Having problems with your Vacuums ?

I have a Simplicity model 6970 upright vacuum. It picks up great and there is no smell but it will over heat in about ten minutes and shut down. There are no clogs. Once cool, I hit the thermal reset on the back at it works great again until it overheats again.


Answers :

It could be electrical on the inside of the vaccum or your belt is the wrong size therefore making it over heat. Hope this helps?!



Please rate and comment - Thank You
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Simplicity model 6970 upright vacuum. It picks up great and there is no smell but it will over heat in about ten minutes and shut down. There are no clogs. Once cool, I hit the thermal reset on the back at it works great again until it overheats again.


It could be electrical on the inside of the vaccum or your belt is the wrong size therefore making it over heat. Hope this helps?!Please rate and comment - Thank You ... Vacuums

Eureka 4467AV overheats and shuts down after about 3 or 4 minutes of operation. I pulled all the filters to assure no blocked air flow. I assume the motor is not getting enough cooling air but i can't figure out why. checked bag for blockages as well as hoses. could the thermal protection have gone bad?


... Eureka 4467AV Upright Vacuum

Bissell 37604 Bagless Upright Vacuum. Hose keeps clogging every time I vacuum. Is there a way to prevent this? I am ready to buy a new vacuum, but it does do a great job picking up hair...until it clogs. It clogs at top of hose. Could the hose be kinked? It does not look like it.


That is a defect in the design of that style of vacuum. I went back to my old vac because I got so tired of having to unstop it. The sharp turns in the hose and the molded plastic causes it. Find one without the turns. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Dyson DC07 Vacume cleaner trips on thermal after 10 min motor not excesive hot resets after 15 min has been doing this for the last 3 mths. Could it be faulty thermal or motor overheat how can I check without changing motor


First, check both filters on that unit. the premotor filter on the side, and the hepa filter underneath the canister. if those filters are clean move through the suction channel and look for a clog or obstruction. also make sure the canister is clean ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I have a Eureka Maxima, this was a gift to me, but I have to say it is the worst vacuum I have ever used. Not only do I have a problem with the suction and the filter getting clogged, but it overheats - it takes me all day to vacuum my house, because the darn thing overheats after every room. Besides for tossing it off a cliff and buying a better vacuum, what can I do?


Get yourself a dyson ... Eureka Vacuums

No Suction I get great suction in the hose, but when I plug the hose back into the unit, there is no suction and the air flow indicator line goes completely red. I've changed the bag and filters. I took the small panel off the back and made sure there is no clog, and took the hose off to make sure there was no clog there. Still no suction. Please help.


I about to say that's always a clog of some sort that causes that ... Miele S7210 Bagged Upright Vacuum

Great suction through handle, no clogs anywhere,


OK - there are two obvious things to check: 1. Make sure the brush is rotating. The DC14 has a 'brush control system" operated by a knob on the base in front of the right side wheel. Make sure this hasn't accidentally been moved to the "off" position ... Dyson DC14 Full Access Bagless Upright Cyclonic Vacuum

My Lindhaus Diamante 300 has great suction but clogs


Sounds like you have some form of an obstruction in the hose ( i once found a tooth pick sideways in mine) most models allow for the hose to be disconnected from the vaccum itself, also make sure theres not a setting for attachments also, some models ... Lindhaus Diamante 300 Upright Vacuum

Centralux - unit will operate for 10-15 minutes then shut down. We hit the reset button, unit operates for 20 minutes then shut down again. Had customer svc stop by, they checked the hose, filter, no clogs, etc. ANy ideas


Check the screen. It's located underneath the motor. You can see if it's clogged by removing the filter and with a flashlight look up at the bottom of the motor. If it is clogged, the easiest way to clean it is unplug the vacuum, disconnect the two m ... Electrolux Centralux Vacuum

Hoover HU 4205 not blocked up, motor overheats and trips thermal cutout ,after a short time.


... Hoover Vacuums

The hose works great, but when I try to vacuum the carpet it doesnt work. The brush is turning, but I don't feel much suction. I checked for a clog and didn't see any.


You probably need the clutch replaced. This needs to be done every 1 to 2 years for most people ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The DC04 Zorbster runs slow, it still picks up but I am worried it will overheat. If I hit it at the front, the motor picks up speed until the next time I start it up. Can you help???


The problem is likely caused by either (a) a broken or worn microswitch operating lever or (b) a faultyt microswitch. With the bin removed, the lever becomes visible just above the filter upon which the base of the bin normally rests.Repl ... Dyson DC14 Bagless Upright Cyclonic Vacuum

Vacume overheats and shuts down I replaced the motor.When it cools down it runs again.


The filters had to be cleaned out with air. I replaced the motor for nothing.There are two filters and the cannister give them good cleanings with an air gun. ... Kenmore Vacuums

I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.


- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum

My bissell aroma pro had a horrible burning smell then stoped sucking up water. the motor was still working and water was being feed out just not back up. the machine was hot as i had already cleaned 3 rooms in the house. i let it cool down but the burning prob returned as soon as i turned it back on. any help would be great thanks


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

I recently purchased a bissell proheat 2x and have used it several times with great results, the problem I am now having is no water being released from the bottom of the machine and the gauge is not spinning. What could be the problem. I have taken the machine apart thinking maybe something is clogging it.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Liftmaster garage door opener and the garage door faces south. Normally the opener works great except at certain times on a sunny day.The sunlight is not directly hitting one of the sensors but the door will comedown as far as half way and then it will go back up and the lights will flash. If I go inside and use the button I can hold it down until the door is fully closed. However, sure is a pain to have to take the car out, go back into the garage, shut the door and then leave the h


Sounds like a problem with a limit switch or something getting in the way of the electric eye that interrupts for safety reasons. \015\012Clean the electric eye transmitter and sensor of debris and cobwebs and make sure the wires are attached properl ... Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano


... Electrolux Vacuums

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.


If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum

My hoover vacuum runs for about 10-15 minutes then the saftey feature shuts it off(overheat?). i have taking it apart a cleaned it with no results, added new bag also. after an hour it cools down and works again. do i just need a new vacuum?


Do you have suction through the tools? Does it look like it picks up when it runs? The machine could be clogged and that would cause the problem, but unfortunately the sensor that shuts the machine off could be bad if the machine isnt clogged. Its no ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Eureka 11 pound bagless vacuum overheats when used for an extended period. Have to turn it off and let it cool down then use again.


Got info at a FREE site. ... Eureka Vacuums

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?


Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have had my shark steam cleaner for 6 months now and I love it, but I have hit a snag. I have not useed it for a cople weeks and when I plugged it in today - no steam. It seems to heat up, but there is no water coming out - the cleaning pad stays dry? Am I supposed to do some sort of regular cleaning of the water resovoir to prevent clogging or something?


Hi,No, these things don't last long...send it back...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0242 seconds