Having problems with your Vacuums ?
How do you thread the bobbin on a Necchi 534FB sewing machine?
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How do you thread the bobbin on a Necchi 534FB sewing machine?
I have a Necchi Sewing Machine Model #523 (40 years old). It operates well except for the following problem: the bobbin-winder spindle does not wind, and thus nable to fill the bobbin flange with thread. Thank you.
Our beautiful Bernina 730 sewing machine has been stored in the garage in its original case, and that wrapped in plastic, for a few years now. Temperatures have been both hot and cold in the garage, but the environment was dust-free. We have brought the Bernina in, set it up, oiled it as specified in the manual, with the original sewing machine oil. We have correctly threaded the machine and the bobbin thread is up. When we press on the pedal to sew, the machine gets electricity and buzzes
Hello and thank you for using Fixya ....From what you describe there can be only 2 causes...Either the machine is still stuck ..and the motor buzzes cause it can not spin it ..and in this case it needs to be oiled more..and be spun by hand unt ... Vacuums
I have a Continental Electric portable sewing machine and I can't get the bobbin to thread into the machine to start sewing. How do I place the bobbin and where does the thread need to go for the need to catch it?
... Continental Vacuums
My Kenmore sewing machine timing has gotten off. I am sewing a big upholstery project and it starting bunching thread from the bobbin. The thread is so heavy that I had to put some pressure just to get it undone. This happen a few times and then I found it wasn't sewing at all. When I evaluated without the materials in place I could see the needle would catch on the white plastic piece under the bobbin and the thread would not catch on the metal arm. It appears to be off by 1/4 - 3/8 inch.
HelloDisassemble your bobbin case which is realy quite easy, clean\015\012thoroughly with a brush and air, paying particular attention to any\015\012rust that may have formed, and any thread that may have weazeled it's\015\012way into sma ... Kenmore Vacuums
I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me
Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums
While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!
Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums
Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st
Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums
I have Necchi Lydia 544, inheretade, and don't know which way the needle is fixed! what side does the flat part of the needle face? Also, what are the two bobbin holders on behind the main body of the machine, and how do they work? And, how the hairy heck! do I thread it? finally, for now! How do I get the bobbin holder to ...a...hold the bobbin, and b...make it stay in the machine, ..well, it obviously attaches in one way only, and I cannot find that way!? Thanks, Yvonne.
Hi,Here are some websites with useful information on your machine:http://www.free-guitar-tablature.com/Lydia.html This one shows how to take the bobbin case out with pictures.http://www.youtube.com/watch?v=FbEMwLNzsG4 ... Vacuums
I want to get my XL-5000 singer sewing machine to work. It does not sew. The top thread will not pick up the bobbin thread for one thing and the other problem is that it gives me a error message saying incomplete threading.
Check if there is any thread in the bottom bobbin and next remove it and give it a good clean in its surrounding area.Oil surrounding mechanism carefully and manually push the top needle in and watch the bobbin spinning a see if it tried to pick the ... Vacuums
I have a Pfaff Classic Style 2025. After clearing a thread jam in the bobbin area, the machine will not sew. It works without thread, but I think the bobbin case is crooked. The bobbin opening is off to the right, not up, as it needs to be.
I have a Singer Model #4562 sewing machine. I am having trouble adjusting the tension. Everytime I try and turn the knob to adjust the bobbin just gets looser. Right now it just snags and gets caught underneath the material and bunches up into a big ball. There is a lot of thread inside the bobbin case that came out of the bobbin and has to be cut out to free the material. How do I fix this mess. I am a novice at this. I have not sewn in several years and would like to sew a few quilts
Sewing machine won't pick up bobbin thread
Open the bobbin case and see if the hook is turning, if it is it is just a timing problem with the hook and needle, if it isn't tuning you may have a broken gear or timing belt.....It eill need to be looked at or adj by someone who repairs them....Da ... Vacuums
Janome 6600 sewing machine. bobbin thread is gumming up underneath on a swimsuit knit type material (4 layers). Brand new machine had 1 1/2 weeks. Sometimes material goes down into the bobbin area jammed by needle. What am I doing wrong?
Make sure you're using a polyester thread (I use maxilock serger thread) then a stretch needle, and hold the tails of your thread until you get started into the seam so the fabric cannot push down into the opening on the throat plate.\015\012 ... Vacuums
Cant figure out how to thread elna 1000 lotus sewing machine. also the bobbin keeps getting tangled. if you could send me a diagram on how to thread and bobbin i would appreciate it
I have a brother project runway limited edition sewing machine and there is a constant jam with the bobbin threading and I have cleaned it,removed the sewing plate and everything I can possibly think of. If the bobbin case is scratched would it cause the jam?
Hi The usual cause is that there is a problem with the upper \015\012threads, often it is not caught in the tension discs. When you thread \015\012the machine, make sure that the presser foot is raised - this causes the\015\012 te ... Vacuums
Elna Corina Sewing Machine: the bobbin thread does not pick up. Someone took out the booin case from the machine, and it was never re-installed correctly. Now the thread will not pick up.
My kenmore sewing machine (Model #385.11803) isn't picking up the bobbin thread. Bobbin thread case isn't turning. HELP!
Top thread does not pick up bobbin thread, also clicking sound when needle is down under plate, as if it is hitting something. Please help I have a job to do! This machine is new it's a Singer Inspiration Model 4228. It worked just fine until I finished my first sewing job on this machine. I'm hoping you can help me! Thank you, CD
... Singer Vacuums
Brand new Kenmore Sewing Machine model 385, 16782 It was sewing fine. But I changed to the zipper foot and now the bottom thread just makes a mess, even when I use the regular thread. Can't think what else has changed - I didnot rethread or touch the bobbin.
We have a vogue stitch janome model 539 115v sewing machine. we were trying to sew but, the thread is not picking up from the bobbin. the thread keeps breaking and we are unsure what tension setting should be used for cotton cloting. please help. thanks! tom staron
Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna
... Singer Vacuums
The last time I sewed with my Necchi the tension was fine. Today when I threaded my needle, the thread felt tight in the upper tension dial. I tried re-threading the machine several times, but it didn't help. Now the parts of the tension dial are all loose and wobbbly and I have no upper tension. Doesn't matter what the dial is set on. The tension dial appears to be broken, but I don't know how that could have happend since I store it in a case.
I found this thread (no pun intended):\015\012\015\012http://www.fixya.com/support/t2902978-need_replace_upper_tension_dial\015\012 ... Vacuums
I have inherited an old Elna Super model sewing machine to which I have no instructions. I am trying to figure out how to thread the bobbin, etc., can you give me any tips or pictures, or can you find me a manual. I believe this machine was purchased in the 1940's?
Upper thread of shark 803XC sewing machine will not pick up bobbin thread