Having problems with your Vacuums ?

How do you thread the 33IKI? Can't figure out how to put the thread.

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you thread the 33IKI? Can't figure out how to put the thread.

... Vacuums

The tension knob came off of the front of my sewing machine while I was sewing. I cannot figure out how to put it back on. I have the metal rod that fits into the back of the tension knob, but cannot figure out how to put it back into place. Keeps falling off

It sounds like your machine is the kind that has a knob with a 'set screw', a teeny tiny screw that tightens and holds the thing in place on the rod. Look for a small hole, probably on the bottom and look for a very small screw near the machine. ... Vacuums

My Kenmore sewing machine timing has gotten off. I am sewing a big upholstery project and it starting bunching thread from the bobbin. The thread is so heavy that I had to put some pressure just to get it undone. This happen a few times and then I found it wasn't sewing at all. When I evaluated without the materials in place I could see the needle would catch on the white plastic piece under the bobbin and the thread would not catch on the metal arm. It appears to be off by 1/4 - 3/8 inch.

HelloDisassemble your bobbin case which is realy quite easy, clean\015\012thoroughly with a brush and air, paying particular attention to any\015\012rust that may have formed, and any thread that may have weazeled it's\015\012way into sma ... Kenmore Vacuums

I just got a new machine (new to me anyway) new home hf106 model. i need to thread the bobbin on the new thead i am using and am not sure where to put the empty bobbin and how to thread it. help!

Janome New Home? Unfortunately, Janome doesn't put the manuals for older machines on their website. Your best bet is to contact your local Janome sewing machine dealer and ask for a "copy" of the manual from them. A photo copy should b ... Vacuums

It's been awhile since I have used my shampoo system on my Ultimate G series Kirby. Well, as instructed I took it apart and cleaned it. Now I can?t figure out where to put the ?screen cap? and ?sponge filter?. I have my manual in front of me and the only place it shows the filter and sponge (page 35 in the manual) is when it?s been taken apart to clean. It doesn?t show where to put it back. I don?t know what I would do without all the pictures in the Kirby manual. HELP! Thanx. Visual Kirby Vacuu

Hello,\015\012The littlew round screen goes in the hole where the hose attaches to the tank. The round foam filter goes up in the hole underneath the on/off valve for the foam. Here is a guide if you need any more help...\015\012\01 ... Kirby G6 Bagged Upright Vacuum

My daughter pulled to hard on the ceiling fan pulling out the chain. i have taken it off and apart, nothing appears to be broken but im trying to figure out how to put it together so it retracks, i assume it has something to do with the tension of the small spring inside of it, but not sure how to put it back together im wondering if there is a internal diagram of this ???

Don't even bother to repair the pull chain switch, get a new one at KMart, HomeDepot or similar store for less than $2.\012\012Two times I've repaired one, it comes apart when I need it the most.\012\012Good Day! Don't forget to rate thi ... Vacuums

Cant figure out how to thread elna 1000 lotus sewing machine. also the bobbin keeps getting tangled. if you could send me a diagram on how to thread and bobbin i would appreciate it

... Vacuums


You need to take the bottom cover off to expose the motor's pulley, and the beater bar. take the beater barr off by just pulling it off, and follow the marks on the plastic where the belt goes. ... Dirt Devil Vacuums

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.

... Windsor VS14 Versamatic Bagged Upright Vacuum

Need instructions how to use Hoover Steam Vac Spin Scrub. I borrowed it from my Sister and she left it with no instruction book or letting me know how to operate it. I put water & cleaner in top tank. That's all I know to do. Do I put any water in bottom tank? I figured not, since that is probably where the water goes when sucked up by vac. Do I leave lid on bottom tank? I usually use a commercial cleaner, and this is very different. I need to know NOW, as I must return it to her today, and I'm

I did have a solution in just a few minutes. Someone responded with a solution that gave me the website where I could go and print the manual in pdf, so did that, and checking instructions I was able to clean my carpets and get the shampooer back to ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Wife took Dyso DC 26 Handle Wand off the Vacum. Can't Figure How to Put It back Together!? We Must B STUPID!

This link below is for the manual that will give you full instructions how to replace the hosehttp://media.dyson.com/downloads/UK/floorcare/Manuals/ ... Dyson DC26 Bagless Canister Cyclonic Vacuum

I took out the bobbin case & not sure if I put it back correctly. Now I had my thread going under it instead of over it.

Download the manual here > http://www.singerco.com/accessories/instruction-manuals ... SewShop.com Singer Model 4562 Instruction Manual

I cannot figure out how to put the bag in

Theres a slot on the front stick your 2 fingers in there and pull ,its right above the front cover,then just pull the old bag out and push in the new bag.please leave feedback ... Bissell 3522 PowerForce Bagged Upright Vacuum

Have a dirt devil breeze that the adjust. wheels fell off while replacing the beatter brush. can't figure out how to put the wheels back on

... Dirt Devil Breeze Bagless VacuumVacuum

How do I change the outer bag clip? Can't figure out how to get the top apart to put in the new clip. The clip that goes to the handle.

I had a Kirby Classic and I had to slide off the clip.Don't rate me if this doesn't work. ... Kirby Generation 3 Bagged Upright Vacuum

I can't figure out how to put the bag on.

I had a terrible time trying to install a bag, too! The hinged piece must be closed. Hook the cardboard backing on the opening and \015\012line up the pieces sticking out on either side of the hinged piece with the openings in the cardboard o ... Oreck XL2600 Vacuum

I can't figure out how to put the belt on I have a kirby G model

Here's a free guide to help you out!\015\012\015\012\015\012http://reviews.ebay.com/C ... Kirby G5 Bagged Upright Vacuum

Carpet cleaning brush noise. When put in carpet cleaning mode, a loud noise comes from the brush bar area. We see no visible obstructions and have cleared threads and hair.

It's likely that one of the brush roll bearings has worn out. This is not uncommon. I think you'll find that you have to replace both the brush roll and the sole plate at the same time. Dyson sell them together as a kit. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Looking for operation manual Can't figure out how to put it together.

You can often download manuals from the maker's website. Otherwise, if you want more specific advice from this site, you'll probably have to tell us what the machine is. ... Vacuums

Vaccum cleaner needs belt put on and i have belt, but can't figure out where it goes except that it is over the rotator wheel from there i am lost and i have no manual

Wish you had given your model number because they are different. On some, the belt goes over the motor shaft, then over the brush roll. Some you have to remove he top cover to get to the motor shaft. Some go over the motor shaft, then over the big ... Hoover Vacuums

HOOVER F5906-900 I am having trouble figuring out where the inner hoses go, A friend barroed it and took them off to clean them and did not put them back properly. Would you please send me Scamatics to see where exactly these go so I can shampoo my carpets before I go crazy. Thank You Misty Winslow [email protected]

Here is a break down, you may be to trace the lines:\015\012\015\012 ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

I have a bagless cyclonic shark stick vac. I cannot figure out where to put the hose to use the attachments.

... Euro-Pro V1828 Shark Stick Vac Bagless Vacuum

I have an older hoover vacuum and cannot figure out how to put the belt on?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=542813\015\012Generic problem for all Vacuums\015\012I have an older Hoover\015\012Posted by rrunne ... Vacuums

The belt is broken and i cant figure out how to get the wheel of to put a new one on

The control height adjustment knob should simply pull off - grasp it gently and pull off. Then locate the screws on top of the floor head to get into the belt area. ... Euro-Pro NV31 Infinity Vacuum

Turbin hey its me Lisa I took the turbin apart and know where the wheels (gears) go but they have this little bearing or what ever it is its round and has a whole thru sent can't figure out how it goes to put it back together. the thing turns really good now after I soaked it HELP

You should have it all back together now. Hope it is running ok. \015\012Lauren(reddevil6) ... Hoover F7220900 SteamVac V2 Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0334 seconds