Having problems with your Vacuums ?

I bought a used Miele vacuum with the SET210 wand, but the push button to release and clamp the telescoping wand was missing. I can get the wand to slide by pushing with my finger, but it's a little difficult. The main problem is that nothing holds it in place at the desired position. I bought a replacement push button online, but it came with no instructions. How do I install it?


Answers :

Your best bet would be to put on your friendly face, and take the unit into a Vacuum Repair Shop, and have them assist you, or at least give you tips on the procedure. Chances are you will have to disassemble the unit a lot more than you might want to. You might try to contact Miele support to inquire about any diagrams, etc., and their support site is here:
\015\012http://www.mieleusa.com/
\015\012Wish I had more ideas. Good luck, and hope this helps.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I bought a used Miele vacuum with the SET210 wand, but the push button to release and clamp the telescoping wand was missing. I can get the wand to slide by pushing with my finger, but it's a little difficult. The main problem is that nothing holds it in place at the desired position. I bought a replacement push button online, but it came with no instructions. How do I install it?


Your best bet would be to put on your friendly face, and take the unit into a Vacuum Repair Shop, and have them assist you, or at least give you tips on the procedure. Chances are you will have to disassemble the unit a lot more than you might want ... Vacuums

REMOTE CONTROL IS MALFUNCTIONING & NOT TURNING ON CUSHION - Hello. I bought a used (by near new) Shiatsu+ Massaging Cushion from Ebay. When I installed it today the remote control was faulty. When you push the Power button, the blue light comes on, but none of the other buttons work. When you push the Power button again to turn it off, it clicks & turns itself back on again. So it's running but nothing is happening in the massage cushion. I did see a card in the box saying "For the Shiatsu


Before you use this cushion you MUST first 'unlock' the rollers which are held in place by a screw which MUST be removed or the unit will self destruct. The manufacturer provides a hex wrench to remove the shipping screw and a large label on th ... Vacuums

My Error light will not go off. I just bought new batterie, as I thought that was the problem. If I hold down the power button and the play button on the vacuum it will run. When released it stops. The remote will work for the unit if I am holding down the power button on the vacuum.


... Infinuvo QQ1 CleanMate 365 Robotic Vacuum

I have a Filter Queen Majestic canister vacuum cleaner. At the end of the wand, a button to release the attachement not only broke, but also one eyehole on the wand where one nipple on the button falls into. So therefore a new button isn't going to fix the wand because there isn't a hole on one side of the area where the button falls in place for a nipple to secure the button in place. IS THERE A REPLACEMENT PART FOR A NEW SECTION OF THE WAND WHERE THE RELEASE BUTTON IS SECURED IN PLACE THAT I C


... Filter Queen Majestic Canister Vacuum

I have model RGR126 Wireless Rain Monitor. All of a sudden, it has quit registering outside temperature. I changed the battery in the outside sensor and even pushed the reset button, but nothing I have done is fixing the problem. Please help! I really miss getting the temperature outside before I get dressed for work. Thanks.


... Vacuums

The telescoping wand on my kenmore magic blue cannister vacuum stopped working shortly after I bought it a few years ago. After 10 minutes of pushing sometimes I get it to work. It gets longer easier than shorter. What could be causing this problem? Please help!


... Kenmore Magic Blue 24195 Bagged Canister Vacuum

No Power Nothing happens when I push the power button. We've taken off the covers and found that there's a circuit board. Any suggestions on how to fix this problem. Thanks C


... Miele S 4210 Bagged Canister Vacuum

I love my dyson but it suddenly won't stay powered on! I push the on/off button and it works fine but only if I hold the button down. As soon as I take my hand away, it stops. I've had it and


Probably needs a new on/off switch here is video how to do it ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

When squeezing trigger and Depressing Clean surge Button on Upper handle of the Hooover Steam Cleaner F5914-900 there is no "snap" indicating trigger rod is in place. Everything else went in as instructed. The screws and bolts were no problem this concerns me because the main complaint I read about this model was leaking from the trigger and clean surge and the problem was not getting the rod in place. No matter how many tries or people (three) it still doesn't occur.


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552215\015\012Generic problem for all Vacuums\015\012When squeezing trigger and Depressing\015\012P ... Vacuums

My Roomba 530 does not speak when I hold down the dock button. The manual says it will talk me through a demo if I hold down the dock button but it does not speak at all, ever. Any ideas what I can do? Is it faulty? I bought it 3 days ago.


If it were human, i'd say its bashful, but in this case you may need a new rom pack. Call the service dept and describe this problem in detail.iRobot Service & Support\012Find answers to frequently asked questions. Need further help? Please ... iRobot Roomba 530 Robotic Vacuum

Power Problem Whenver I push the power button on the handle the vacuum stays on for a few seconds then turns off. I have to push the button on the handle all the time to keep the vacuum working.


Hi There,\015\012\015\012Unfortunately this is being caused by static electricity building up in the electronic controls in the handle of the hose. I've seen this problem on numerious occasions, and in fact I have the twin brother of t ... Miele Blue Moon Bagged Canister Vacuum

When connecting the wand into the brush component. sporatic power (sometimes runs sometime nothing) the power is on again off again. when hold pressure down on the wand the power stays on. do you think the coupling connection is bad on the wand? would the wand replacement likely be the culprit?


There is is switch or sensor in the connection. Likely that piece is worn or shorted out. You may be better off getting a new wand piece ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

My vacuum is a Kenmore Special Edition with a Power-Mate 12.0 AMPS wand. I ran over the edge of fringed edge of my living room carpet and immediately turned off the vacuum. Although I have removed the fringe pieces from the wand head and I have pushed the overload protector reset button on the wand, the wand brush will not turn. Help- it's the Thanksgiving weekend and guests are coming soon! Thank you.


... Kenmore 25512/ 25513 Progressive Canister Vacuum

The hose does not stay connected to the wand although the collar appears to be locked in place for a while. Is there a replacement part for this? Also the holder where the wand goes in has split horizontally. This appears to be one piece with the body of the unit. Is it repairable? It still holds the wand but continues to get worse.


... Dyson DC07 Bagless Upright Cyclonic Vacuum

The beater bar motor doenst work when i push the bar button the bar button doesnt light up like power button how can i test bar motor or bar switch or what is the common problem wiyh this model I have 2 that dont work the same way


If it do not work ...and you already are on the second one that behaved in the same way it may be a problem with the power in your place and the cause it may be the main fuse...Im not sure where is located in this model but it has to be near the powe ... Vacuums

I have the Oreck Sanapathic DMS2000 Handheld Steam Vacuum, but no steam comes out when I push the button. I hear the motor, is there any buttons I am missing or any help on how to make it work, been plugged in for 5 min now. Held button down for 2... nothing. Just a drip of water.


ORECK DMS2000 No Steam First, tested tank and filter flow together using suction via plastic tubing. Worked freely Second, removed pump and disconnected hoses and terminals [watch location,three terminals on pump, two plugs] ... Oreck Sanapathic DMS2000 Handheld Steam Vacuum

The wand release button has broken. Therefore, the wand does not lock into place which results in swivelling of the handle and sometimes the handle coming off while using the vacuum cleaner. Can this wand release be readily repaired?


... Euro-Pro NV31 Infinity Vacuum

My roomba wont work. Pushing the power button doesnt do anything. It charges seemingly normal, going to green in a few hours. ive tried the reset trick, holding the power button down with the battery removed. Now what? thanks


... iRobot Remanufactured Roomba Vacuum Cleaning Robot with Scheduler, Case/Color May Vary Robotic Vacuum

I have singer fashion maker 2818. The problem is the bobin casing (the one which holds the bobin)is coming out (i.e) loose. trying to fix it in place but not sucessful. can someone explain how to open and fix the case and place the other supporting covering so that there is smooth motion of the needle and the bobin.


... Singer Vacuums

I just bought a Hoover Platinum Collection MaxExtract Carpet Cleaner (Model No. F8100900). This is the first time I've used it and got half way through one room and the unit cut off and has no power at all. No lights anywhere. On/Off button is inoperable. I checked the outlet and it's still operating so it's not a circuit breaker issue. The problem appears to be with the machine. Has anyone heard of this happening this quickly? Is there a reset button on the machine>


... Hoover Vacuums

The extension wand is stuck. It will go up to a certain point and stop. The gray flexible hose that it is housed in is not damaged and there is nothing on the steel metal rod that slips into the hose that I can see. The gray button on the handle still depresses as well and everything is still "Clicking" as far as the button. thank you


I would try the dyson medic .com this is the place that specializes in the dyson vacuum. Good luck ... Dyson DC25 All Floors Bagless Upright Vacuum

My Charmglow Electric heater is not working. The problem is when i turn on all the buttons which includes blower fan, heat 1,heat 2, and firebackround motion. Only the fire backround motion goes on nothing else. I did notice that the fan button is not working properly


... Vacuums

When I plugged in my Riccar Vacuum cleaner - it made a pop sound. The breaker had not been moved - there was no smoke or apparent damage. I tried to depress the restart button and nothing happens. Is there a technique about pushing the restart button. Please advise.


Check the cord where it goes into the machine on back. most likely blew out at machine ... Riccar 8955 Upright Vacuum

Chatter We have a Kirby Ultimate G. Since we purchased it it bounces across the floor and the level of the sweeper has nothing to do with it. To get it to stop, it has to be at the highest level. The place we bought it, has done nothing to help us. We tried a new beater brush, no help. If I have to use it at it's highest level to sweep my carpet, I might as well not waste my time. ANy suggestions?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=11557&thid=576381\015\012Chatter\015\012Posted by CANRN on May 06, 2008\015\012We have a Kirby Ultimate G. Since we purcha ... Kirby Ultimate G Bagged Upright Vacuum

Pfaff 2140 Getting an error code that reads: error in read parameters, and if this error occurs several times contact your dealer. -then you have to hold a crosshair on the screen push the scissor trim button and reverse button to get back to the main menu. I just had it in for service a month or so ago...?so there should not be any major issues, what does this error code refer to?


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0904 seconds