Having problems with your Vacuums ?

The slowcooker only has high and low settings. Im trying to figure out what 300degrees F. would be


Answers :

134 degrees Centigrade
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The slowcooker only has high and low settings. Im trying to figure out what 300degrees F. would be


134 degrees Centigrade ... Vacuums

Bissell will spray water when set to water rinse, but as soon as it is set to light, normal, or heavy cleaning, there is no spray. I have tried priming but to no avail. I put plain water in the solution tank to test without ay success. It is like it loses it's prime whenever you try to use a solution mix. Once you set it back to water rinse only and go through the priming steps, it is OK. Any help would be appreciated. Thanks.


Please check the following with liquid in both tanks.\012 \012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\012- Check for ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara


... Vacuums

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.


When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would


... Hoover L2310 GUV Central System Vacuum

Vacuum height won't go on low carpet setting. Dial will go on medium and high, but not low.


Make sure you're not trying to adjust w/ handle in upright locked position because thewre is a cam which raises the vacuum head a little bit when handle is locked in upright position. If this is not the problem, turn vacuum upside down with handle in ... Hoover Vacuums

How do i lower my vacum setting it is set to high i am trying to vacuum ar rug


... Dirt Devil Featherlight Bagless Upright Vacuum

Trying to set up a shampooer on the Kirby G4 vacuum. Cannot figure out how to get the dirtbag off in order to set up the shampooer.


See if this link to kerby helps it has a few videos\015\012\015\012http://www.kirby.com/Portals/0/videos.html ... Kirby G4 Bagged Upright Vacuum

When operating the bosch terrossa vacume cleaner its make a load noies when turning up from low powe setting to high power setting.


... Bosch Vacuums

When i set it on carpet instead of bare floor it is hard to push when i vacume (when i turn nob it only has two settings floor and carpet no high pile or low pile)


Hi there,Sorry to hear you're having difficulties using your DC14 on this particular carpet. You may want to contact your carpet manufacturer to check it's suitable for cleaning with a vacuum cleaner equipped with a revolving brush. Manuf ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Rainbow E2 has been working great for years now, but recently it has stopped working on the vaccuuming setting, but will still run on the low speed air cleaning setting. I hope it is something as easy as replacing the switch. Would appreciate any tips to determine if that is the issue or possibly something larger. Tks in advance for the info/help.


Still need help, let me know.\012\012Thank you,\012Ralph ... Rainbow E series Canister Wet/Dry Vacuum

I have a Kirby G7 and it will run on the low speed setting. When i switch to the high speed it starts to spark and smoke near the back of the motor near the windings. Do i have a motor going bad or is there a simpler fix.


It's probably doing that on low speed too, you just aren't noticing. What you'll have to do is get to the motor. Look at the armature and see if it's scared, missing an pieces, scratched up.. if so, then your motor is shot, throw it away.. If not, if ... Vacuums

Brush bar not spinning when set to high or low on carpet


1) adjust the belt, see for broken or worn, and replace2)see for brushroller obstruction, and clean it and repair3) see if the brushroller without belt run smooth, otherwise repair and fix it.Lubricate.4)See if the motor run without load( ... Vacuums

Dyson DC 14 hose has no suction, with or without brush attachments. Hot air shoots out from the base of the canister when I try to use the hose. I cleaned the top filter, but can't figure out how to remove the hepa filter to clean it without destroying the case. It looks like it might take three hands to insert pennies and "flip" the case open as is suggested on a youtube video for a different model. Would this even help, assuming I could get the thing open?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

No manual with bush slow cooker. 3 settings high low and auto. need to know cooking times and how auto works.


... Vacuums

On hoover steam carpet cleaner, the brushes do not rotate on low or high settings.


Follow these steps if the Brushes Fail to Spin\342\200\242If the brushes on your Hoover carpet cleaner fail to spin, there may be a problem---some sort of blockage---with the suction or with the belt that turns the brushes. \015\012Turn t ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I'm a bit confused. I just purchased the Spot Bot Pet and am trying to figure out how to fill the tank. I see where the lines are for set in stains but it isn't clear to me why there are 3 lines, one for water, one for "OxyGen2" and one for "Formula".Please explain


... Bissell 1200A SpotBot Pet Robotic Vacuum

I purchased the Sharp Ultra-Thin Digital Alarm Clock Today. SPC431A The first one I bought the digits did not show up on the right side of the clock. I went and exchanged it for another, after showing the store what was wrong with it. I have now been able to set most all of it, but... 1) It is on 24 hr mode, instead of AM or PM. The instructions that I have do not say anything about a 24 hr mode. I have tried running through the clocks hours, to see if that would change it back to AM or P


... Vacuums

DZ9080 IRON IS NOT VERY OLD, BUT HAS HEATING AND STEAMING PROBLEMS. IT MAY BE ALL HEATING RELATED! MY WIFE WILL SOMETIMES JUST LEAVE IT "ON" FOR TWO HOURS AND THEN IT WILL START STEAMING AGAIN. I CANNOT MAKE SENSE OF THE HEATING INDICATORS; SOMETIMES IT WILL STAY GREEN NO MATTER WHERE YOU SET THE DIAL ---- AND IT DOES NOT FEEL HOT! WHEN I TRIED IT AGAIN TODAY, THE SHOT-OF-STEAM WORKED FOR A WHILE (AND THE SPRAY WORKED), BUT THEN ALL IT WOULD DO IS DRIP WATER AT THE TIP WHEN TIPPED DOWNWARD.


I couldn't find any warranty information on this iron, but I suspect that the heating element either has a faulty connection or part of it has cracked, making contact at time, but poor contact at other times. The unit will have to be taken apart an ... Rowenta Vacuums

Have a fantom 12 amp vacuum cleaner and can't figure how to change the belt. I am afraid to try to force anything for fear of breaking the case. any help would be appreciated. Thanks,FRANK in N Y


... Vacuums

Dyson D17 I am trying to figure out where this thing goes. When I was taken everything apart it kind of pop off and did not see where it came from any help would be great.


I have the same problem and I am trying to see how to place it back inside on reassembly. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

While vacuuming a rug on high (carpet setting) the power suddenly decreased. Now it will only run with low power, not picking up items on carpet


It sounds like you burned the belt. Turn the unit over, remove the cover plate where you see the brushes. On the side of the brush roller is where the belt is located. The belt should be very tight on the roller. Also, you may see little black ru ... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

Levels/Settings I am having trouble changing the setting on my vacuum from 1 or "Low, Hard Surface" to any other setting. Without changing it, I am unable to vacuum on my carpet, since the setting is too low.


These height adjustments are designed so that they will not adjust when the handle is in the "back" position. This is so they will stay where they are set and not self-adjust while you are vacuuming. To change the setting, you need to return the hand ... Hoover Elite Rewind Bagless Upright VacuumVacuum

On our new carpet (which is not that thick but thicker than the old) I can't set the carpet thickness high enough. The suction really grabs the carpet and bogs down my self-propelled wind-tunnel Hoover. I then have to push down on the handle to tilt the front up. The thickness setting is as high as it will go. Is there some way that I can further adjust this. The machine is about eight years old.


I can help you out only if you will let me know the front width of the machine. Alongwith the height which you wan't to give raise. KIndly give the width and elevation in cms. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0471 seconds