Having problems with your Vacuums ?

I am replacing drive belt on Eureka 4870 upright. Before installing I removed bottomplate and was cleaning out accumulated lint, hair and grit. Found a pair of identical (reciprocal) felt gaskets sucurely inserted above and below the roller brush, and one small loose piece of felt approximately 1/3 inch wide by 1 inch long that came out as I was pulling out debris. It has a slight crease across the middle as though I was not resting on an entire flat surface, but I find no other clues as to wher


Answers :

If you go to this URL:\015\012
\015\012http://www.VacPartsWarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012
\015\012in the exploded view of the unit, identifying the parts and look at item 18, I believe it is where your felt parts came from.\015\012Also looks like you can order the replacement part(s).\015\012
\015\012If you run into any problems, feel free to contact me.\015\012
\015\012Paul
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am replacing drive belt on Eureka 4870 upright. Before installing I removed bottomplate and was cleaning out accumulated lint, hair and grit. Found a pair of identical (reciprocal) felt gaskets sucurely inserted above and below the roller brush, and one small loose piece of felt approximately 1/3 inch wide by 1 inch long that came out as I was pulling out debris. It has a slight crease across the middle as though I was not resting on an entire flat surface, but I find no other clues as to wher


If you go to this URL:\015\012\015\012http://www.VacPartsWarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012\015\012in the exploded view of the unit, identifying the parts and look at item 18, I believe it is where your felt part ... Vacuums

So, I was sewing along and heard a thump...kind of sounded like a louder version of what you hear when the needle hits a pin...but I wasn't using pins. This, of course, lead to the thread jamming so I had to clear that. When rethreading I pulled out the bobbin case to make sure it was seated correctly and found a kind of "v" shaped piece of wire (about the width of a paper clip I guess) sitting loose under the bobbin case. I took it out and threw it away. Still can't pull up the bobbin threa


That part was the hook end of the spring that was supposed to put tension on the bobbin - it will have to be replaced. This is a special flat spring that unfortunately only a repair shop of a dealer has it - you will have to take your machine to one. ... Vacuums

I would like to know how i get the very bottom piece off my vacuum off so I can put a new fidder hose on it? The hose is black and it is only about six inches long. its lacation is on the very end of the vacuum but between the end and the piece that gos along on the floor.


You don't have to take the vacuum apart.\015\012Assuming this is an Epic 3500 or similar upright Electrolux:\015\0121. Lay vacuum on it's side.\015\0122. Gently pull hose from power head. It's not screwed in so that should be eas ... Electrolux Epic 3500 Vacuum

I have a Dyson 17, the Absolute Brand special for pet hair. I think I have a blockage in the hose. Symptoms are: spewing out fuzz balls and small particles. I have checked all the blockage sites recommended by Dyson and all are clear except a small flexible transparent hose, 6 or 7 inches long, curled up underneath the cleaner head/brush bar unit. Any ideas? I've tried to pull out the stuff stuck in there, but I'm afraid to perforate the hose and I don't know any way to disconnect it.


Try dropping something like marbles into the hose and shake it up and down, may loosen it up enough to draw through.hope this helps you out. ... Vacuums

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa


Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

A piece fell out when I was emptying the bin and I can't figure out where it goes. Gray, about 4 inches long, strait with small pegs down one side.


It sounds as if this is the piece desinged to scrape lint from the screen on the filter cartridge holder. There should be two slots near the top of the dirt cup, about in the middle, that this piece snaps into, with the pegs facing the filter. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

It works well until it bumbs a wall. When it backs up it will not go forward again. I took it apart and noticed a cable is lose. I dont know where this cable hooks up to. One end is on a plastic disc on the end of the motor. The other end looks to have been pulled lose from somewhere. Its only about an inch and half long.


... iRobot Roomba 560 Robotic Vacuum

Roomba goes in a circle moves about 5 inches and then turns in a circle again. It won't dock or go any farther than a few inches before turning in a circle again. The roomba has been cleaned inside and out. All hair and debri as been taken out of the wheels and brushes. i opened the case and cleared all the debri and i dusted the sensors in the front. Not sure what to do now.


... iRobot Roomba 550 Vacuum

I have a yellowMiele Vacuum,model=Electronic Air Clean Plus S3121. On the main body the part that the pipe/nozzle clicks into has a piece that has snapped off. I can see this by lifting the lid and the black plastic piece that is screwed to the inside of the lid has a piece chipped of it which means that when the nozzle is clicked into place it is completely loose. There is a black piece that clicks into the inside of the hoover into this broken part which is still ok so at the moment by linin


Generic problem for all Vacuums\015\012I have a yellowMiele Vacuum,model=Electronic\015\012posted by maura497 on Apr 18, 2008\015\012Report abuse\015\012 ... Vacuums

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.


The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

Sears progression kenmore canister va. Model 11623612300 on the wand, the plastic piece broke off, there is one long wand with two piece to it well the plastic piece, not on the bottom, where it hooks into the beater bar thing, but the other plastic in the middle. Can this be replaces?


Hi.The part is probably available as replacement.Please click here ... Kenmore Vacuums

Bissell model 1694 rug scrubber works for a while then makes a loud noise when you pull it toward you like it is. Umping over something, roller is very easy to pull on, is it loose or a belt?


Dear Sir:Possible the motor can be faulty, or test the belt if is crack and replace. However you must see if there are some debris inside. Please see the section troubleshooting in your user manual. Download Biseel.com or www.fitness.manualsonlin ... Vacuums

On a filter queen 360 vaccum the electrical connection from the hose to the wand was loose and over time the electrical arcing burned up the female conector piece. Is there any way I can replace this without having to buy a new hose! Where would I find this female conector piece.


I am having the same problem On a filter queen 360 vaccum the electrical connection from the hose to the wand was loose and over time the electrical arcing burned up the female conector piece. This sounds to me like a manufac ... Filter Queen Vacuums

Model 116.27914 power mate connection to lower wand is loose. Head unit works when pushing forward putting downward pressure on it, but looses power when you pull back on unit and connection is lost.


... Kenmore Vacuums

How do I fill my dunhill gas lighter with gas using a Swan lighter refill?Yje lighter is about 2.5 inches long and about 0.5 inches wide with a release button at the bottom


... Vacuums

I sucked up a long piece of string, and it rolled around the bottom and smelled like burning. The piece of string is gone, but the motor doesn't sound like its engaging. Is this going to be expensive? Can I do it myself?


Flip the vac over take off the bottom cover plate to expose the belt and see if it still actually on the shaft, more than likely when you tried to run the vac while the string was wrapped around the beaterbar it caused the belt to either snap or stre ... Bissell CleanView II Plus Upright Bagless VacuumVacuum

The heated solutions only sprays out to the floor in a 3 inch area. It takes a long time to clean the floor with only 3 inches available. Are there some nozzles somewhere on the machine that I need to clear out? If so, how do I access the nozzles?


There are two nozzles (either red or white) on the unit located behind brush. Use an old toothbrush to clean them off and that should resolve the spray issue. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

When running the 2100 Electrolux vacuum, it is stopping and starting when pulling or pushing the floor attachment. Seems like the connection at the top of the handle is a little loose or the electric tabs are loose where the hose connects. Any ideas?


Other option is that on the hose end of the electrical connection, you can use an awl on the electrical connections to bend them in slightly so they make good contact when they are automatically plugged in when you connect the wands. HOWEVER, ONLY D ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Model UH60010, Series X12.0, Mfg code K09A. While attempting to use the hose and the extensions to clean shelves, my wife reported no suction. I removed the brush roller and the plastic piece just below where the hose opening is located and saw a "flapper" door that was closed and had some debris sort of jamming it. I removed the debris, but the door requires extreme pressure to open to permit the dirt, etc to moved up thru the opening , through the hose, etc. I thught maybe that somehow tg


Hello,Check to make sure\015\012the dirt canister is empty. If dirt canister is full, then you will \015\012experience\015\012reduced suction. Empty dirt receptacle.\015\012 Could\015\012 be a clogged hose - ... Vacuums

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks


If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

I have a Dyson DC17 and I cannot get the detachable hose to pull up to use. I have tried pulling it up but it does not move and I can not use my detachable pieces. Is there a button I need to press - How do I fix?


Yes there is a button to release it near the handle i think , \015\012\015\012hope this helps ... Vacuums

When replacing the motor I noticed 2 pieces of black foam had fallen out, but I don't know where from? slightly leans to the left


... Vacuums

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?


Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://64.49.205.183/v/u6451900.pdf ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0428 seconds