Having problems with your Vacuums ?

We have a jvc nx pn10 ipod dock. Every time we turn the power on it says "Hello" briefly then P-ERROR. Nothing will remove this message. Can you please help?

Answers :

(This question should not be in the Vacuum section - the device in question is a Clock/Radio/iPod dock) I had just this problem but could find no solution on the Net. JVC could provide only a PDF of the manual, which nowhere mentions P-ERROR. So, with nothing to lose I opened the thing up (9 screws - don't forget the three on the very back, next to the RCA socket & aerial connector). I found some crud on the circuit board - took it out (three flat cables, two speaker connectors, one power connector,four screws), cleaned it with alcohol (methylated spirit), dried it with a hair dryer and reinstalled it. Result - no more P-ERROR.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a jvc nx pn10 ipod dock. Every time we turn the power on it says "Hello" briefly then P-ERROR. Nothing will remove this message. Can you please help?

(This question should not be in the Vacuum section - the device in question is a Clock/Radio/iPod dock) I had just this problem but could find no solution on the Net. JVC could provide only a PDF of the manual, which nowhere mentions P-ERROR. So, w ... Vacuums

Good morning, I have a Krups Variomix 3000 Premium, don't have a user manual, and haven't used it yet as I can't get the blender to lock into place. The user manual downloads that are on-line say the link has been removed. Please can you help me get the blender to work? Thank you, Marian

This is listed under vacuum cleaners as the repair catagory, is that what it is? ... Vacuums

After removing the filter, I cannot get to battery on the Dirt Devil Kone M0213, there are two horizontal screws. Removing them does not help getting to the battery, no way to remove the insert where the battery is located.We have two of these, however they did not come with a manual for dis-assembly. Please help or proved a diagram on how to remove the battery. Many thanks, Wesley Lennon

Sheesh, did anyone actually read the person's question? It's about the battery, not the filter.\015\012\015\012You have to get the outer cover off and it's not easy. There are four tabs which need to be released. I have to use a very sha ... Dirt Devil KONE Hand Vacuum MO213BLU Vacuum

Hello can you help me please? I have a Kirby G4 vacuum cleaner, It did work ok until it started to give off burning smell and lots of sparks from the brushes. I have changed these brushes, the motor still rotates but it still gives off sparks and burning smell. Do i have to change the motor as well? Can you help please? Thankyou Martin

Some debris, even sand or dirt, probably got into the motor, causing damage to the armature. If this is the case, you will need to replace the motor. The burning smell from the motor is generally a sure sign of a bad motor. ... Kirby G4 Bagged Upright Vacuum

My Sc-505 hello, can you please help me? i got the Sc-505 from my sister (already used) and she did not give me the user manual. i need help at least with the basics, do you think youcan help me? thank you very much.

Go to the shark company online at http://www.sharkclean.com/cg ... Euro-Pro Shark SC-505 Handheld Steam Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Keep getting message 'please remove and clean Roomba's brushes'. Have removed and cleaned brushes and even fitted new one's but still getting message. Also brushes sometimes rotate, sometimes not and not picking up very well at all. Help!

Must be your inbox is full, Delete old / unwanted messages. It should resolve the problem ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

Telescopic duster hello, i was wondering how you remove the yellow telescopic duster from the side storage spot? It says it's a self-cleaning duster, but I can't seem to remove the duster from the container

Just pull straight up. They're a bit stubborn at first, but there's no real lock or anything in there, so trying to get it to release by twisting or pushing on anything won't help. (I know this because I spent quite some time not wanting to break a c ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

Runs for awhile then says error 2 please remove and clean roomba's brushes i do then runs for awhile and says same thing no dirt on brushes?

I had the same problem. You must clean this parts and inside this parts: Remove hair with cleaning toolRemove Roomba's brush bearingsClean Roomba's brush bearings with cleaning tool ... iRobot Roomba 560 Robotic Vacuum

The removable filter at the front is cleaned regularly, and is not clogged. However, the machine appears to be suffering from being clogged by dust, as it has started to make a high pitched noise, and I fear it may burn out. I can see some dust inside the front panel but cannot see how to remove the front to clean it out. (NB. I have located two screws - one on either side - but cannot see how to proceed further.) Please help! Thank you.

\015\012\015\012Hi,Here\015\012is a tip that I wrote about my Bissel but I bet you have the same\015\012problem and the hose is clogged...Bissell Bagless Upright\015\012 ... Vacuums

Hello, could you help please. I have a Bissel ProHeat 9400-M. The water remains in the bladder when the machine is on, in other words nothing happens and I cannot clean with it. Inside the tank the small flap is in the open position. I have always used your products although I did run the Bissell over an area that had been cleaned with another product. Could that have caused the problem by blocking it somewhere? I have cleaned everything and cannot see a blockage. Thank you for your help.

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hello Can You please help me with my SC505-h. My sister gave it to me before she moved, but the user manual was not there, and i have no clue how to use. i really appreciate your help. thank you very much, have a great day, evlin lebreault

First lubricate the screw top with WD40 and then fill it up with no more than 8 oz of water. you should be able to find a manual online. ... Euro-Pro Shark SC-505 Handheld Steam Vacuum

Hello experts. I have a Hoover u6454-900 vacuum and need new belts a thin one and a thicker one. and I do not have the manual and do not know the parts numbers for these. please please help.

... Hoover U6454-900 WindTunnel Bagged Upright Vacuum

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony

... Kenmore Vacuums

Sponge filter I have a kirby sponge filter for my Sentria shampoo system and dont know where it goes. It stop working and making foam. Kirby sent me the sponge filter saying this is what i need and i would know where it goes. I dont nor kind I figure it out. please help!!!!!!!

On the end of the shampoo tank where it attaches to back of motor where the bag is normally attached ... Vacuums

Roomba 550 keeps saying please remove and clean roomba's brushes. I have done so and keep getting error message.

Pull both brush rollers out.pull off funny looking yellow ends and clean out hair ect. ... iRobot Roomba 530 Robotic Vacuum

Hello, I have a problem with ma sound driver . Before it works properly but while I instaled realtek driver volume controler dissaper and no sound . Please help me?

Roll back driver in device manager ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Turbine Hi I found out through your site that my turbin is bad on my steam vac and I found some information as well on how to disasemble the steam vac to get to the turbine but still was wondering if there were some more detailed instructions on how to remove the turbin. I am a sigle mom and doing the work on the steam vac myself and need a little more detailed instructions. Please help asap and have a bless day.

There are some screws on the bottom that have to come out so you can remove the top housing. Take the brush block out, there are 2 screws above where it sits. The turbine sits near the front, and in the mid section, 2 screws on the front of it and 2 ... Hoover F7220900 SteamVac V2 Upright Vacuum

Hello! I have a Kenmore Progressive bagless vacuum with the Easy Clean extended life filter. The model number on my vacuum is 34728401. I was vacuuming the carpet when it just stopped running. The dirt sensor light will come on, but nothing else. The belt looks fine, and I don't see anything keeping the beaters from rotating. Help Please!!!

You can have power to the dirt light sensor, but it seems like the motor itself is not using the power supplied. ... Vacuums

Elna TX Electronic machine. Top thread gets tangled in rotary hook when straight stitching. Top thread is also found attached to bottom of fabric when removed from machine. Can you help please.

Try a different type of thread for this operation. ... Vacuums

Miele revolution powerplus 5000 - extension tube gets "stuck" onto the handle, very difficult to remove when I want to change tools. Help much appreciated please

... Miele Vacuums

I have a W580i bought today. When I try to send messages it just says they are in a queue and will not send them? help please!

I rang the customer services in the end and they said try the sim card in another phone which worked then said that it was a fault with the phone.\015\012Took it back today but apparently it wasn't fully activated so all sorted now. ... Vacuums

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

Roomba Discovery My Roomba turns on and moves but the brushes won't turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it's brushes cleaning "please clean Roombas brushes" So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)

I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the "spot" and "clean" buttons for 30 seconds. Replace battery. This has worked for my Discovery model ... Roomba Robotic Floor Bagless Vacuum

Belt?! hello, I need to change the Eureka Oxygen Canister Air Driven Upholstery Tool's Belt (model 5860Avh), but I don't know which one to get? any help please? Best, Pierre.

You will probably have to order it online. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0931 seconds