Having problems with your Vacuums ?

Sharp microwave carousel R330J 1100 watt. When the heating cycle is started the microwave light flickers on and off and there is a clicking sound. Initially high voltage fuse blown. replaced fuse and diode, checked capacitor. Fault still present even after disconnecting power to magnetron.

Answers :

Hi and welcome to FixYa. I am Kelly.
\0121st the model number appears to be incomplete. Not an issue at this point but will be if you need parts.
\012You most likely have an interlock problem with one of the 2 door switches or the door interlock mechanism is broken.
\012There are 3 safety interlock micro switches activated by the door. One for the light, one for the Magnetron and one for the control panel power. If the problem persists with the Magnetron disconnected. The Magnetron safety interlock micro switch is supposed to blow the fuse if the unit is energized with the door open. Check continuity of your door interlocks. Pat particular attention to the NC (normally closed), C (Common) and NO (Normally Open) contacts.
\012NC should read to C and when the switch is activated read open at which time the NO contact will read to C.
\012I really suspect a bad microswitch.
\012Thanks for choosing FixYa.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sharp microwave carousel R330J 1100 watt. When the heating cycle is started the microwave light flickers on and off and there is a clicking sound. Initially high voltage fuse blown. replaced fuse and diode, checked capacitor. Fault still present even after disconnecting power to magnetron.

Hi and welcome to FixYa. I am Kelly. \012\0121st the model number appears to be incomplete. Not an issue at this point but will be if you need parts. \012\012You most likely have an interlock problem with one of the 2 door s ... Vacuums

Dc15 fuse The roller brushes on my dc15 stopped working..I checked the obvious and then noticed that the 2 amp fuse was blown on the circuit board . I've replaced it with the same type bought from Maplins but it keeps blowing .. I tested the yellow an blue wires leading from the circuit board to the roller brush head and the are in tact and I can run a current through them ... Any thoughts from anyone .? Your help would be. Appreciated thanks Lee

Hi Lee,I'm sorry to hear you're having difficulty with your DC15. If you'd like some help, please give us a call on 0800 298 0298 - we may be able to resolve the issue with some troubleshooting over the phone.Best wishes,Jack ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

The microwave will not turn on. No power. Checked fuse box and power outlet...not the problem. Unit just wont turn on? Is there a reset button or another option.?

Remove the cover and locate the internal fuse you will find near the power cord entry. Replace with the same. ... Vacuums

No power to sensor SR 12. I also have cleaned rollers and filters and bags. I have reset the handle. When I hit the power the check brush and full bag lights flash once. That is the only power that is getting through.The unit was in storage for a bit and got wet but its been drying off for a couple months. Is there something I can check or replace. Its a great Vac.

... Windsor SR12 Sensor Bagged Upright Vacuum

I have a Hoover U3330 001 upright vacuum, while using it today the power suddenly cut out and it stopped working. I have replaced the fuse with a new and tested fuse, but the machine will still not power up. please can you help?

... Hoover Vacuums

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i

At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

My Kenmore Intuition Canister vacuum has no power. Is there a fuse that could be blown out?

... Kenmore Intuition Canister Vacuum Cleaner, Blue

Does the trivac 1100 have a fuse? My machine has suddenly stopped.I have checked the fuses in the plugs and also made sure that power is at the wall socket. I can see what loks like a fuse holder in the top of the machine near to the on/off switch but it is very tight so I want to be sure that it is a fuse before unscewing it. Thank you Jim

... Philips Vacuums

The 10 amp thermal fuse on my Panasonic MC-E468 vacuum cleaner has blown. Unfortunately the red ink has worn off exactly where the temperature rating is printed so even with a magnifying glass cannot make out the exact replacement fuse to buy. Can anyone shed any light. I know you can buy the complete thermal fuse and wiring from currys partmaster but with delivery would cost about 20 pounds as opposed to 69 pence for the fuse itself. Thanks Mark Roberts

It appears the fuse is not available separately. Standard retail price for the complete unit is £9.00 including VAT. We can supply at that price plus postage and packing at cost, which would probably be no more than £2.50.  If this i ... Vacuums

My Discovery 4210 Roomba will run normally for about 20 minutes on a smooth, wooden floor. It then begins the following sequence: run forward a few inches, turn in a tight counter-clockwise circle a few revolutions, stop, power off a few seconds, power up, repeat cycle from forward run. The sequence can be repeated seemingly endlessly if I don't turn off the power manually. I've replaced the motor, and led revolution sensor system on the left drive wheel. I've blown the dust out of everywhere. A

This robot vacuum has a electronic micro processor that controls the unit and tells it how to operate and where to go based on programmed parameters. It's quite a technical marvel. I have dropped a link here for contacting the company tech support li ... iRobot Roomba 560 Robotic Vacuum

No power unable to manually turn off power, i opened up rear handle hatch to inspect the mechanism/linkage. The red on/off button seems locked in the on position. I replaced the hatch and now i have no power at all. what happened? Is there a fuse?

This vacuum has a recall notice on it. It has to do with the switch. You might want to check... They will fix it for free ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have cd mix 2, i lost the power cord, and i used a different 12v cord. The mixer played for a while then the power went off. I checked the fuse at the power supply it has continuity.

May be you unintentionally provided more voltage or current to the appliance and it has got damaged because i feel that if it played at first and then stopped then it might have got damaged due to overvoltage or excess of current .I would highly reco ... Vacuums

My dc 05 isnt working and i cant understand why , i have cleaned all filters etc and i also changed the fuse on the plug , which after i didi that it attempted to start but then jus cut out again so i thought the fuse had blown again , so i checked the fuse but its working fine could there still be a blockage somewhere in it or is it something electrical which means my dyson has to go to the dump :(

Most common cause of this problem is a wire broken inside the flex, usually either just where it leaves the plug (easy to fix) or at the other end (more of a problem). In either case, this is no reason to dump the machine - it can be fixed at a fract ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

My microwave isn't heating, but the timer and light is going. Should I go buy another microwave? Or can I replace a fuse or something? I have an emerson mw8119sbm

Did you get a response or find any answers for this? I am having the same exact issue and would rather not replace it if I dont have to...thanks ... Vacuums

My vacuum died. It won't turn on. It is not the outlet. Is it a blown fuse? How do I replace the fuse? Where does it go? This vacuum is a little over 2 years old. My older Hoover WindTunnel STILL works and has never had this problem.

It's probably the power switch. My switch was dicey for a couple years, finally gave out. Easy to replace.\015\012\015\012Remove the two screws just above the WARNING on the rear of the upper handle assembly, then slide the whole assemb ... Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum

Plugged my Dyson in this morning, switched it on and power came on for not even a second and died. No power what so ever to dyson - checked my house sockets, changed fuse. Still not working - dead as a door mouse. What could it be? Many thanks Sam

It is either your power cable, cable rewind mechanism or your motor. \012\012Try switching it on, and wiggling the lead near the plug and see if it fires up. If it does, remove the moulded plug and fit a standard plug. \012\012If not, lik ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

The power nozzle on my c141b model aerus electrolux canister vaccum no longer turns on. It was working when a large stringy object was sucked in. When hitting the red reset button, nothing happens. Is it likely that it is the fuse that needs to be replaced? All wires appear intact (I replaced the elbow assembly a few months ago.), and the sweeper moves freely.

It's not a fuse.\015\012Turn the power nozzle on it's top. Try to rotate the brush. If it won't spin, there's till something holding it. Remove all strings, threads, and whatnot from the roller. Try to rotate it again. If it still won't sp ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

I have 2003 Coleman Westlake Pop Up Camper. I have electrical problem. Replace circuit breaker and ground fault. Went camping, everything running fine the all of the sudden all power cuts off. Breaker did not trip, ground fault is fine. What could be the problem ? Is my converter bad ??

... Vacuums

Eureka Boss Smart Vac 4870 evidentally overheated. Allowed unit to cool and observed a spark/smoke at outlet when it was replugged into the power outlet. Unit will not power up now. Circuit breakers in the home are fine. Is there a fuse that can be replaced in the unit? Does the unit need to be serviced? Is there a Eureka Authorized Service Center in Orlando, Florida?

Seems Eureka is putting faulty, insufficient wiring in many models, most especially my model (if you do a search of this site, you will be how many people have experienced fried wires and switches). There should be a class-action lawsuit in my opini ... Vacuums

My power head to my rainbow does not pick up as well as it always has. I've checked for blockages - none found. Checked the belt on the bar and replaced it just in case...any suggestions?

Clean or replace the separator under the main motor. Brushroll may be worn and needs to be replaced. Make sure the bottom plate is on correctly by catching the tabs on the front of the head and then fastening. ... Vacuums

My Dyson DC14 Blitz It will not switch on. I have checked the fuse in the plug and it is fine. I have also vreified that the switch is working by using a multimeter. I'm guesing that there is an internal fuse blown (or worse!). Any suggestions?

I ended up dismantling the Dyson in an effort to determine the problem. In doing so I discovered that if I rotated the motor backwards by a quarter of a turn, it came back to life. Rather odd really. The Dyson is working fine now, and event benefi ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

No power Our dyson DC07 was working fine, then we pushed the button to turn it on. It started to run then shut off and now it is like the power is no longer there. I have checked outlets and they all work. Is there a fuse of some kind in this unit?? If so, how would I get to it?

The motor will have a thermal cut out,however chech your plug fuse and the cable as it enters into the off on switch. its known to snap here within insulation..... ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Bissell Upright Proheat 2x and the dual power brushes wont rotate. I went to replace the drive belt and noticed the drive shaft does not turn when power is turned on. What shall I check next?

Is there a light that comes on when you "turn the power on." If there is no light, and the unit is plugged in, how do you know there is current going to the motor? Sounds like there might be a break in the cord. Examine the cord near the plug end ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bissell power trak just stopped working i turned it off and a few hours later i turned it on again and it will not work. I switched over to an outlet i know works and it still didn't work I checked the outlet after and there's still power there. Is there an internal fuse?

... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0862 seconds