Having problems with your Vacuums ?

How to fix a garbage disposal - Vacuums

Answers :

Depends on what is wrong with it.\015\012Two basic problems that can exist -\015\012Circuit breaker can be tripped\015\012Blades can be caught up.\015\012
\015\012Unplug unit and re-set breaker on bottom of unit.\015\012Get an appropriate size allen wrench and insert into bottom of unit and manually turn chopper blades.\015\012Remove allen wrench, plug in and start unit up.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to fix a garbage disposal - Vacuums

Depends on what is wrong with it.\015\012Two basic problems that can exist -\015\012Circuit breaker can be tripped\015\012Blades can be caught up.\015\012\015\012Unplug unit and re-set breaker on bottom of unit.\015\012Get an appropriate size a ... Vacuums

I have ajenair garbage disposal under the sink and it leaks when running. What's the fix?

First inspect that all connections to drain and seal to sink are tight. If it's leaking through the housing itself, it needs to be replaced. Be VERY CAREFUL... you have house current and water in close proximity and can possibly get severe electrical ... Vacuums


Taking apart a garbage disposal is a fairly simple process that you can complete in less than a half hour. Occasionally you will find that your garbage disposal has worn out or stopped working and needs to be replaced. The disposal is attached to the ... Vacuums

My hoover Wind Tunnel vacuum cleaner's motor spindle keeps overheating. Because of the high temperature, it keeps burning through belts (the big, wide ones). I have taken it in to the vacuum repair shop about three times now, and the problem has never been fixed. Does anyone have any advice on how to fix this or should I just buy a new vacuum?

... Vacuums

My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed? thanks

Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track. ... Hoover Vacuums

Clogged vacuum Rather stupidly, my boyfriend 1) were vacuuming without a bag and 2) vacuumed up a big piece of cotton from a sofa cushion. And now it's making a horrible noise and I see it vibrating where the tube connects to the machine. When you look inside there's a white thing sticking out but it looks like it's part of the vacuum. If it's a clog, how do you fix it? I tried unscrewing the tray the bag sits in but it won't budge.

You can start by taking off the bottom plate or top cover, which ever comes off, that is where the inlet starts going in and hopefully the clog is there. Could be in the hose also. But without the complete model number I can't look it up to see a p ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

I have the Miele S175i Powerhouse Plus and it vacuums fine, but the bottom piece of the vacuum is broken. The head of the vacuum swivels freely and doesn't lock into place. Also, the connecting belt is messed up. How can I fix the head so that it doesn't swivel freely?

... Miele S175i Bagged Upright Vacuum

My Kenmore Handi-Mate Jr., Model # 116.36622501 generates a burning smell once i turn it on. It is out of warranty. There is any way i can look at the vacuum myself and figure out what is broken/burned and understand if it is worth fixing it? It vacuumed very nicely for about 2 years and it wasn't a cheap vacuum. Thank you very very much.

... Kenmore Vacuums

The vacuum does not **** in dirt. It is blowing air instead. Yet when I disconnect the vacuum from the cannister, the suction seems very strong. I took it to a vacuum repairman, and he said that Kenmore sucks and I might as well get rid of it. (He wanted to sell me another one) It is 10 years old, but if I can fix it I would like to try.

... Kenmore 22613 Bagged Canister Vacuum

No vacuum My Floormate has plenty of air moving, but no vacuum at the nozzle. When I turn it on, the filter hops up to the black rubber "intake", rather than staying in its spot. It seems to me that the intake should be in contact with the filter when the reservoir is installed. And I don't understand why the intake isn't closer to it, but it seems fixed there, almost an inch higher than the filter. When I remove the bottom reservoir and turn the h3000 on, I feel vacuum at the intake, and air

Someone must have lost the filter cover from the machine. It is a clear blue plastic cover that goes over the filter and has a hole that lines up with the motor intake. It is approx. 3 inches square and has an angular top to coincide with the motor i ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.

When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I have a Craftsman wet dry vac with blower capability (22 L). While I was using it to **** up water, the water came out of the blower hose. Now I can't get it to work as a vacuum. What can I do to fix this problem? Is there a toggle switch somewhere that allows me to choose vacuum or blower? Also, will the vacuum still work without the filter nut attached to the plate? Please let me know at your earliest convenience. Thank you.

... Craftsman Vacuums

DT 1300 As I am vacuuming the motor seems to fade in and out and sometimes stops running for a few seconds and then resumes. If I move the hose a bit near the vacuum end, it runs smoothly again. Does this sounds as if there might be a short in the motor? Would this be something I can fix myself or does the vacuum need to go in for repairs.

... Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum

We have a Kenmore Progressive Model 116 Upright bagged vacuum with Hepa filter. It's at least a couple years old. For quite some time now when ever we use the vacuum the vacuum motor will shut off nafter about 5 min. of use. We then need to let it sit for awhile and then we can run it again for another 5 min. The bag has been change. Any one have any ideas how to fix this?

I suspect that you have a restriction. The motor sounds like the thermal break is stopping the motor before damage, due to heat.\012You must witness that the entire suction and discharge side are clear. This is not always very easy, but necessa ... Kenmore 34612 Bagged Upright Vacuum

My electrolux epic series 6000 sr vacuum is not working. I was vacuuming when it shut off and the bag light came on. After changing the bag I tried turning it on and the question mark light comes on instead of the vacuum. What does this mean? How can I fix this?

... Vacuums

My hoover windtunnel vacuum keeps retracting the cord while i vacuum. How can i fix this?

... Hoover Vacuums

My powerhead on my EXL Tri-Star goes on then shuts off. When youturn it upside downit runs, then back on the floor it stops. Is it the belt inside the powerhead and if so to I take the head apart and replace this belt. Can any vacuum repair place fix this if I have the part. Vacuum was purchased in March 2000 Thank you, Dianne Miller [email protected]

A vac shop is probably going to require you to use their parts for warranty purposes. but its pretty simple. most shops should be capable to do it. ... Vacuums

Carpet vacuum attachment quit working after sucking up a bedskirt. Bedskirt has been removed but carpet attachment will not work. My old vacuum had a reset button on the carpet attachment for use when the carpet attachment sucked up something and turned off. Does the Hoover have such a feature, and, if so, where is it? If not, how do I fix the problem and how do I keep it from recurring? Model # S3765-040. Serial # 100700081298. Purchased 2/08.

I have a Hoover Conquest approx. 4 yrs old. The turbo head is not working Model No. PB4 230-240V AC 50Hz 200w CS4901N (N127) I have been trying to locate another one or another one similiar to fit my machine ... Hoover Vacuums

My Generation 3 Kirby Vacuum is giving off a burnt rubber smell when I vacuum. I have tried to raise the height of the head but it still happens. Can you tell me what could be causing rubber to burn? What needs to be fixed?

The belt driving the brush roller in the power head is slipping. It is really just a big thick rubber band. Where it wears out it slips and burns due to friction. Look at the bottom of the power head. There is a cover plate held with 2 to ... Kirby Generation 3 Bagged Upright Vacuum

Hello there, I have Bissell Vaccum Model 6579 3...and it's not picking up the garbage..it works but nothing in going in the garbage container. Can you tell me how i can fix it.

I have the same problem!!!! ... Bissell Vacuums

I was vacuuming and pulled the cord too far. Instead of the plug pulling out of the wall, it pulled at the vacuum. Can this be fixed economically?

You should be able to reconnect it yourself. remember to maintain original polarity. if the inside of the wire has no colors denoting hot and neutral. look at the outside of the wire for a smooth texture and a texture of ridges the smooth texture cor ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Dyson brush won't stay flat on carpet...I need to have the vacuum almost upright for contact to be made to vacuum...this is a problem ...simple fix?

... Dyson DC07 Bagless Upright Cyclonic Vacuum

I plugged in my kirby G4 and when i turned it on there was a loud popping sound and sparks came out from the back of the vacuum. Does this mean the motor blew and the vacuum is garbage now?

Oh,I would say so.Does it run at all now,or just shut off completely?If you turn it on,do you get any kind of smell? ... Kirby G4 Bagged Upright Vacuum

Smoking belt Hey I have a Eureka 2961 avz bagless vacuum, and if it's on for a few minutes i can smell the belt burning.  If the vacuum is left on any longer the belt starts smoking.  I took the case off and there was a little debris but not much.  Is there a cause and fix or just time to replace the belt?

Belt is slipping because the bearings on the beater brushes, which it turns, are jammed or full of dust. \015\012Alternatively the belt has stretched after being overheated and needs replacing because it now slips. ... Eureka 2961AVZ Bagless Upright Vacuum

My sister used my bagless Dirt Devil EnVision vacuum to clean out the last bit of ashes from her fireplace. The vacuum still runs but I do not think it is picking up. Can this be fixed?

You should just get a new vacuum. ashes are not very good for vacuums ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1063 seconds