small drill bit to the ports of the heater. ... Vacuums

How to remove brush roller bottom plate

Make and model ?????? ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0352 seconds