Having problems with your Vacuums ?

I'm installing a new ignition module on a bc24w weedeater trimmer--the part has 2 screws holding it on-it is apparently adjustable--what gap setting should I use between it and the magnet (armature & rotor??) Also what is proper spark plug gap? Thanks


Answers :

I usually use a match book cover between it and the magnet. this way the gap is about right and it will not hang on the magnets. put through both sides at once, then push it in and tighten it up. then take out guage. spark plug gap is .025, the armature gap on most small engines is .010,
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I'm installing a new ignition module on a bc24w weedeater trimmer--the part has 2 screws holding it on-it is apparently adjustable--what gap setting should I use between it and the magnet (armature & rotor??) Also what is proper spark plug gap? Thanks


I usually use a match book cover between it and the magnet. this way the gap is about right and it will not hang on the magnets. put through both sides at once, then push it in and tighten it up. then take out guage. spark plug gap is .025, the armat ... Vacuums

This was my grandmothers machine and when she passed there was no owners manual so I am not sure how to use the settings on it or oil it properly. I so want to use it cause it was hers but don't want to mess up the machine. She never even got a chance to use it before she passed away. I just have no owners manual. I know how to use sewing machines but this one is older and I don't want to mess it up. this was passed down to me. and a manual would help in so many ways. even if it was sent in a


May I get the manke and model # so I can help you more ... Vacuums

The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug


... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

I have only used this mop a few times because everytime I go to plug it in the outlet, there are sparks. I have tried three different outlets. Is there a recall on this??


Hi,No, but hopefully you are in warranty...1 year...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

I am looking to write the company to let them know that my shark steam mop caught on fire. The plug sparked not to mention that the handle had broken off, too. I would like to write the company but I do not have the proper address


I think their customer service # is .. 800 798 7395 \015\012\015\012I could not find an address ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My Roomba Discovery (4210) that I purchased used seems to have charging trouble. I have tried setting it on the dock and directly plugging it in but the indicator light around the battery is blinking red then pulsating more slowly still red and repeating.


... iRobot Roomba 4210 Bagless Robotic Vacuum

Can I use a regular 2 conductor cord set on a ceiling track lighting kit and plug it into the wall? I Dont have a box in the ceiling


Yes, but make sure to use a polarized male plug ( the one with the slightly larger prong on one side). ... Hampton Bay Vacuums

I have a shark iron model G1495N It has a cut in the wire inside the rubber hosing that goes around the cord from the base of the iron When using it yesterday I didn't see the cut and it sparked after plugging it in and heating up Is not usable at all What can I do to repair it if at all? I've had it since sept 2008 Thnxs


It's probably best to replace the device, when dealing with sparks and exposed wires. \015\012\015\012If you're electrically-inclined, feel free to pry it apart (when unplugged!) and see if you can re-attach things, but generally soldering or g ... Vacuums

Does anyone know the correct spark plug gap setting for a Sears/Craftsman blower/vac, mdl 358.797342 25 cc motor


030. ... Vacuums

My kirby is shorting out when i plug it in and turn it on it wont turn on and then after a little bit it will turnon but twhen you move it it will turn back off.. and there were sparks from the cord.... i was wondering if i still have a warrant to get another one ive never had a problem with my kirby i love it but am dissapointed that i cant use it


... Kirby G5 Bagged Upright Vacuum

Can you advise which setting should be used on different floors, ie hard floors and carpets, theres 2 different settings and I don't know which setting should be used on the different floors


Turn the machine on and look at the bottom. Turn to the two settings. The setting that stops the platten wheel from moving is for hard wood floors. If you cant tell, then setting 1 is most likely for carpets and 2 is for hard wood floors. Your ma ... Hoover Vacuums

My Dyson has suddenly starting making this LOUD, horrible sound when I am using it on the carpet setting. However, when I use it on the floor setting, I do not get this noise. Also, I think the 'sucking' power is not as strong.


You need to check the beater bar on the bottom and the hose from the beater to the canister. You may have something stuck in the beater system. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Ryobi 720r wont start. Absolutely no response at choke + engage lever. I checked the spark plug but no luck. Just test i put little gas in the spark plug chamber. It started only to burn what was in the chamber then stopped.


... Vacuums

I have a Kenmore upright progrssive intell clean. For some reason it isn't sucking when I use it to vacuum. When I use attachments they work fine, but when I plug the hose back in after using the attachments and turn it back on it makes a weird noise and I can feel air blowing out of the back. Can you help me resolve this problem?


Open this manual to page 18 and clean all the filters listed to restore air flow.http://www.managemylife.com/mmh/lis_pdf/OWNM/L0908343.pdf ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

When I set my sunbeam 3331-33 coffee machine to just brew, I can hear a click but it doesn't **** up the water to brew. I have not tried the grind and brew position to see if it will brew... any suggestions on what I can do? Everything is in properly (the lid is closed properly, the carafe is on properly)... Thanks.


... Sunbeam Vacuums

I just bought kaz model K76P (M) humidifier in Kyoto. I filled it to the right water level (a bit below) and plugged it in (nothing else is plugged in at that socket). The light comes on, but the water doesn't heat up. I can't read Japanese so can't read the instruction manual but it seems a simple procedure: fill with water, set the heating thing the water, plug in. Am I missing something or is the humidifier defect?


Take it back to the shop it should work and even though its in japanese ,they will know if your doing it wrong ,but i think it may have a damaged heater or a wire off where its been in transit ... Vacuums

My TDK Clock Radio for iPhone & iPod (ADS-6P) freezes when I use the power button for the radio feature or try to set the alarm using the radio. Also using the ipod or iphone dock doesn't work. I have no idea what has caused the issue. Turning it off and on again doesn't help - it is still completely frozen and unresponsive to buttons pushed on the applicance one it has frozen. Can you help? I was given this item as a gift so I do not have the reciept.


... Vacuums

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?


This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......


Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

LlllSteam vac ws working very well--shilfted to using hand vac on furniture--when I shiftead back to wanting to use the floor vacuum using the 6 brushes and the floor vac system, the r6 rotaty brushes will not turn or function. What do IO havae to do to get them to turn and function? The lever on the side ils set for carpet terrain. What do I do now to get brushed to turn and scrub as they should and did previously. James Yerges 1'630-232-2798 JMYerges&comcast.net


What is the exact model number of that unit. There are several with that name. The only things that it could be are the handle mechanism that activates the brushes or the indicator is not working nad the level that selects the brushes is not working. ... Hoover Vacuums

Bissell will spray water when set to water rinse, but as soon as it is set to light, normal, or heavy cleaning, there is no spray. I have tried priming but to no avail. I put plain water in the solution tank to test without ay success. It is like it loses it's prime whenever you try to use a solution mix. Once you set it back to water rinse only and go through the priming steps, it is OK. Any help would be appreciated. Thanks.


Please check the following with liquid in both tanks.\012 \012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\012- Check for ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Polti Vaporetto household steam cleaner that I bought 16 years ago. I haven't used it for about 10 years because the connection between the steam er and the attachments doesn't work properly and it is difficult to use. The shop where I bought it no longer sells them and can't get them fixed anymore. I'm about to ditch it, but thought I would have another go at using it. (It was very expensive). Now I can't get the safety cap off so I can't fill it or test it. Any ideas on what I can do


... Polti Eco Pro 3000 Canister Steam Vacuum

I had used Dyson DC08 to **** out a wet car carpet. A few days later when using the V/C, there was a burning smell. Subsequently I washed the flexible hose, changed the pre-filter and post filter , but I wrongly put the pre-filter in the spot for the post filter. When the V/C was next used, there was again a burning smell and sparks. The filters were switched, but the V/C would not re-start. What shall I do?


Hi there,We'd strongly recommend against using your Dyson to pick up water. If you haven't already got in contact with us directly, I'd encourage you to do so. One of our experts will be happy to recommend the best course of action. You c ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I have a Kenmore upright progrssive intell clean. For some reason it isn't sucking when I use it to vacuum. When I use attachments they work fine, but when I plug the hose back in after using the attachments and turn it back on it makes a weird noise and I can feel air blowing out of the back. Can you help me resolve this problem?


You have the answer and just don't know it. You are there so keep looking. Somewhere between where the suction hose connects with the lower hose and the power-head. There is a blockage, you may need to turn the unit upside down and look there or try ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0721 seconds