Having problems with your Vacuums ?

How do I change the power flex on a PANASONIC MC-E458 1200W vacuum cleaner. I cannot remove the cover to get to the end of the flex Thanks Bryan


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I change the power flex on a PANASONIC MC-E458 1200W vacuum cleaner. I cannot remove the cover to get to the end of the flex Thanks Bryan


... Vacuums

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth


When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

My vacuum cleaner is making a loud squealing sound when I turn it on and the brush is turning. It gets louder while vacuuming the carpet. I tried to remove the bottom cover to see inside but, took out a bunch of screws and couldn't get the cover off.


... Kenmore Progressive Direct Drive 30912 Vacuum

Unable to remove round filter in bottom due to bolt not secure inside vacuum and it is just spinning so I can't remove nut holding on filter, but cannot see how to remove top of vacuum to get at other end of nut.


If you are talking about the acorn nut that secures the separator to the motor shaft, it can be removed with a small (or even a big, for that matter) air or electric impact wrench with the proper sized socket. Find a mechanic friend who has one, make ... Rainbow E series Canister Wet/Dry Vacuum

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]


... Miele Vacuums

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.


... Sanyo Vacuums

Recently purchase SC-N500 vacuum cleaner. Worked well only the first 2 times I used it to clean up plaster dust from floor after sanding. Since then it has not worked at all well wiht very poor suction. Fluff gets stuck in the hose and has to be manually removed. Suction power is very poor. I have washed the filter to remove the dust with no difference. Who do I contact in Brisbane to service or assess the problem further.


... Sanyo Vacuums

I am trying to take my philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag was not put in correctly. I have removed all visible screws but cannot for the life of me find how the wheel end comes apart. any tips?


Generic problem for all Vacuums\015\012I am trying to take\015\012I am trying to take my Philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag ... Vacuums

I've had my Dyson DC14 vacuum cleaner now for approximately 9 months and been very happy with my purchase. However, It is used sparingly maybe twice a week at the very most. The problem is when I try to use the item on my carpet, you have to push really hard to get it to move. It's as though the suction power is far to strong. It certainly doesn't glide as I think it should. It still picks up as usual but I cannot imagine that having to 'force' the machine to move is the normal operating procedu


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Hi I have a ws big power vacuum cleaner but have lost the user manual and cannot remember how to work it for cleaning my carpet, can you tell me where I can get the user manual


... Vacuums

I have an older Kenmore vacuum cleaner - Model #3285590C, Serial #DG4117817. I can't seem to figure out how to get the motor cover off. 2 bolts in the front have been removed but the back has no visible bindings. It seems to be held from inside the compartment! Whats the catch here!


... Kenmore Vacuums

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.


The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

How do I remove the collar to replace the cord to the power bar, I have the part, cannot get the little collar off to connect the new wire, purple to white and white to black... cannot get the old wir


... Hoover Powermax S3530 Bagged Canister Vacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u


Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

I just purchased a Sebo Airbelt D canister vacuum. I plugged it in and used it for ten seconds then turned it off, retracted the power cord and now cannot get the power cord out of the machine. Did I not spend enough money to get a quality product? Does anyone have any idea how to get the power cord out without breaking the machine?


... Vacuums

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.


Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Electrolux 5500 The cord on my vacuum cleaner won't retrack. What is the trick to get the back end off the vacuum cleaner? It looks like it was pulled out too far.


Depends on which model you have, but most of them you take off the center section, then you cab get to the 2 screws on top , and there is a screw on the bottom, then the back end will pull off. But I wouldn't try taking the cord reel apart, if that ... Electrolux Lux 5500 Canister Vacuum

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

Hot cord the cord on my vacuum cleaner has been getting very hot the heat is from one end to the other incuding the plug and also where the cord exits the back of the canister please help I love this vacuum cleaner it has been faithful to me for over 15 years!


Likely after all these years that the motor is starting to go bad and draw more amps thasn it should. a new motor at a vac dealer is your best bet. it was likely made by panasonic, so a new panasonic is your best bet, and less $$$than the kenmore for ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Power Switch How do I get the power switch out to replace it? I have a D4C model. Rainbow/Rexair. Is there a place where I can get a parts breakdown of the vacuum cleaner? Steve


This is not that hard:1. - remove gasket (it is glued so you may end up damaging it)2. - remove 4 screws holding baffle 3. - under it yo ... Rainbow E series Canister Wet/Dry Vacuum

Hello, My mom has given me her Bissell carpet cleaner. (It is NOT a vacuum.) She has lost the manual!!!! Could you get me one? It is a Bissell Power Steamer Pro, Model 1697 Also at the bottom of the cleaner it says "Dirtlifter Power Brush".


Here is a link to the manual at Bissel's site:http://www.bissell.com/images/UserGuides/1697_908.pdf ... Vacuums

My bissell 3595-2 vacuum cleaner started turning off the power automatically. Now I can not get it to turn on. This vacuum cleaner is still in real good condition, as I have hardly used it. Please advise what could be wrong. I was thinking maybe a loose connection with the on-off switc.


... Bissell Vacuums

I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!


... Miele S7210 Bagged Upright Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .


Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1603 seconds