Having problems with your Vacuums ?

How do we change a belt on a euro pre shark no bag vacuum


Answers :

Try this procedure for Euro-Pro Shark...

A.- Instructions
1. Lower handle of vacuum and flip over so that it lies flat on floor upside down.
2. Twist 3 plastic securing latches with large flathead screwdriver or a coin.
3. Remove black plastic roller brush assembly cover.

At this point, you should see the motor shaft it wraps around (it's metal and as big around as a pencil, buried fairly deep in the now exposed well, you'll also see two white plastic wheels that are part of the roller brush. One is an "idle" wheel that spins freely, and the other wheel is part of the roller brush and turning it turns the roller brush.

4. Remove the roller brush assembly by pulling upward on it. You may need to "walk" the brush assembly out one end at a time a little bit at a time.
5. Loop the new belt over the two wheels of the roller brush assembly and replace it back into the vacuum.
6. If you can manage it, stretch the belt over the end of the motor shaft, making sure the belt is running between the two prongs of the belt guide operating by the carpet/bare floors switch.

B.- If successful, perform steps 1-5 in reverse order to reassemble the vacuum. If you cannot stretch it over the motor shaft, you'll have to continue with step 7 to get a better grip and angle on the belt.

C.- Then, continue...
7. Remove two screws next to rear wheels nested deep in screw socket holes.
8. Remove 2 screws at front of corners of vacuum previously hidden by roller brush assembly cover.
9. Remove 2 screws sunk in hole sockets next to flat holes that accommodate the coin screw latches.
10. Remove 1 short screw from slightly behind roller brush in center of top assembly. (It is easily visible and you need not remove the brush assembly again to get it out with a screwdriver.)
11. Remove the 2 screws holding down the metal brackets (1 screw per bracket) that hold down the carpet adjustment wheel assembly.
12. Remove the brackets and the carpet adjustment wheel assembly.
13. Remove carpet height adjustment lever by removing the single screw buried deep in the center of the plastic height adjustment cylinder. (a hollow cylinder with ratcheted teeth spiral gently down into the well.)
14. Turn Vacuum right side up.
15. Remove blue/green top assembly that fits over the start button and "Full" light indicator.
16, Making sure belt is still looped over white plastic wheels of roller brush assembly, pull belt onto motor shaft.
17. Replace top assembly, it snaps into place.
18. Turn vacuum upside down and flat on floor.
19. Make sure belt is running between prongs of guide operated by carpet / bare floors switch.

Perform steps 1-13 in reverse order to reassemble vacuum.


Hope this helps.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do we change a belt on a euro pre shark no bag vacuum


Try this procedure for Euro-Pro Shark...A.- Instructions1. Lower handle of vacuum and flip over so that it lies flat on floor upside down.2. Twist 3 plastic securing latches with large flathead screwdriver or a coin.3. R ... Vacuums

How to change belt on shark uv210 vacuum - Euro-Pro Vacuums


... Euro-Pro Vacuums

Need an owner's manual for the Shark Roadster Euro-Pro vacuum sweeper Model UV208R in order to change the belt


... Vacuums

How i fix my euro pro vacuum shark - Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum


... Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

Eureka Bravo with new belt & bag suddenly won't start. I replaced a very worn and slack belt with a new one, vacuum then ran for maybe 20 seconds then shut off and now won't restart at all. Bag was also changed at same time. Is there a fuse, maybe? New belt too tight? Thanks


... Eureka Bravo II Bagged Upright Vacuum

Need bags for the euro pro x ep 238 - Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum


Needed bags for this vacuum and FINALLY found them at http://www.totalvac.com/parts/X10-3005.html?zmam=6843742& ... Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

Manual for Euro-Pro Shark V1725 - Euro-Pro Shark V1725 Bagged Handheld Vacuum


... Euro-Pro Shark V1725 Bagged Handheld Vacuum

How do I change the belt on a vacuum cleaner - Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum


You don't. Call cust. service, they sound send a new head. ... Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum

Shark vacuum belt - Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum


... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Need a hose for shark ep 238 canister vacuum - Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum


... Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

How do i change my vacuum bag for my shark plus vacuum


Open it and put it back in :) ... Vacuums

I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!


... Miele Vacuums

SHARK NAVIGATOR belt came off - Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum


... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

I need a belt. Where do I get one for a EURO-PRO Shark vacuum Model # UV210CN. Belt # YMH 29438-49/06


Here is the toll free customer service number for your Euro-pro shark vacuum.\015\012800-798-7398 ... Vacuums

Replacing drive belt on shark hand vac v15z - Euro-Pro Shark EP750 Bagless Handheld Vacuum


... Euro-Pro Shark EP750 Bagless Handheld Vacuum

Change belt on hoover savvy bag and bagless upright vacuum


... Hoover U8155-900 Savvy Bagged Upright Vacuum

Changing A Belt on Vacuum


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=656349\015\012Generic problem for all Vacuums\015\012Changing a Belt on Vacuum\015\012Posted by cnjk on ... Vacuums

Won't start. My son was using the vacuum & Didn't change the bag. The vacuum was making the full bag smell, but the light was't on & it didn't stop. I stopped him, changed the bag, checked the filter, closed the compartments & turned on the vacuum. Nothing happened. I checked to be sure that it was plugged in, that wasn't the problem. I've let the vacuum "rest" for several days, It still won't start. Any suggestions?


There is a reset button at the back of the powerhead. The user manual can be downloaded from the electrolux website, although I didn't find it very useful. There was some info on how to change the powerhead drive belt. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I accidently ran over a sock while vacuuming underneath my bed and the belt broke (brush does not rotate now). I've always changed the belts in my vacuum cleaners, but the Healthy Home manual states that I need to bring it into a shop so that a professional repairman can change it. I find this ridiculous and now wish that I never bought it. How do I change the belt myself? PS I have already bought a replacement belt.


... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Change belt on oreck xl intellashield - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Hoover windtunnel self-propelled vacuum is not suctioning, changed belts, new bag what is the problem and i have checked the hose.


Have you cleaned the filters? ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How to change g5 belt - Kirby G5 Bagged Upright Vacuum


1)First, you turn the square belt lifter on the front of the power nozzle until the red arrows line up (belt off) \015\0122)Remove the power head from the front of the machine. Now turn\015\012the belt lifter the other way and line the green ar ... Kirby G5 Bagged Upright Vacuum

I need a belt for my Shark Pursuit Euro-Pro X vacuum. What is the part number and where do you get one?


I am unsure of the part number, but they have them for about $5 after shipping here:http://www.totalvac.com/accessory/parts/sharkbelt.html ... Euro-Pro UV209 Upright Vacuum

Change Belt on Sebo Automatic X1 - Sebo Automatic X1 Bagged Upright Vacuum


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the FRONT of the machine. NOTE ALSO - the machine has two toothed belts, it makes sense to change both while you're at ... Sebo Automatic X1 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1260 seconds