Having problems with your Vacuums ?

I have a eureka uno widetrack and for no apparent reason the motor is racing very high. The belt is fine and everything is secure on the motor

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a eureka uno widetrack and for no apparent reason the motor is racing very high. The belt is fine and everything is secure on the motor

... Vacuums

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb

Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

I have a Euro-Pro Shark UV-204. The Vacuum turns on, motor sounds fine, and suction is as strong as ever. Still picks everything up in its path. However, the bristels on the bottom do not rotate around, the belt is not broken or loose. Is there something I'm missing?

... Euro-Pro Shark UV204SH Bagged Upright Vacuum

I have a Bissell PROheat 2X shampoo carpet cleaner and the brushes stop working. i have changed the motor and checked the belts. everything is fine. any ideas?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bissell clearview 12 amp vacuum's motor races. Belt seems to be fine.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

When i turn on my yellow Eureka upright everything works but when i flip the switch on the handal to do the carpet the brushed do not work. The belt looks fine. Is the motor dead?

The brush is worn out most likely ... Vacuums

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?

... Kenmore 34722 Grab-N-Go Upright Vacuum

My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.

Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hi, I have a Dyson DC04, (silver/lime) making ear popping screams! Does not happen all the time, and more noticeable when it is pulled back.The suctions not a problem and no funny smells or strange noises from the motor. Ive taken the base plate off and the belt and brush bar seem fine, but when I turn the belt, it seems to be the motor spindle thats squeaking, almost as if it need oiling, any help please

... Vacuums

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?

Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

My Bissell 3760-1 has stopped sucking in the roller portion. The grab n go part are working fine. Checked the belt and it looks fine. Did I burn up the motor or a microchip?

Hey Lisa! Sorry you're having difficulty with your Lift-Off vacuum. Here's a link to troubleshooting steps to assist you with the suction.\015\012http: ... Vacuums

I have two old identical 5842's that I use in the garage and around the house. The belt broke on one so I bought a bag of 2 genuine Eurika "U" belts, which is the correct belt for this vacuum. They were obviously smaller than the original belt because they were not stretched out. When I put the new belt on it lasted about 20 minutes and then came off. I put it back on and ran the vacuum with the cover off to see what was wrong. Everything looked fine except the belt rides to the outside edge of

Not 100% sure this is the remedy for that particular problem, but I would take the time to clean both of the brushes that the belts operate, one on each machine.\015\012Remove the brushes and clean as best you can. At the end of each brush there sho ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

I have an eureka deep steam extractor 2590 series and everything is working fine except for the motor it isn't moving is there a replacement part for the motor?? we think iit is the motor but could be wrong ??

Repairing unit wouldnt be cost effective . parts/labor $75.00 /$100.00 .if parts even available . ... Eureka Atlantis 2590A Wet/Dry Vacuum

My Hoover Wind Tunnel Bagless Pro Pet is making a very loud thudding noise when the belt rotates, belt seems to be intact and in place, what am I missing? Vacuum is less than 6 months old, belt is not worn and motor seems to be fine.

... Vacuums

My Sharp EC-l2TWT4 throws belts and I noticed the motor shaft was not running straight. My wife took it to my local dealer in Brainerd,Mn and they said it was fine.So I took it apart and found the plastic motor housing had melted at some point letting the motor twist out of alignment. Other than this, everything works great.Can I order this plastic housing piece somewhere?

I checked the schematics for that model and the motor housing for that model is no longer available. Your best bet is to either attempt to find a used part or trade it in and get a new unit. Sharp no longer makes any vacuums or parts which makes thes ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

I can't find replacement belt for little lux (original model bought in 1991). Stamped on back "Model 1673BA". Motor works fine but belt doesn't turn roller any more.

... Electrolux Little Lux Bagged Handheld Vacuum

I have a Bissell quicksteamer powerbrush steam cleaner. The power brush will not spin but the motor works to rotate it. I went to purchase a new belt but the guy told me the belt was fine? Any other suggestions?

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My bissell 6590 works fine with hose attachment. Motor shaft turns when belt and roller are off. When belt and roller are on it's noisy and smelly. Now one end of the roller actually melted in the holding slot. Do these rollers wear out like this or should I be looking for another problem.

Replace the roller,belt and before instalation clean motor shaft where belt rolls. you can turn on the vacumm and using a knife scrape the motor shaft from the black dirt. ... Bissell 6590 CleanView Bagless Upright Vacuum

The brush rollers on my hoover mach 5 won't turn. I've cleaned everything and checked the belts and everything checks out fine. I had the vacuum for about a year.

I had the same problem. The problem is the small v-belt for the roller brush (Hoover part# 38528034). Although it looks in good shape, it's been stretched too large for the idler to keep good tension. The tension on that belt varies with the ... Hoover Vacuums

Hello, I have a Hoover 3200 Turbo Power vaccum. while the motor appears to be working fine the vaccum no longer picks up the dirt. I turned the vaccum upside down and the belt appears to be broken. would a broken belt stop the pick up, there appears to be no suction. This vaccum is approximately 10 years old. is it worth fixing? I live in Virginia Beach Va, where would I take the vaccum for repair? my zip code is 23456- Thanks Cleta Goode

... Hoover Vacuums

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced

There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

WST 1600A I purchased this vaccum about four months ago from Heartland America. Up to this point it's worked fine. After cleaning it this time when I went to start vaccuming again it runa for about 10 seconds and cuts off. I've changed the battery, taken everything that can be removed out checked it and replaced it. THe motor sounds like it's straining. I have not taken the housing off the motor to see what's going on with that. I misplaced my manual.

It sounds like there is a clog. If there is no air flow it could be overheating. ... Westinghouse WST1600 Upright Vacuum

The motor that turns the rollbrush does not seem to be turning. How can i check to see if the motor is still working? the belt looks fine.

Have u tried getting access to the motor 2 check that the spindle the belt goes onto is turning or has the belt strectched marting ... Eureka Uno 2998AZ Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0721 seconds