Having problems with your Vacuums ?
Janome dc4100 loopy untidy stitching on reverse sewing machine
Totally rethread your machine, if the underneath threads are looping it is your threading on top that is causing the problem. Make sure that you thread is not tangled.
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Janome dc4100 loopy untidy stitching on reverse sewing machine
Totally rethread your machine, if the underneath threads are looping it is your threading on top that is causing the problem. Make sure that you thread is not tangled. ... Vacuums
I have the Janome 6600 P. Beginning a seam the thread knotted and the machine made noise and needle would not move either up or down. I manually moved the needle using the handwheel and cut away the knotted thread. I began sewing again but instead of starting at the edge began about a half inch down, forward stitched, reversed to lock threads and problem repeated and received the message to "Stop for safety purposes". Did that. Referred to the manual, tried manual recommendation. Did not work. I
My Singer Sewing machine (model 6215) is now only sewing in reverse. After pressing the backstitch button, the button seemed to stick in the backstitch position. I was finally able to pull the button out but my machine continues to only stitch backwards. What do I do now?
It's stuck inside. Open it up so you can see inside the bottom, look for the feed dog mechanism and you'll find where length of step is varied, this is where the reversing takes place too. Tapping gently and oiling will free it up.lp ... Vacuums
Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna
... Singer Vacuums
I have a Janome DC2007LE sewing machine. I am trying to do a regular buttonhole. I have the correct foot on and the buttonhole lever down inbetween the gap. I also have my button in the back to make the correct size buttonhole. When I start to sew it will make the front bartack and then only a few stitches into the left row. Then it beeps three times quickly and shows bL in the screen. I can't find what that means. and don't know what I'm doing wrong. It is doing this with both square an
We have a vogue stitch janome model 539 115v sewing machine. we were trying to sew but, the thread is not picking up from the bobbin. the thread keeps breaking and we are unsure what tension setting should be used for cotton cloting. please help. thanks! tom staron
Janome sewing machine Harmony 2139 The bobbin thread is not connecting with the needle to make a stitch. We have put in a new needle. Using needle 4 tension
A common problem is if needle is in backwards. The small groove side should be toward the operator. As the needle starts back up after going clear down, a small loop should form on the side of the needle away from teh operator. The shuttle has a p ... Vacuums
Please please help me! I recently bought an Empisal Celebrity 550 Sewing machine, I've used it maybe 4 times up to now. Yesterday I was sewing with it and everything was working perfectly, today, when I got home, I plugged in the sewing machine and started sewing, just to see that the bottom stitch is completely loose. It's making this loose loops instead of stitches? I didn't change a knob or anything from working with it yesterday to today, so I don't understand how it all of a sudden doesn
Have a 3 year old Pfaff Creative Vision. Has less than 14 total sewing hours on it. Has had issues in the past. Breaking needles, wouldn't stitch out designs in acceptable manner(badly distorted looking) breaking needles repeated, now it is changes stitches on its own, then went to sewing the same stitch but isn't sewing it consistantly. I have taken it back to the same professional to repair each time. Can thhis machine be repaired??? Should I trade it off and get another, this isn't my first c
It sounds like this machine has some kind of fault in it for sure. It can be repaired again, but will likely need to be repaired again after that - down the road. Personally I recommend you just get rid of this unit and go for a different model. Y ... Vacuums
I have an old kenmore sewing machine. When i run fabric through, the bottom stitching turns into a total rats nest. Its as if the bottom is pulling a ton of thread for each stitch. The top stitching looks fine. Not sure what to do and i am a total beginner at sewing! thanks
Check the tension on the bobbin thread and ensure that the bobbin is in the right way, the thread must double back on itself. ... Vacuums
I bought this machine about 3 years ago but hadn't used it due to illness. Now when I tried to sew with the Tuff Sew ,the threads continually break. If I can make about a 3 inch line of staight stitches without the top thread breaking,I consider myself fortunate The direction in the manual are extremely poor. I had to finish my project with my very old Bernina. I regret buying the Tuff Sew straight stitch. JLWebb
I do not have one but these machines require heavy duty thread...\015\012\015\012The manufacture recommends using only "#69 Bonded Nylon Thread"\015\012\015\012You should have a 18 to 20 gauge needle for that size threa ... Vacuums
While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!
Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums
I have a necchi sewing machine model 4795 and I am having trouble trying to do zigzag stitch for applique. Can you please help me with the settings on the machine. I have tried to use manual, but I still cannot get it to stitch correctly. Thank you.
We have a Singer 626 sewing machine. It's an old mechanical machine with heavy metal parts. The stitch selector was stuck, I removed the top and helped the selector to move. when I had to move the selector again, it was stuck and I pushed too hard and broke a component. I can fix the machine if I had a repair manual. I need to buy a repair manual. How and where can I get one? Thankjs Charlie PS. Im pretty mechanicly inclined and I was able to clean the machine and get it to work after
My Janome Harmony 8100 will occasionally stop and give me a System Error #1 - I cannot find anything about this error. It is a computerized machine with 70 stiches and attachable embroidery hoop. I first started getting this error with the hoop and now get it when I am just sewing. As soon as the needle goes down to the bobbin, I get the error. The machine freezes and the only way to get rid of the error is to turn the machine off. Sometimes I can get the machine going again, but now it wil
Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st
Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums
I have a Brother PR620 embroidery machine and I got a machine lock error. What should I do clear the error. The machine sews evern after the error however, it will not line up correctly with the hoop ( will not center), and the stitching is very uneven and ugly.
I got my Mom's Kenmore sewing machine and I an trying to figure out how to get the scalloping and arrow head stitches to work. I have followed the manual and I can get all the other stiches but those two. It is a Model 1451 zig zag machine. I realize it is old, but the machine is just like new. HELP. Thank You.
I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me
Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums
Janome sewing machine model 654. Wife needs to know how to string the thread for sewing. we have lost the owners manual. If anyone can help with a diagram.
I have a Janome DXL 603 sewing machine and I would like to use the darning foot to do freehand quilting and have not been successful. I have had a sewing teacher try while I was at a workshop and she could not get it to work either. Could you please advise?
I bought a stitch & go sewing machine, the instructions for threading the machine are hard to read could you please explain or email a larger versin , specifically #3, 4, and 5 , i know i'm doing something wrong thread is breaking
I have an old Janome sewing machine and when I plug it in at the power point and turn it on it sews without putting your foot on the pedal Can you help
I have to same problem as tony ... Vacuums
I just had this machine delivered yesterday (Janome Magnolia 7330). When I sew a straight seam (all I've tried so far) I get loops at the underside of the fabric. I adjusted the upper thread tension, but that did not help. In fact the loops got larger as I increased the tension. My thought is that I don't have the machine threaded correctly. Thanks!
Your problem is in the tension adjustment. also check the stitch lengths. \012\012Kdog ... Vacuums
Janome 6600 sewing machine. bobbin thread is gumming up underneath on a swimsuit knit type material (4 layers). Brand new machine had 1 1/2 weeks. Sometimes material goes down into the bobbin area jammed by needle. What am I doing wrong?
Make sure you're using a polyester thread (I use maxilock serger thread) then a stretch needle, and hold the tails of your thread until you get started into the seam so the fabric cannot push down into the opening on the throat plate.\015\012 ... Vacuums